• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1131-1136
• /
• 2014

Recently, power converters installed on the specialized vessels such as LNG Carrier and Icebreaker and offshore plants mainly use diode rectifier. However, such devices cause distortion of supply voltage waveform by involving much harmonics to input current of non linearity load in rectifying operation. Distortion of supply voltage waveform can be problems such as false operation of generator, transformer and load device and deterioration of power quality. This thesis is focusing with a view to producing accurate sinusoidal AC waveform with certain load through improvement of distortion of current waveform causing under operation of rectifier by using accurate circuit of DC shaping. The result of computer simulation proved that harmonics involved in current and voltage waveform of power system can be reduced.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.2 no.2
• /
• pp.11-18
• /
• 2001

The design method of high potential generator of diagnostic X-ray apparatus by using inverter is presented. For the high potential generator, a line filter, a rectifier, a Pulse width modulation control, bridge drive, a high potential transformer and a high potential rectifier circuit were adopted. The high potential generator with switching frequency to be 40 KHz is fabricated by using design method presented in this method. The experimental results are as followings; variable volts of 0∼620 V and variable currents 50∼500 mA.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.10
• /
• pp.2230-2236
• /
• 2012

Currently, the AC-to-DC power conversion system using diode rectifiers is mainly used in large vessels. Also, to reduce the total harmonic distortion(THD) of current and voltage, this system requires an additional phase-shifting transformer which can be powered multi-pulses. In this case, due to the installation of the transformer, the spatial or economic loss occurs. This paper presents a novel active rectification scheme using silicon controlled rectifier(SCR) or insulated gate bipolar transistor(IGBT) devices on behalf of the diode rectifiers which are currently operating in large vessels such as LNG Carrier(LNGC). The proposed system can use the low voltage source and reduce current and voltage harmonics generated by nonlinear loads connected to the power distribution bus and save economic costs by removing the phase-shifting transformers which are used in conventional system. Computer simulations are performed under the electric propulsion system which is operating in current large vessel. The results are shown in support of the improvement of THD included in the current and voltage wave forms of propulsion motor.

• Proceedings of the Korean Society of Radiological Science
• /
• 1994.05a
• /
• pp.41-43
• /
• 1994

• Proceedings of the Korean Society of Radiological Science
• /
• 1995.10a
• /
• pp.142.1-142.1
• /
• 1995

• Proceedings of the KIEE Conference
• /
• 2000.07e
• /
• pp.71-73
• /
• 2000

최근 고 에너지 저장 및 발생장치의 개발은 군사용에서 산업용으로 응용되면서 각종 첨단 설비가 개발되고 있다. 본 논문에서는 전자빔 발생기로 쓰이는 Gyroklystron용 대전력, 고전압, 전류 펄스 전원장치로 입력부, 특고압 발생부, 고압 정류부 및 IGBT 펄스 스위치 구성하고 그 설계 및 개발 자료에 대하여 기술하였다. 대전력 고전압 전류펄스 전원장치를 위한 각 구성 부분의 제어 및 설계 특징은 다음과 같다. 입력부인 IGBT Inverter는 펄스 전원장치의 제어를 위하여 출력 고전압을 Feedbark System에 의해 펄스 설정 전압을 유지하도록 제어하며, 또한 펄스 출력중에 직류 고전압부의 전압강하, 즉 펄스 진압의 Drop이 커지는 것을 방지하기 위하여 Fast Dynamics를 갖도록 Feedback System을 구성하였다. 단상 특고압 승압용 변압기 3대를 직렬접속한 특고압 발생부는 PWM 제어된 전압을 입력받아 특고압으로 승압시키며 고압 펄스성 전압과 매우 높은 dV/dt 전압이 인가되므로 Stray Capacitance가 최소가 되어야 하며 절연파괴로부터 보호될 수 있어야 한다. 고압 정류부는 Inverter와 특고압 변압기에 의하여 전원이 공급되므로 교류전압의 교번 순간에 매우 높은 전압변동률을 가지는 Fast Recovery High Voltage Rectifier로 설계 제작되어졌다. 펄스 스위치인 IGBT 스위치는 Gate Driver에 의해 구동되어 지며 주어진 펄스 사양을 만족시키게 된다. 특히 소자의 전압특성을 고려하여 120KV의 전압 값을 갖도록 설계, 제작하였다.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1309-1311
• /
• 2000

