• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.6
• /
• pp.11-20
• /
• 2013

In this paper, the quantitative damage index for reinforced concrete (RC) columns with non-seismic details were presented. They are necessary to carry out the postearthquake safety evaluation of RC buildings under 5 stories without seismic details. The static cyclic test of the RC frame sub-assemblage that was an one span and actual-sized was first conducted. The specimen collapsed by the shear failure after flexural yielding of a column, lots of cracks on the surfaces of columns and beam-column joints and the cover concrete splitting at the bottom of columns occurred. The damage levels of these kinds of columns with non-seismic details were classified to five based on the load-displacement relationship by the test result. The residual story drift ratios and crack widths were then adapted as the quantitative index to evaluate the damage limit states because those values were comparatively easy to measure right after earthquakes. The highest one among the residual story drift ratios under the similar maximum story drift ratio decided on the residual story drift ratio of each damage limit state. On the other hand, the lowest and average ones among the respective residual shear and flexural widths under the similar maximum story drift ratio decided on the residual shear and flexural widths of each damage limit state, respectively. These values for each damage limit state resulted in being smaller than those by the international damage evaluation guidelines that are for seismically designed members under the same deformations.

• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.1018-1024
• /
• 1999

The effects of operating temperature and stress on degradation of components in high temperature steam generator were investigated. Several 2.25CrlMo tubes which had operated over 20 years and an unused 9CrlMoVNb tube were tested. For the former samples, the amount of $\textrm{M}_{6}\textrm{C}$ carbide and its size are increased with the aging or operating time. The precipitation behavior of carbides ($\textrm{M}_{2}\textrm{O}$, $\textrm{M}_{6}\textrm{C}$) is changed with the operating temperature of the tubes. However, unused 9CrlMoVNb samples show a different carbide precipitation process due to high chromium, vanadium, and niobium contents. The amount of Cr-rich $\textrm{M}_{23}\textrm{C}_{6}$ carbide is significantly increased with aging time, but that of $\textrm{M}_{6}\textrm{C}$ type carbide is rarely changed with aging time at elevated temperatures.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.2 s.35
• /
• pp.95-103
• /
• 2005

The interfacial reaction between 42Sn-58Bi solder (in wt.$\%$ unless specified otherwise) and electroless Ni-P/immersion Au has been investigated before and after thermal aging, with a focus on formation and growth of an intermetallic compound (IMC) layer, consumption of under bump metallurgy (UBM), and bump shear strength. The immersion Au layer with thicknesses of 0 (bare Ni), 0.1, and $1{\mu}m$ was plated on the $5{\mu}m$ thick electroless Ni-P ($14{\~}15 at.\%$P) layer. Then, the 42Sn-58Bi solder balls were fabricated on three different UBM structures by screen-printing and pre-reflow. The $Ni_3Sn_4$ layer (IMC1) was formed at the joint interface after pre-reflow for all the three UBM structures. On aging at $125^{\circ}C$, a quaternary phase (IMC2) was observed above the $Ni_3Sn_4$ layer in the Au-containing UBM structures, which was identified as $Sn_{77}Ni{15}Bi_6Au_2$ (in at.$\%$). The thick $Sn_{77}Ni{15}Bi_6Au_2$ layer deteriorated the integrity of the solder joint and the shear strength of the solder bump was decreased by about $40\%$ compared with non-aged joints.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.6
• /
• pp.523-530
• /
• 2019

For the low-Pt electrodes for polymer electrolyte fuel cells (PEMFCs), the optimization of ionomer content for anode catalyst layers was carried out. A commercial catalyst of 20 wt.% Pt/C was used instead of 50 wt.% Pt/C which is commonly used for PEMFCs. The ionomer content varies from 0.6 to 1.2 based on ionomer to carbon ratio (I/C) and the catalyst layer is formed over the electrolyte by the ultrasonic spray process. Evaluation of the prepared MEA in the unit cell showed that the optimal ionomer content of the air electrode was 0.8 on the I/C basis, while the hydrogen electrode was optimal at the relatively high ionomer content of 1.0. In addition, a large difference in cell performance was observed when the ionomer content of the hydrogen electrode was changed. Increasing the ionomer content from 0.6 to 1.0 by I/C in a hydrogen electrode with 0.05 mg/㎠ platinum loading resulted in more than double cell performance improvements on a 0.6 V. Through the analysis of various electrochemical properties in the single cell, it was assumed that the change in ionomer content of the hydrogen electrode affects the water flow between the hydrogen and air electrodes bounded by the membrane in the cell, which affects the overall performance of the cell. A more specific study will be carried out to understand the water flow mechanism in the future, and this study will show that the optimization process of hydrogen electrode can also be a very important cell design variable for the low-Pt and high-performance MEA.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.3
• /
• pp.11-17
• /
• 2009

