• Tunnel and Underground Space
• /
• v.33 no.6
• /
• pp.519-533
• /
• 2023

In this study, the linear cutting tests of pick cutters were carried out on a granitic rock with the average compressive strength over 100 MPa. From the tests, the correlation between the cutter acting force and the temperature measured by infrared thermal imaging camera during rock cutting was analyzed. In every experimental condition, the maximum temperature was measured at the rock surface where the chipping occurred, and the temperature generated in the rock was closely correlated with the cutter acting force. On the other hand, the temperature of a pick cutter increased up to only 36℃ above the ambient temperature, and the correlation with the cutter force was not obvious. This can be attributed to the short cutting distance under laboratory conditions and the high thermal conductivity of the tungsten carbide inserts. However, the relatively high temperature of the tungsten carbide inserts was found to be maintained. Therefore, it is recommended that a reinforcement between the insert and the head of a pick cutter or the quality improvement of silvering brazing in the production of a cutter is necessary to maintain the high cutting performance of a pick cutter.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.493-497
• /
• 2002

In the part industry, pipe has required high accuracy in surface roughness and size. Especially, when producing the high frequency welding pipe, cutting process is very important as the finishing process that remove the hot welding bead. The objective of this paper is to investigate the hot machining high frequency welded pipe by simulation and experimental tests. To test the cutting process as hot machining, all cutting environment is reproduced in turning with heating system, and the test is accomplished by comparing with room temperature machining and hot machining in consideration of cutting force, tool wear and cutting temperature.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.2
• /
• pp.111-114
• /
• 2001

This paper presents the influence of the additive composition on flexural strength and hardness of SiC-TiC composites materials for spectacle lens cutting materials. The materials were hot-pressed at $1800^{\circ}C$ and subsequently annealed at $1910^{\circ}C$ for 3h. The heating rate was $15^{\circ}C/min$ and the cooling rate about $25^{\circ}C/min$ in from the sintering temperature to $1300^{\circ}C$. The growth of particles of spectacle lens cutting materials was analysed by SEM and crystalline phases were discussed by x-ray diffractometry. Typical fracture toughness and hardness of materials for spectacle lens cutting were $6.1MPa{\cdot}m^{1/2}$ and 14.9 GPa, respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.12
• /
• pp.110-115
• /
• 2001

In this paper, a multiple comparison was proposed to minimize the amount of coolant. And new coolant level, called "low level", was suggested to show usefulness of multiple comparison for experiments. The amount of this levee is about 1/4 of conventional coolant amount-called "high level", and dry cutting is called "none level". Using these coolant levels, the cutting temperatures of each coolant level in turning process were analyzed by analysis of variance(ANOYA)-test and a multiple comparison. As the result of ANOVA-test, we have just known that the average of temperature of each coolant level is not equal. However by Tukey's HSD, one of multiple comparison. it was analyzed that the average of temperature of low level is similar to that of high levee and different from that of none level.erent from that of none level.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.166.1-166.1
• /
• 2016

각종 부품의 내마모성 및 내식성을 개선하기 위해서 금속물질에 나노두께의 보호막층을 입혀 경도를 높이는 표면처리 기술이 개발되고 있다. TiN막은 기계적 경도, 내마모성 및 내식성이 우수하여 수없이 연구되어 왔으며 박막의 두께에 따라 다양한 색상표현이 가능하다는 연구도 진행되고 있다. 이러한 TiN 박막의 연구결과로 높은 경도와 강도를 요하는 절삭공구에 하드 코팅을 이용하여 높은 절삭력으로 고효율적인 작업환경을 조성할 수 있다. 기존에 연구되어 온 TiN박막은 Ar과 N2의 혼합가스 분위기에서 증착된 반면 본 실험에서는 영구자석을 이용한 고밀도 플라즈마로 높은 점착성과 균일한 박막 및 대면적 공정이 가능한 RF-magnetron sputtering방법을 이용하여 N2 분위기에서 TiN박막을 $100^{\circ}C{\sim}400^{\circ}C$의 온도범위에서 $100^{\circ}C$간격으로 열처리 후 증착하여 비교실험을 하였다. 이와 같이 제작된 TiN박막을 XRD(X-ray Diffraction)를 사용하여 결정성을 확인한 결과 온도가 높을수록 (111)방향의 결정성장이 뚜렷하게 나타났으며 그 외 Scratch Test와 HM-220(Micro-vicker's tester)를 사용하여 경도특성을 확인하고 SEM(Scanning Electron Microscope), AFM(Atomic Force Microscope)를 이용하여 박막의 표면형상을 측정하였다. 이러한 측정 결과로 향후에는 높은 내마모성 및 초경도가 요구되는 절삭공구 및 경질표면코팅이 필요한 금속산업분야에 적용이 가능 할 것이라 사료된다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.1
• /
• pp.9-16
• /
• 1996

