• Restorative Dentistry and Endodontics
• /
• v.20 no.2
• /
• pp.699-720
• /
• 1995

This study was conducted to evaluate the effect of benzalkonium chloride solution as a wetting agent instead of water on dentin bonding with NTG-GMA/BPDM system (All-bond 2, Bisco.) and DSDM system (Aelitebond, Bisco.). Benzalkonium chloride solution is a chemical disinfectant widely used in medical and dental clinics for preoperative preparation of skin and mucosa due to its strong effect of cationic surface active detergent. Eighty freshly extracted bovine lower incisor were grinded labially to expose flat dentin surface, and then were acid-etched with 10 % phosphoric acid for 15 second, water-rinsed, and dried for 10 second with air syringe. The specimens were randomly divided into 8 groups of 10 teeth. The specimens of control group were remoistured with water and the specimens of experimental groups were remoistured with 0.1 %, 0.5 %, and 1.0 % benzalkonium chloride solution respectively. And then, the Aelitefil composite resin was bonded to the pretreated surface of the specimens by use of All-bond 2 dentin bonding system or Aelitebond dentin bonding system in equal number of the specimens. The bonded specimens were stored in $37^{\circ}C$ distilled water for 24 hours, then the tensile bond strength was measured, the mode of failure was observed, the fractured dentin surface were examined under scanning electron microscopy, and FT-IR spectroscopy was taken for the purpose of investigating the changes of the dentin surface pretreated with benzal konium chloride solution followed by each primer of the dentin bonding systems. The results were as follows : In the group of bonding with NTG-GMA/BPDM dentin bonding agent(All-bond 2), higher tensile bond strength was only seen in the experimental group remoistured with 0.1 % benzal konium chloride solution than that in water-remoistured control group(p<0.05). In the group of bonding with DSDM dentin bonding agent (Aelitebond), no significant differences were seen between the control and each one of the experimental group(p<0.05). Higher tensile bond strength were seen in NTG-GMAIBPDM dentin bonding agent group than in DSDM dentin bonding agent group regardless of remoistur ization with benzal konium chloride solution. On the examination of failure mode, cohesive and mixed failure were predominantly seen in the group of bonding with NTG-GMAIBPDM dentin bonding agent, while adhesive failure was predominantly seen in the group of bonding with DSDM dentin bonding agent. On SEM examination of fractured surfaces, no differences of findings of primed dentin surface between the groups with and without remoisturization with benzal konium chloride solution. FT-IR spectroscopy taken from the control and the experimental group reve::.led that some higher absorbance derived from the primers binding to dentin surface was seen at the group pretreated with 0.1 % benzal konium chloride solution than at the control group of remoisturizing with water.

• Restorative Dentistry and Endodontics
• /
• v.35 no.2
• /
• pp.69-79
• /
• 2010

The purpose of this study was to evaluate the effect of film thickness of various resin cements on bonding efficiency in indirect composite restoration by measurement of microtensile bond strength, polymerization shrinkage, flexural strength and modulus, fractographic FE-SEM analysis. Experimental groups were divided according to film thickness (< $50\;{\mu}m$-control, $50\;{\mu}m$-T50, $100\;{\mu}m$-T100, $150\;{\mu}m$-T150) using composite- based resin cements (Variolink II, Duo-Link) and adhesive-based resin cements (Panavia F, Rely X Unicem). The data was analyzed using ANOVA and Duncan's multiple comparison test (p < 0.05). The results were as follows ; 1. Variolink II showed higher microtensile bond strength than that of adhesive-based resin cements in all film thickness (p < 0.05) but Duo-Link did not show significant difference except control group (p > 0.05). 2. Microtensile bond strength of composite-based resin cements were decreased significantly according to increasing film thickness (p < 0.05) but adhesive-based resin cements did not show significant difference among film thickness (p > 0.05). 3. Panavia F showed significantly lower polymerization shrinkage than other resin cements (p < 0.05). 4. Composite-based resin cements showed significantly higher flexural strength and modulus than adhesive-based resin cements (p < 0.05). 5. FE-SEM examination showed uniform adhesive layer and well developed resin tags in composite-based resin cements but unclear adhesive layer and poorly developed resin tags in adhesive-based resin cements. In debonded surface examination, composite-based resin cements showed mixed failures but adhesive-based resin cements showed adhesive failures.

• 프린팅코리아
• /
• v.11 no.5
• /
• pp.98-99
• /
• 2012

에이스기계(주)(대표이사 이철)는 지난 4월 3일 고양시 킨텍스 1전시장 2층에서 신제품 및 신기술 발표회를 개최했다. 인쇄 및 포장업계 대표, 부서장, 접착기장 등 200여명이 참석한 이번 발표회에서는 시그니처 이글, 시그니처 오리엔트, 시그팩커, 인렛 스포트, 시그피더, 티어 테이핑기계 등이 소개됐다. 신제품 발표 외에도 접착기의 효율적인 관리방법에 대한 교육 및 접착기장 기술 인력 확충 방안에 대한 토론도 진행됐다.