The drop impact reliability comes to be important for evaluation of the life time of mobile electronic products such as cellular phone. The drop impact reliability of solder joint is generally affected by the kinds of pad and reflow number, therefore, the reliability evaluation is needed. Drop impact test proposed by JEDEC has been used as a standard method, however, which requires high cost and long time. The drop impact reliability can be indirectly evaluated by using high speed shear test of solder joints. Solder joints formed on 3 kinds of surface finishes OSP (Organic Solderability Preservation), ENIG (Electroless Nickel Immersion Gold) and ENEPIG (Electroless Nickel Electroless Palladium Immersion Gold) was investigated. The shear strength was analysed with the morphology change of intermetallic compound (IMC) layer according to reflow number. The layer thickness of IMC was increased with the increase of reflow number, which resulted in the decrease of the high speed shear strength and impact energy. The order of the high speed shear strength and impact energy was ENEPIG > ENIG > OSP after the 1st reflow, and ENEPIG > OSP > ENIG after 8th reflow.

• Applied Microscopy
• /
• v.29 no.1
• /
• pp.83-94
• /
• 1999

The ultrastructure of small arterioles and capillaries in the lumbrical muscles of rat digits were studied by electron microscopy and following results were obtained. 1. The diameter of small arterioles of rat digits were $12\sim20{\mu}m$, and it was relatively smaller than human $(30\sim35{\mu}m)$. 2. All the endothelial cells of small arterioles and capillaries in the lumbrical muscles of rat digits were continuous type, and they had typical morphological characteristics of continuous endothelial cells : numerous cytoplasmic pinocytic vesicles and many tight junctions between the endothelial cells. 3. In the small arterioles subendothelial layers were irregularly spaced beneath the basal lamina, and membrane to membrane contacts were found between the endothelial cells and smooth muscle cells. 4. Pericytes were often found nearby capillary endothelium, and their cytoplasmic processes surrounded part of endothelial cells. They were enclosed by basal lamina. 5. Smooth muscle cells in tunica media of small arterioles were only one layered, that is, they were terminal arterioles. Sarcoplasm of smooth muscle cell was divided to 2 areas; homogeneous or filamentous area and non-homogeneous perinuclear area. 6. The tunica adventitia contained fibroblasts with extremely attenuated cytoplasmic processes and collagen fibirls.

• Journal of Yeungnam Medical Science
• /
• v.7 no.1
• /
• pp.69-80
• /
• 1990

A clinical analysis was done on 23 patients(24 hips) with fracture of the femoral neck, who had been admitted and treated at our Orthopedic department during the period of 4 years, from Jan, 1984 to May 1988. The results were as follows : 1. 23 patients were comprised of 4 males and 19 females, and 11 patients were over 65 years old. 2. 18 cases of 24 cases were due to minor traumas such as slipping down, and for over 65 years old, all cases were due to simple minor traumas, 8 cases were showed a severe osteoporosis, below grade 3 of the Singh's index. 3. 14 cases of 24 cases were displaced subcapital fractures, and 6 cases displaced transcervical fractures. Only 4 cases were the undisplaced transcervical fractures. 4. In treatment of fractures internal fixations after manipulation were performed in 14 cases and primary arthroplasties in 10 cases. Secondary arthroplasties were done in complicated 4 cases of 14 cases treated with internal fixations. 5. Complications after internal fixation were developed in 7 cases out of 14 cases, avascular necrosis in 6, nonunions in 2, pin migrations in 3, and metal failure in 1 case. 6. In 14 arthroplasty immediate surgical fitness of femoral stem were related to late loosening of femoral stem(correlation coefficient r=-0.68, p<0.01).