This is an experimental investigation of the temperature generated in a cutting tool during the machining of stainless steel. The temperature results from the wear of the cutting tool are considered in order to investigate the relation between cause and effect of these factors. This possibility has been tested using a thermocouple technique to record temperature vs. time curves for a variety of cutting conditions. This is done by employing a thermocouple inserted on the tool tip near the major cutting edge. Temperature distributions are calculated using finite element method and compared to the contour maps measured by an optical system. It suggests that the temperature gradients and the tool performance will be dependent on certain facotrs in tool geometry when cutting this material.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.981-984
• /
• 1997

This paper deals with the relation of cutting conditions and damaged layer by investigating cutting force, cutting temperature and residual stress in high speed machining. Damaged layer was measured using optical microscope on samples prepared by metallographic techniques. The scale of this damaged layer depends upon characteristics of cutting force and cutting temperature. Damaged layer depth increases with feed per tooth and radial depth. In a different another way, damaged layer remains almost unchanged according to spindle speed. Therefore, the effective method for decreasing damaged layer is that cut down feed per tooth and radial depth.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.7
• /
• pp.90-97
• /
• 2000

This paper presents a methodology to analyze the cutting fluid effectiveness in mechanical and thermal terms simultaneously using finite element method and experimental work. Cutting fluid plays many roles in metal cutting process. Mechanically-thermally coupled effectiveness of cutting fluids affect to friction coefficient at tool-workpiece interface and cutting temperature and chip control, surface finish, tool wear and form accuracy. Through this study, it can be explained that the critical behavior of cutting fluids will be able to apply optimal environmentally conscious machining process.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.3
• /
• pp.237-251
• /
• 2013

This study aimed to estimate the axial stress and torque on a shaft in a disc cutter. The corresponding inner temperature and the surface temperature of a cutter ring were also measured by using strain gauges and thermocouples during the linear cutting tests. The maximum values of the axial stress and torque were recorded to 11.3 MPa, $171kN{\cdot}m$ respectively. They have higher correlations with normal force rather than rolling force. The results of temperature measured by thermocouples during a linear cutting test showed that the rate of increase in temperature was below $0.2^{\circ}C$. When the cutter spacing is set to be 70 mm, the inner temperature and surface temperature of a disc cutter were $0.1^{\circ}C/m$, $0.15{\sim}0.17^{\circ}C/m$ respectively. Similarly, when the cutter spacing is 90 mm, the temperature values were $0.09^{\circ}C/m$, $0.13{\sim}0.23^{\circ}C/m$ respectively.

• International Journal of Highway Engineering
• /
• v.7 no.1 s.23
• /
• pp.83-92
• /
• 2005

Maturity method is a non-destructive method for estimating in-place concrete strength as a function of time and temperature. The main objective is to use maturity method determining joint sawing and traffic opening time for whitetopping construction in Korea. Another objective is to investigate the influence of air temperature in the correspondence to slab temperature and maturity value. For determining the joint sawing and traffic opening time, thermachron i-button and strain gage were inserted in the fresh concrete in the slab and a maturity value was calculated at desired times. In-place strength was then estimated from a pre-established relationship between maturity values and compressive strength. The results showed that there are significant differences between the estimated strength obtained from maturity curve and in-place concrete strength. The reasons are that the gain of in-place concrete strength was influenced by several factors in the field such as curing conditions, air temperature, and wind speed etc. Also, the results showed that air temperature had significant influence on slab temperature and maturity value The slopes of maturity curves exponentially decrease as air temperature decreases. This means that maturity value sharply dropped as air temperature decreases.