본 논문에서는 입력부, 특고압 발생부 및 고압 정류부, IGBT Pulse Switch로 구성된 Gyro-klystron용 대전력, 고전압, 전류 펄스 전원장치의 설계 및 개발에 대하여 기술하였다. 대전력, 고전압, 전류 펄스 전원장치를 위한 각 구성부분의 제어 및 설계 특징은 다음과 같다. 입력부인 IGBT Inverter는 펄스 전원장치의 전압 제어를 위하여 출력 고전압을 Feedback System 제어에 의해 Pulse 설정 전압을 갖도록 제어하며, 또한 Pulse 출력중에 직류 고전압부의 전압강하, 즉 Pulse 전압의 Drop이 커지는 것을 방지하기 위하여 Fast Dynamics를 갖도록 Feedback System을 구성하였다. 3대의 단상 특고압 승압변압기가 직렬로 구성된 특고압 발생부는 PWM된 전압을 입력받아 특고압으로 승압시킨다. 특고압 변압기는 고압 Pulse성 전압과 매우 높은 dV/dt 전압이 인가되므로 Stray Capacitance가 최소가 되어야 하며 절연파괴로부터 보호될 수 있어야 한다. 고압 정류부는 Inverter와 특고압변압기에 의하여 전원이 공급되므로 교류전압의 교번순간에 매우 높은 전압 변동률을 가지는 Fast Recovery High Voltage Rectifier로 설계, 제작되어졌다. Pulse Switch인 IGBT Switch는 Gate Driver에 의해 구동되어 진다. 주어진 Pulse 사양을 만족시키며 특히 소자의 전압 특성을 고려하여 120KV의 전압값을 갖도록 설계, 제작하였다. 본 논문에서는 고전압 펄스 전원장치 각 부분의 설계에 대하여 기본적인 사항들을 제시하며, 실험결과를 통하여 제안된 방식의 우수한 특성을 입증한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.4
• /
• pp.348-361
• /
• 2001

The three-phase diode rectifier with capacitive filter is highly sensitive to line voltage unbalance. Because of its inherent nonlinear characteristics, small line voltage unbalance may cause highly unbalanced line current, causing detrimental effects on power quality. This paper presents a theoretical basis on this 'unbalance amplification effect' and derives an analytical model of line current characteristics under unbalanced line voltage condition for various modes of operation. The results provide a basic guideline for optimal design of a three-phase diode rectifier with capacitive filter that is most commonly used for interfacing various power conversion equipments to power lines.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.3
• /
• pp.304-309
• /
• 1999

In this paper, a new 24longleftarrowpulse diode rectifier system based upon the conventional series-connected 12-pulse rectifier is p proposed with the least number of switching devices and low VA rating of the additional passive components. The p proposed approach does not employ any active switching devices. Therefore, the system is rugged and simple to i implement. Detailed analysis with VA rating calculation of the components is presented and experimental results from a a 220V, 3kV A rectifier system verify the proposed concept.

• The Journal of the Korea Contents Association
• /
• v.11 no.12
• /
• pp.357-363
• /
• 2011

The aim of this study is to compare radiation dose in diagnostic X-ray radiography and calculated by different mathematical equation. The result of ESDs direct measurement and that calculated by Mori NDD-M shows the biggest difference. On the other hand, equation by Edmonds shows the lowest difference of ESDs. Also, Rectification due to the difference between direct dose measurement and calculation method commutated three-phase, single phase and inverter type, show less difference in the drive way. In conclusion, this study can be helpful for expecting radiation dose-exposure and control exposure parameters for the diagnostic x-ray radiography.