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.64-72
• /
• 2022

In this study, in order to confirm the seismic performance of reinforced concrete frames retrofitted with Wall Friction Damper(WFD), the test was conducted by setting two-story Reinforced concrete frames (reference specimen, OMF-N and specimen retrofitted with internal H-shaped steel frame and WFD, OMF-ALL(H)) as main variables. The WFD Seismic Retrofit Method is a mixture of strength improvement and energy dissipation methods. To prevent the pre-destruction of existing structure by friction force before sufficient energy dissipation of WFD, the internal H-shaped steel frame and chemical anchor that penetrates the side of the beam were used to install WFD. According to the test results, the OMF-N specimen showed an brittle failure pattern caused by the shear force of the R/C column after the maximum strength was expressed. The OMF-ALL(H) specimen showed that the reduction of pinching effect and the failure of the RC column occurred. Also, the maximum strength, cumulative energy dissipation and ductility of OMF-ALL(H) increased 3.01 times, 7.2 times and 1.72 times for OMF-N. As a results, test results revealed that the WFD Seismic Retrofit Method installed on Reinforced concrete structure improves the seismic performance and the strengthening effect is valid.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.116-126
• /
• 2009

It is becoming more difficult to improve the device operating speed by shrinking the size of semiconductor devices. Therefore, for a new leap forward in the semiconductor industry, the advent of silicon opto-electronic devices, i.e., silicon photonics is more desperate. Silicon Avalanche LED is one of the prospective candidates to realize the practical silicon opto-electronic devices due to its simplicity of fabrication, repeatability, stability, high speed operation, and compatibility with silicon IC processing. We conducted the measurement of the electrical characteristics and the observation of the light-emitting phenomena using optical microscopy. We analyzed the influence of the design elements such as the shape of the light-emitting area and the depth of the $n^{+}-p^{+}$ junction with simple device modeling and simulation. We compared the results of simulation and the measurement and explained the discrepancy between the results of the simulation and the measurement, and the suggestions for the improvement were given.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.11a
• /
• pp.97-97
• /
• 1994

Wide gap 반도체 중 하나인 GaN 에너지갭이 실온에서 3.4eV 이고 직접천이형 에너지대 구조를 가지므로 청색 및 자외영역의 파장을 발광하는 발광다이오드와 바도체 레이저 다이오드의 제작에유용한 재료이다. GaN계 III족 질화물반도체가 다파장용 광원으로서 유망함을 보인 것은 1970년대 초방의기초적 연구이다. 이로부터 약 25년이 경고한 현재 청색발광다이오드가 실용화당계에 이르게 되었지만 아직까지 전류주입에 의한 레이저발진은 보고되고있지 않다. 이 논문에서는 ALGaN/GaN이중이종접합(DH) 구조의 광여기에 의한 유도방출과 광학적 이득을 측정하므로서 전류주입에의한 레이저발진의 가능성을 조사하였다. 유기금속기상에피텍셜(MOVPE)법으로 성장한 ALGaN/GaN DH구조의 표면에 수직으로 펄스발진 질소레이저(파장:337.1nm, 주기:10Hz, 폭: 8nsec) 빔의 공출력밀도를 변화시키어 조사하고 시료의단면 혹은 표면으로부터 방출되는 광 스펙트럼을 측정하였다. 입상광밀도가 증가함에 따라 자연방출에 의한 발광피크보다 낮은 에너지에서 발광강도가 큰 유도방출에 의한 피크가 370nm의 파장에서 현저하게 나타났으며 실온에서 유동방출에 필요한 입사공밀도의 임계치는 약 89㎾/$\textrm{cm}^2$이었다. 이는 GaN 단독층에 대한 유동방출의 임계치 700㎾/$\textrm{cm}^2$ 에 비하여 약 1/8정도 낮은 것이며, 이를 전류밀도로 환산하면 약 27㎄/$\textrm{cm}^2$ 정도로서 전류주입에 의하여서도 레이저발진을 실현할 수 있는 현실적인 값이다. 한편 광여기 방법으로 측정한 광학적 이득은 입사광의 밀도가 각각 100㎾/$\textrm{cm}^2$과 200㎾/$\textrm{cm}^2$일 때 34$cm^{-1}$ / 과 160 $cm^{-1}$ / 이었다. 이와 같은 결과는 GaN의밴드단 부근의 파장영역에서 AIGaN 흔정의 굴절율이 GaN의 굴절율보다 작으므로 DH구조의 채택의 의한 광의 몰입이 가능하여 임계치가 저하된 것으로 여겨진다. 또한 광학적 이득의 존재는 이 구조에 의한 극단파장 반도체 레이저다이오드의 실현 가능성을 나타내는 것이다.