• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2002.04a
• /
• pp.31-32
• /
• 2002

임계노즐(critical nozzle)은 유동을 유로 최소단면부에서 초크시켜, 질량유량을 계측하기 위한 일종의 유체기구로, 최근 다양한 분야에서 널리 활용되고 있다. 압축성 기체역학의 관계식에 의하면, 임계노즐을 통하는 기체유동의 이론적인 질량유량은 노즐 목의 직경, 노즐 상류의 온도와 압력 그리고 기체의 비열비 등의 함수로 주어진다 그러나 실제 유동에서는 점성과 열전달 등의 초과로 인하여, 이론적 질량 유량과 실제유량의 비 즉 유출계수(discharge coefficient)의 값은 1.0으로 되지 않는다.

• Korean Journal of Food Science and Technology
• /
• v.2 no.2
• /
• pp.49-55
• /
• 1970

In preparation of textured soybean protein, drying process of the isolated protein affected its gelling property and other related characteristics such as water holding capacity and viscosity. In model systems, denaturation of the protein, as determined in terms of nitrogen solubility index (NSI), was appeared to be a parameter of the gel strength of soybean protein isolate. The gel strength was maximum when the protein was denatured properly during drying process of which the NSI was 43 in this experiment and decreased at either the higher or the lower NSI. It indicated that proper denaturation of the protein during drying operation is advantagous for the preparation of textured soybean protein but not neccesary to make highly undenatured one.

• Geotechnical Engineering
• /
• v.10 no.2
• /
• pp.5-24
• /
• 1994

Resilient modulus tests were performed on five cohesive soils sampled from in -service subgrades and three cohesive soils compacted in the laboratory. It was concluded that in service resilient modulus can not be estimated from the resilient modulus of laboratory specimen compacted at same water content and dry density as in -service condition. The stress at 1 percent axial strain in unconfined compression tests ($Su_{1.0%}$) was found as a good indicator of the resilient modules ($M_R$), and the unique relationship between MR and $Su_{1.0%}$ was obtained. This relationship for the laboratory compacted soil is slightly different from that for the field compacted soil and the difference is less pronounced at the confining stress level expected to exist in subgrade. A proposed relationship itself is not affected by the changes in subgrade after construction and, therefore, it is applicable to as compacted and in service subgrade conditions.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.5
• /
• pp.75-82
• /
• 1985

The fuel pump system is developed with the Model Reference Adaptive Control (M.R.A.C.) algorithm based on the Weight Least Square (W.L.S.) algorithm for the parameter Identification and the one step ahead dead-beat control with the reference model. The value of some parameters as the sampling period 7, the weighting coefficient L, and the State Variable Filter (5.V,F.) coefficient f which a(fects the system performance are selected through computer simulation. For the variation of the plante dynamics rspecially due to the change of the fuel viscosity with the ambient temperature condition, the adaptability of the control system is studied in the case of regulation and tracking.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.12
• /
• pp.1192-1198
• /
• 2011

Design routines of a torsional spring-viscous damper for a 1800 kW four cycle diesel engine-generator system are described. Modal techniques for system normalization and optimal equations for damper design are used to obtain proper design parameters of the damper. A prototype damper is manufactured according to the described design process and its two design parameters, stiffness and damping, are evaluated experimentally by torsional actuator test and free decay test. Experimentally obtained values of stiffness and damping coefficients showed good agreements with the designed values of the prototype damper.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.465-470
• /
• 2002

For measuring friction-factor of artificially-roughened surfaces which are usually applied on damper seals, flat plate test apparatus is designed and fabricated. the measurement of leakage and pressure distribution through round-hole pattern specimen with different hole area is described and a method is discussed for determining the friction-factor experimentally. Results show that the friction-factor of the round-hole pattern surfaces is bigger than that of smooth surface and increases as increasing the hole area. A empirical friction factor model for round-hole pattern surface is defined as the Moody's friction factor formula.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.1123-1127
• /
• 2005

종방향 유속의 연직분포 흐름 특성을 파악하기 위해서 중심각이 $180^{\circ}$인 단일 만곡부에서 실험을 수행하였다. 실험결과를 분석한 후 종방향 유속의 연직분포 흐름특성을 재현하기 위해서 원주형 종방향 운동 방정식에 와점성 개념을 도입하였다. Rozovskii의 종방향 그리고 연직방향 유속식들을 도입하여 이론식을 개발하였다. 이론식의 수리학적 변수들은 원심력 항, Chezy 계수, 그리고 전단유속 항들로 구성되어 있다. 이론식은 곡률반경을 따라 변화하는 만곡부 내에서 종방향 유속의 연직분포가 변형되는 현상을 재현하고 있다. 이론식은 본 연구에서 실험을 통해 취득한 관측자료와 비교한 결과 잘 일치함을 보여주고 있다.

• Journal of Ocean Engineering and Technology
• /
• v.4 no.1
• /
• pp.49-54
• /
• 1990

This study describes the application of a two dimensional depth integrated numerical model. The explict scheme of finite difference method had been applied to the model of circulation. The nonlinear terms showed a slight difference for the variations of water elevation when calculated grid was small. They were also found to be minor when calculated grid size was increased. For verification of the numerical model, numerical results were compared with predicted values and field data. In the model, the effect of nonlinear advective terms proved not to be significant.

• The KSFM Journal of Fluid Machinery
• /
• v.6 no.3 s.20
• /
• pp.15-20
• /
• 2003

For measuring friction factor of artificially-roughened surfaces which are usually applied to damper seals, flat plate test apparatus is designed and fabricated. The measurements of leakage flow and pressure distribution through round-hole patterned specimen with different hole areas are described, and a method is discussed for determining the friction factor experimentally. Results show that the friction factor of the round-hole patterned surface is bigger than that of smooth surface, and increases as increasing the hole area. A empirical friction factor model for the round-hole patterned surface can be descrived by the Moody's friction factor formula.

• Journal of the KSME
• /
• v.28 no.4
• /
• pp.313-321
• /
• 1988

어떤 구조물이 반복하중을 받으면 피로파괴를 일으킨다. 만일 이 구조물이 부식환경 속에 앗 으면 불활성 분위기나 공기 중에서 보다 빨리 파괴에 이르게 된다. 이러한 현상을 흔히 부식 피로라고 한다. 부식피로에 크게 영향을 미치는 변수들을 대략 기계적 변수, 금속학적 변수, 환경 변수로서, 기계적 변수에는 최대응력 확대계수, 응력확대계수범위, 응력비, 반복하중 주파수, 반복하중파형, 응력상태, 잔류응력, 균열의 크기 및 모양 등이 있으며 금속학적 변수로는 합금 조성, 합금원소와 불순물의 분포, 미세조직과 결정구조, 열처리, 소성가공, 집합조직 등이며 환 경변수에는 온도, 환경의 형태(기체, 액체), 부식성분의 분압 또는 농도, 전기화학적 전위, pH, 수용성 환경의 점성, 피복, 부식억제제 등이 있다. 이와 같이 부식환경 속에 있는 구조물의 파 손을 이해하기 위하여는 응력부식과 부식피로를 공부하여야 한다. 이 현상은 매우 복잡한 문 제이기 때문에 아직도 완전히 이해되지 않은 상태이고 따라서 중요한 연구대상이 되고 있다. 여기서는 응력부식과 부식피로의 파괴역학적인 측면을 소개하고자 한다.