• 프린팅코리아
• /
• v.10 no.9
• /
• pp.68-69
• /
• 2011

현재 어느 회사든 제품 생산에 들어가는 원재료비 및 공정 기본 탄가는 거의 변함이 없다. 이런 무한 경쟁 시장에서 살아남기 위한 최선의 방법은 좀 더 빠르고 정확한 셋팅을 통해 완벽한 제품의 생산성을 향상시키는 것과 남과 차별화된 제품을 생산하는 것이다. 이런 고민을 해결하고자 썬엔지니어링(주)(대표이사 곽인효)은 멀티형 컴퓨터 접착기(트윈 휘더 부착)를 개발하고 8월 8일부터 9일까지 이틀간 썬엔지니어링 부천공장에서 신제품 시연회를 가졌다.

• Proceedings of the Korean Society of Fisheries Technology Conference
• /
• 2003.05a
• /
• pp.27-29
• /
• 2003

해양생명체인 홍합(mussel)은 접착단백질(adhesive protein)을 생산, 분비함으로써 홍합 자신을 바다 속의 바위와 같은 젖은 고체표면에 단단히 부착할 수 있도록 하여 강한 파도의 충격이나 바닷속의 부력 효과에 대하여도 저항할 수 있다. 홍합접착단백질은 현재 알려진 어떠한 화학합성 접착제보다도 강력한 자연적인 접착제로 알려져 있으며 대부분의 에폭시 수지보다 두 배 정도의 커다란 인장강도를 지니고 있으면서도 휘어질 수 있는 유연성을 가지고 있는 혁신적인 물질이므로 접착제 산업계에서 매우 커다란 관심을 끌고 있다. (중략)

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2009.11a
• /
• pp.151-152
• /
• 2009

본 연구에서는 합지벽지용 수성접착제의 최적 합성조건의 설정을 통하여 기존 보다 내수성이 향상되고 합지벽지 제조공정 시 작업속도를 단축시킬 수 있도록 유동성을 개선한 VOC, 포르말린 등 환경호르몬 미 검출되는 친환경 수성접착제의 제품생산 기술을 확보 함.

• Journal of Adhesion and Interface
• /
• v.8 no.3
• /
• pp.34-45
• /
• 2007

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.11a
• /
• pp.5-5
• /
• 1997

고체추진제에 대한 비선형 점탄성 구성모델이 제시되었다 추진제 손상의 원인으로서 바인더와 AP 충전제사이의 접착분리를 고려하였으며, 점탄성 드웨팅판별식이 개발되었다. 손상에 의한 추진제의 연화는 모듈러스 저하로서 취급되었으며, 모듈러스저하 계산시에 드웨팅에 의하여 야기된 미소진공구의 모듈러스는 유한 상수로서 간주되었다. 바인더와 AP 충전제사이의 접착에너지는 180$^{\circ}$ 접착박리시험으로 측정하였다. 반복하중시의 비선형성은 전단변형률 불변량의 함수로서 고려되었다. 이 구성모델은 여러 하중조건에 대한 시편실험과 비교되어 잘 일치하였으며, 복잡한 미시구조학적 역학기구 없이 간단하게 고체 추진제의 거동을 예측할 수 있게 한다.

• Proceedings of the KAIS Fall Conference
• /
• 2001.11a
• /
• pp.91-94
• /
• 2001

리튬전지의 vent cap ass'y용의 AI foil에 LDPE(low density polyethylene)만을 coating하였으나 LDPE는 vent cover인 sus와의 열접착성이 우수하지 못하기 때문에 vent 조립시 상당한 주의가 필요했다. 그러나, LDPE보다 열접착성이 우수한 EVA(ethylene vinylacetate)와 EAA(ethylene acrylic acid)의 2중 coating된 AI foil을 이용함으로 열접착성을 향상시킬 수 있었다. 이에 따라, 전해액 누액 등의 전지 불량 원인을 제거함과 동시에 vent cap ass'y의 조립시 공정 불량까지 감소시킬 수 있었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.3
• /
• pp.9-15
• /
• 2012

This research simulates the ultrasonic wave propagation in multi-layered media using generalized formular of system response function. We made the artificial defect specimen of a rocket motor and compared with experimental wave forms. The simulation results are coincide with measured waves and we found that the pulse echo method is able to detect unbond defect at liner-propellant interface.