• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.5
• /
• pp.775-781
• /
• 2011

For the measurement of absolute position of mobile robot in indoor environments, the ultrasonic positioning systems using ultrasound have been researched for several years. Most of these ultrasonic positioning systems to avoid interference between the ultrasound are used for sequential transmitting. However, due to the use of sequential transmitting, the positions of transmitter to receive an ultrasound will change when the mobile robot moves. Therefore the accuracy of positioning is reduced. In this paper, the new position estimation algorithm with weighting factor according to the time of receipt is proposed. By applying the proposed algorithm to existing Ultrasonic Satellite System(USAT), the improved USAT is configured. The positioning performance of the improved USAT with the proposed position estimation algorithm are verified by experiments.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• fall
• /
• pp.229-231
• /
• 2021

본 논문은 스테레오 카메라 영상으로부터 물체의 절대 위치를 측정하는 영상 기반 거리 측정 기술의 최적화를 목표로 한다. 기존의 openCV 라이브러리를 이용한 거리 측정 방식은 전체 영상에 대해 깊이를 계산하는 방식이다. 이에 본 논문은 YOLOv4 모델을 적용하여 검출된 특정 물체에 대해서 거리를 추출하여 속도를 향상시키는 방식을 제안하고 기존의 방식과 비교하여 성능을 평가해 보았다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.2
• /
• pp.123-129
• /
• 2016

Recently indoor positioning technologies have been studied using the acoustic signal from a smart phone. Also multi-hop indoor positioning system in which the equipments measure their relative position successively has been proposed. As the total positioning error is prone to increase due to the successively accumulated positioning error for the multi-hop system, the error analysis is required for the system design. In this paper, the absolute positioning error for the multi-hop indoor positioning equipments successively installed is analyzed, and it is verified by computer simulation. According to the results, the accumulated positioning error is linearly increased as the number of the multi-hop increases.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.7 no.2
• /
• pp.1-5
• /
• 2013

In this paper, we proposed how to estimate the walking state in the knee disarticulation prosthesis's knee angle control. In control of the knee disarticulation prosthesis, we can estimate walking state that measurement of knee angle using absolute encoder and measurement of load on the soles using strain gage. We suggested a method of estimating the current walking states which can be divided into four cases and showed the effectiveness of the method via a series of experiments.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.163-170
• /
• 2004

Since 1960s, a container shipping volume has increased dramatically and continuous on a trend of rapid growth, and so the number of containers handled at the port increases. The position measurement of the yard crane is very important for improving the operating efficiency of the port. This paper describes the method to measure the absolute position of yard crane accurately and rapidly, using both the output pulse of an encoder and infrared sensors. The crane position is calculated by counting the output pulse of an incremental encoder, which is mounted on the wheel in the crane. By the way, the wheel slippage on rail may cause some errors in the crane position information obtained from encoder pulse, and the infrared sensor is used to compensate for errors in the crane position information. The performance of proposed method is verified on experimental results with the simulator of yard crane, the size of which is about 1/10 with the real crane.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.2
• /
• pp.101-113
• /
• 2006

Arching effect occurs around the unsupported excavation surface near to tunnel face when a tunnel is excavated in a stable rock mass. If a weak fracture zone exists in front of tunnel face, a displacement occurs between tunnel face and weak fracture zone due to stress concentration. If three-dimensional absolute coordinates (longitudinal, transverse, vertical direction) is measured at tunnel face by geodetic method, the ground change in front of the tunnel face can be predicted by analysing three-dimensional absolute displacement. The purpose of this study is to verify the analysis method of three-dimensional absolute displacement by comparing the trend of displacement ratio at crown and sidewall of tunnel and the influence line/trend line of crown settlement compared with TSP results in the same section.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.9
• /
• pp.1846-1855
• /
• 2015

In this paper, a precise relative positioning with TD(time differenced) carrier phase measurements from a low-cost GNSS(Global Navigation Satellite System) receiver is proposed and analysed. The proposed method is using carrier phase measurement from a single GNSS receiver that reference receiver is not required and stand alone positioning is possible. TD operation removes the troublesome integer ambiguity resolution problem, and if the time interval is short, other error, such as, ionospheric, tropospheric delay and ephemeris error are effectively eliminated. The error analysis of the proposed method shows that a precise and positioning with carrier phase is possible. The implemented system is evaluated using a real car experiments. The results show that the horizontal positioning error was less than 3m during 10 minutes experiments, which is 4 times more precise than the results of normal code based absolute positioning.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.5
• /
• pp.76-82
• /
• 1997

The paper describes simulations and experimental results using a measuring system which utilizes the acoustic holographic method in order to exactly estimate an absolute position of a sound source. The measuring surface is installed to satisfy with a far field to the sound source and is composed of linear arrayed seven microphones. A measurement is simultaneously recorded by a reference microphone setting up a neighbour sound source and the linear arrayed seven microphones which are moved to the same interval. An absolute position of sound source is estimated by the cross-spectrum method to the received sounds between a reference and the measuring microphones. Phase differences of each microphone and time delays during scanning are compensated to the reference microphone and the measuring time of the first column. An optimal interval for each microphone in the measuring surface is decided by a numerical simulation. A source signal makes use of a sinusoid, and S/N ratio is 30dB in the experiment. The optimal microphone's interval in the simulation and the experiment is decided in order to satisfy with the Nyquist space sampling condition related to the wave length of 2kHz sinusoid. Mainlobe width of a estimated 3D hologram in the case of 2kHz source signal is decreased to 87% and 30% in comparison to 500Hz and 1kHz, and then a valid of simulation results is confirmed. Therefore, we verified a utilization of the study for a sound source estimation using 3ㅇ acoustic holographic method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1437-1443
• /
• 2009

This paper is presented an simultaneous localization and mapping (SLAM) algorithm using ultrasonic for robot and electric compass, encoder, and gyro. Generally, localization based upon electric compass, encoder, and gyro can be measured just local position in workspace. However, actual robot must need an information of the absolute position in workspace to perform its mission, Absolute position in workspace could be calculated using SLAM algorithm. To implement SLAM in this paper, a map is built using ultrasonic sensor and hierarchical map building method. And then, we the map will be transformed into a feature map. The absolute position could be calculated using the feature map and map mapping method. As a test bed, we designed and construct an autonomous robot and showed the experimental performance of the proposed SLAM algorithm based on feature map. Experimental result, we verified that robot can found all absolute position on experiments using proposed SLAM algorithm.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1996.10a
• /
• pp.19-23
• /
• 1996

이 연구는 영상 홀로그래픽의 원리를 이용하여 직선배열형 음향센서 어레이를 측정대상에 직접 주사시켜 고분해능을 가지고 짧은 계측시간에 정확한 음원의 절대위치를 추저에 그 목적을 두고 있다. 시뮬레이션을 통하여 재생시 평생간섭파의 영향을 제거하기 위해 측정면의 길이와 센서간격을 나이키스트조건이 성립하는 최적조건을 찾아내었고, 실험을 통하여 실제음장에서 음원 위치 추정을 행하여 비교.검토한 결과 , 계산기상의 시뮬레이션 결과와 일치함이 확인되었다.