• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.11
• /
• pp.725-729
• /
• 2014

In this study, a transparent conductive oxide (TCO)-less dye-sensitized solar cells (DSSCs) was fabricated by using titanium (Ti) electrode to replace the Fluorine-doped tin oxide (FTO) for the reduction of manufacturing cost. Ti film was formed by electron beam evaporation method and the results showed the sheet resistance of Ti electrodes with a thikness of 500 nm similar to FTO. In case of power conversion efficiency (PCE), a DSSC with Ti electrodes showed a lower value than that with FTO by 0.38%. For the investigation of the difference, the DSSCs were measured and analyzed by using electrochemical impedance analyzer (EIS).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.10
• /
• pp.736-740
• /
• 2013

In this study, the influence of electrochemical properties by mixing Tetrabutylammonium hydroxide (TBAOH) and ammonium hydroxide (NH4OH) electrode on the dssc. The titanias were prepared using a sol-gel method by mixing Tetrabutylammonium hydroxide and Ammonium hydroxide. The $TiO_2$ nanopowder prepared by sol-gel methode, and to improve the distributed properties of $TiO_2$ nanopowder, the TBAOH and NH4OH was added. The I-V values of cells show that the Tetrabutylammonium has 6.51% efficiency.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.172-175
• /
• 2007

The Performance of a PEMFC stack is strongly dependent on the uniform reactants distribution on MEA. The uniform distribution can be achieved by flow-field pattern and manifold design optimized to satisfy operating conditions. This paper investigates uniform reactants distribution in channels by changing manifold shape and inlet mass flow rate. Typical U and Z shape and modified U and Z shape manifolds with buffer zone were designed. To check the uniform reactants distribution, standard deviation of mass flow rate was compared. The numerical results show that the inlet mass flow rate, inlet shape, and manifolds shape are critical factor for uniform distribution.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.198-202
• /
• 2005

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1511-1513
• /
• 1998

The purpose of this study is to research and develop PEO/PVDF electrolytes and $LiMn_2O_4$ composite cathode for all-solid state lithium rechargeable battery. We investigated AC impedance response and charge/discharge cycling of $LiMn_2O_4$/SPE/Li cells. The cell resistance was decreased so much initial charge process from 0% SOC to 100% SOC. The radius of semicircle of $LiMn_2O_4$/SPE/Li cell was so much from initial state to 20th cycling. The discharge capacity of the $LiMn_2O_4$ composite cathode was 144mAh/g based on $LiMn_2O_4$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.3
• /
• pp.175-179
• /
• 2015

In this study, we propose Ti hole pattern structure on the transparent conductive oxide (TCO) less dye-sensitized solar cells (DSSCs) using the lift-off process to improve the low light transmittance and low efficiency caused by opaque Ti electrode. The formation of Ti hole patterns make it possible to move the dye adsorption and electrolyte. The DSSCs with Ti hole patterns showed a higher photoelectric conversion efficiency (PCE) than those with general structure by 11.1%. As a result, The Ti hole pattern structure can be improved to increase the light absorption of the dyes and PCE of the TCO-less DSSCs is also increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.277-278
• /
• 2008

Orthorhombic $LiMnO_2$(o-$LiMnO_2$) has attracted public attentions as a cathode materials of Lithium ion battery because it has low cost and high theoretical discharge capacity of 285mAh $g^{-1}$. In our study, o-$LiMnO_2$ is synthesized by quenching method. To verify their phase structure, X-ray diffraction is accomplished. Test cells are assembled to check electrochemical characteristics using acquired o-$LiMnO_2$ cathode and carbon anode. Charge/Discharge cycling was carried out for 50cycles. And impedance was measured at 1, 2, 5, 10, 30, 50cycle. During cycle test, the max discharge capacity was recorded 139mAh $g^{-1}$ at 10cycle.

• Journal of Industrial Technology
• /
• v.33 no.A
• /
• pp.41-48
• /
• 2013

A statistical downscaling methodology has been developed to investigate future daily wind speeds over South Korea. This methodology includes calibration of the statistical downscaling model by using large-scale atmospheric variables encompassing NCEP/NCAR reanalysis data, validation of the model for the calibration period, and estimation of the future wind speed based on the general circulation model (GCM) outputs of scenario A1B of the CGCM3. Based on the scenario A1B of the CGCM3 model, the potential impacts of climate change on the daily surface wind speed is relatively small (+/- 1m/s) in South Korea.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1685-1687
• /
• 1996

Recently, conducting polymer has been much attracted as novel materials because of its electronic behavior and functional application by doping process. In this paper, we electrochemically synthesized polyaniline films under potential sweep conditions, which exhibit high electric conductivity about 200 S/cm. Specific energy of 600 Wh/kg and Ah efficiency 98% were achieved during the charge/discharge cycling using liquid electrolyte system. On the other hand, consequences of the cycling were 260 Wh/kg and 95% Ah efficiency using polyethylene oxide(PEO) based solid-state electrolyte system.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.701-706
• /
• 2003

Fuel cell is remarkable for one of the clean energy recently. But in the fuel cell case, it has characteristics with low voltage and high current. Therefore, for using domestic power, it should be changed to the power source with commercial voltage and frequency. In this paper fuel cell simulator having electrical characteristics is designed and constructed instead of fuel cell stack. Voltage generated from fuel cell is from 39V to 72V dc and should be boosted to 400v do for home appliances. A stand alone system including the inverter and DC/DC converter for the fuel cell is then proposed. Experimental result is used to support the analysis.