• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.10-18
• /
• 2004

It is well known that the stratified charge combustion has many kind of advantages to combustion characteristics, such as higher thermal efficiency and less CO, NOx levels than conventional homogeneous mixture combustion. Although this combustion can be caused low fuel consumption, it is produced the high unburned hydrocarbon and soot levels because of different equivalence ratio in the combustion chamber. Moreover it has a lot of possibility of low output and misfire if the mixture gas would not be in existence around the spark plug. In this paper, fundamental studies for stratified combustion were carried out using a constant volume combustion chamber. The effect of locally mixture gas distribution according to control the direct injection and premixed injection in the chamber were examined experimentally. In addition, the effects of turbulence on stratified charge combustion process were observed by schlieren photography.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.19-26
• /
• 2004

A prior fundamental study was executed using a constant volume chamber to improve the burning properties of lean pre-mixture by the injection of active radicals generated in the sub-chamber. In consequence, RI method shows remarkable progress in the aspects of burning velocity and combustible lean limit compared with SI method. In this study, the necessary additional works have been performed to be based on the former results. We changed parameters as the initial temperature and the initial pressure of mixture. And the effects of residual gas at issue in a real engine were investigated. As a result, the effects of initial temperature were significant, but on the other hand, those of initial pressure were slight. The correlation of passage hole number between overall passage hole area was grasped. And the more detailed analysis is required on residual gas.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.201-209
• /
• 1996

This study describes the combustion characteristics of methance-air mixture with various equivalence retio and initial conditions of mixture in constant volume combustion chamber. Combustion characteristics of methane-air mixture such as combustion pressure, combustion temperature, and heat release were investigated by the measurement of combustion pressure and temperature in the combustion chamber. The results show that maximum combustion pressure, gas temperature and rate of heat release have peaks at equivalence ratio of 1.1. Combustion duration is also the shortest at the equivalence ratio of 1.1 and it is shortened as initial mixture temperature increases.

• 대한기계학회논문집
• /
• 제19권9호
• /
• pp.2308-2315
• /
• 1995

We studied the effects on the ignitability of mixture, the combustion duration, and the maximum combustion pressure, of various initial combustion factors such as temperature, pressure, and each equivalence ratio in order to identify the combustion characteristics of lean mixture and improve ignitability through the proper control of the ignition energy. It is concluded that there is an optimum turbulent intensity that enables the combustion to have the best ignitability and the shortest duration under each equivalent ratio, and the combustion duration is only dependent upon the distribution and magnitude of discharge energy within the limit of inflammability.

• 한국연소학회지
• /
• 제6권1호
• /
• pp.14-19
• /
• 2001

Interests and importance of down-scale combustor is increasing with the emerging need for miniaturized power source which is now a bottleneck of micro system development. But in down scaled combustor increased heat loss compared to thermal energy generation inhibits the usability and application of the device, so as a preliminary work of down scaled combustor fabrication. Modeling tool for the device should be established, in this study modeling approach of closed vessel combustion phenomena that can express heat loss effect and resulting quenching is proposed and the result is compared with experiment data. From this model heat loss effect following combustor scale down can be further understood, and further more design parameter and analysis tool can be obtained.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.29-36
• /
• 2003

A cylindrical constant volume combustion chamber was used to investigate the flow characteristics at spark plug and the combustion characteristics of inhomogeneous charge methane-air mixture under several parameters. The flow characteristics such as mean velocity and turbulence intensity was analyzed by hot wire anemometer. Combustion pressure development measured by piezoelectric pressure transducer was used to investigate the effect of initial charge pressure, excess air ratio and ignition times on combustion pressure and combustion duration. Mean velocity and turbulence intensity had the maximum value at 200 or 300ms and then decreased to beneath 0.05m/s gradually at 3 seconds. Second mixture is accompanied by an increase in the combustion rate, and that the higher the mass which is added in the second stage injection, the faster the burn rate.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권2호
• /
• pp.154-160
• /
• 2005

The result of combustion experiment by using the methanol-gasoline blended fuel showed that the supplying pressure appeared the maximum pressure between equivalent rate 1.1 and 1.2. and the evaporation of the fuel has been known to have been greatly influenced by surrounding temperature and the combustion chamber temperature after being injected from the injector And it is confirmed that the rate of evaporation had been suddenly dropped according to the temperature in the combustion chamber though the injected foe) had been fully evaporated Such tendency has visibly appeared when the zone is leaner. and we recognize that the rich fuel supply is needed in the operation of cold operating.

• 오토저널
• /
• 제25권5호
• /
• pp.30-33
• /
• 2003

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2010년도 춘계학술 발표회
• /
• pp.59-63
• /
• 2010

토치 점화 장치의 연소 특성을 파악하기 위하여 7개의 각기 다른 토치 점화 장치를 설계하였다. 토치 점화장치의 오리피스 직경에 따른 특성을 파악하기 위하여, 토치 점화 장치의 체적과 높이는 고정하고, 오리피스 직경을 4mm에서 16mm까지 2mm씩 증가시키며 실험하였다. 초기 화염 생성 및 전파는 질량 연소율과 연소 촉진율로 분석하였다. 질량 연소율과 연소 촉진율을 계산하기 위하여 정적 연소실 내의 평균 압력을 측정하였다. 또한 shadow graph법을 이용하여, 초기 화염 생성과 화염 전파과정 전 영역을 가시화하였다. 토치 점화 장치를 사용한 경우에는 일반적인 스파크 점화와 비교하여 질량 연소율의 기울기가 증가하였고, 연소 촉진율도 개선된것을 확인하였다. 또한 가시화된 이미지를 확인한 결과 토치 점화 장치를 사용하면 초기 화염 발달 단계에서 화염이 난류 화염으로 천이되어 연소가 촉진된것을 확인하였다.

• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.328-340
• /
• 1991

본 연구에서는 혼합기를 연소실 내로 공급하기 전에 필터를 이용하여 일정 크 기의 미립자를 제거함으로서 가능한 Mie산란의 영향을 감소시키고, 또 화학 발광의 영 향을 제거하기 위하여 광학장치의 개선 및 광학 필터를 사용하였다. 뿐만 아니라 연 소실 내의 배경광 및 반사산란광을 제거하기 위한 방법으로 입사창 및 연소실 내를 모 두 코팅을 하였다. 따라서 레이저 레일레이 산란을 이용하여 지금까지 나타난 문제 점들을 위와 같은 방법으로 개선하였을 뿐만 아니라 측정기술을 향상시켜 정적연소실 내에서의 온도를 측정함으로서 정적연소실 내에서의 온도측정이 가능하다는 것을 확인 하고, 또 그 적응성을 조사하는데 중점을 두어 실험을 하였다.