• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.5
• /
• pp.386-393
• /
• 2007

Charge-pump high voltage inverter for Plasma backlight using CIM(Current Injection Method) is proposed in this paper. Adoption of ERC(Energy Recovery Circuit) is a new attempt in high voltage inverter so that it is not only energy recovery but also improvement of discharge stability and system unstability which is interrupted by noise. Using a charge-pump technique enables low voltage switches to be usable, the cost can be reduced. CIM is adopted to achieve high speed energy recovery in proposed circuit. Operations of the proposed circuit are analyzed for each mode. The proposed circuit is verified to be applicable on a 32 inch plasma backlight panel by experimental results.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.481-487
• /
• 2010

The equivalent circuits intended to analyze the characteristics of IPT systems can be shown in structures similar to those of existing transformers. IPT systems are composed of combinations of the primary and secondary coils based on magnetic coupling, and the performances are determined by the lengths or the degrees of magnetic coupling of current collecting conductors(secondary) and feeding rails (primary) and system performances become the maximum when they are coupled under the optimum condition. To maximize the output currents of the secondary side, the shapes of iron cores and the structures of coils etc should be considered. To this end, three types of IPT system simulation models were selected and they were analyzed using an electromagnetic field analyzing program. To compare the types with each other, the sizes of the IPT systems and the primary side voltages etc were made to be the same. The electromagnetic fields were analyzed while changing the thicknesses of the cores and the lengths of the air gap etc and the results were analyzed in order to derive the optimum specifications.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.1
• /
• pp.7-12
• /
• 2000

As an essential technology for the FED, VFD and PDP packaging having merits of no glass frit and no glass tube usage, two sodalime glass substrates were electrostatically-bonded in a vacuum environment, and the bond properties were compared with the case of bonding in atmosphere. The glass wafer pairs bonded in vacuum using a-Si interlayer had a relatively lower bond strength than the ones bonded in atmosphere under same bonding conditions (temperature and voltage). And the bond strength was increased in the case of oxygen ambient. Through the XPS and SIMS analyses fur the surface region of a-silicon and bulk glass, it might be concluded that the lower bonding strength was originated from the inactive silicon oxide growth occurred during the electrostatic bonding process due to oxygen deficiency in vacuum.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.12
• /
• pp.1716-1721
• /
• 2014

In this paper, a study on automation method for the circuit/EM (Electro-Magnetic) simulation is carried out to analyze effectively the SI/PI (Signal Integrity/Power Integrity) issues which occur on circuits and/or PCBs (Printed Circuit Boards). For the automation of the circuit/EM simulation, algorithms performing each process of the SI/PI analysis automatically (such as ports setup, circuit definition and SI/PI evaluation) are developed; thereby automation system for the SI/PI analysis is constructed with the algorithms. The automation of the circuit/EM simulation is accomplished in the environment of the C/S (Client/Server) architecture in order to reduce resources such as high cost computers demanded for the SI/PI analysis. The automation method for the SI/PI analyses proposed in this paper reduces effort, time, and cost spent on the environment setup for simulation and the SI/PI analysis process. In addition, the proposed method includes automation of the documenting process, which organizes, records and displays the SI/PI analysis results automatically for users.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.18-22
• /
• 2012

This paper presents the magnetic field analysis of the racetrack double pancake field coil for the 10 MW class superconducting wind turbine which is considered to be the next generation of wind turbines using the 3 Dimensional FEM(Finite Elements Method). Generally, the racetrack-shaped field coil which is wound by the second generation(2G) superconducting wire in the longer axial direction is used, because the racetrack-shaped field coil generates the higher magnetic field density at the minimum size and reduces the synchronous reactance. To analysis the performance of the wind turbines, It is important to calculate the distribution of magnetic flux density at the straight parts and both end sections of the racetrack-shaped high temperature superconductivity(HTS) field coil. In addition, Lorentz force acting on the superconducting wire is calculated by the analysis of the magnetic field and it is important that through this way Lorentz force can be used as a parameter in the mechanical analysis which analyzes the mechanical stress on the racetrack-shaped field coil.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.2
• /
• pp.6-12
• /
• 2001

When CBR source traffics are loaded to ATM switch and broadband network termination, CTD values of ATM switch and broadband network termination are measured and then the values of CTD in the domestic region arc estimated. The estimation values of CTD satisfy the objective of CTD in the domestic region allocated by allocation rules of 1.356. The peak-to-peak CDV allocation method based On Chernoff accumulation method is proposed and applied to the nodes of national portion. From the result of numerical analysis, the proposed method is more accurate than the equal allocation method for peak -to-peak CDV in case that the CDVs at each node and the number of ATM nodes on the path increase.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.3
• /
• pp.303-308
• /
• 2008

The induction heating is more efficient for a plate bending because of its easy operation and control of working parameters, compared with the heating by a gas torch. The existing axis symmetric analysis method could neither handle initial curved plates nor be used in the optimization of coil shapes because of its limit of an axis symmetric coil shape. But the proposed method using some discrete part models and analysis processes could overcome these difficulties and show more accurate results in temperatures and deflections of flat or curved plates with initial curvature than those in the existing axis symmetric analysis method. This method is composed of the multi-disciplinary analyses such as an electro magnetic analysis, a heat transfer analysis and a deformation analysis based on inherent strain approach per each step. Traditionally, the coil shape in the induction heating is circular shape and it needs the moving process along heating lines. To overcome this, the 'Long Type Coil' with some linear parallel coils was proposed. It did not need the moving process along heating lines and reduced the heating process time. The results of experiments were compared with those of the simulation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.1
• /
• pp.23-26
• /
• 2003

This paper presents conceptual design and 3-D electromagnetic analysis of IMVA transformer with BSCCO-2223 High Tc Superconducting (HTS) tapes. The rated voltages of each sides of the transformer are 22.9 kV and 6.6 kV, and double pancake windings were adopted. High voltage and Low voltage sides were composed of several double pancake windings. Four HTS tapes were wound in parallel for the windings of low voltage side and were transposed in order to distribute the currents equally in each conductor The transformer core was designed as a shell type core made of laminated silicon steel plates and the core is separated with the windings by a cryostat with Fiberglass Reinforced Plastics(FRP). A sub-cooling system using L$N_2$ were designed to maintain the coolant temperature 65K. Finally perpendicular components of magnetic field applied to tapes were calculated 0.247 in the rated operation using 3-D analysis. A real 1MVA HTS transformer will be manufactured in near future based on the design parameters presented in this paper.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1494-1495
• /
• 2006

A complete finite element analysis method for discharge onset process, which is governed and coupled by charge transport equation and electric field equation, was presented. The charge transport equation of first order was transformed into a second-order one by utilizing the artificial diffusion scheme. The two second-order equations were analyzed by the finite element formulation which is well-developed for second-order ones. The Fowler-Nordheim injection boundary condition was adopted for charge transport equation. After verifying the numerical results by comparing to the analytic solutions using parallel plane electrodes with one carrier system, we extended the result to blade-plane electrodes in 2D xy geometry with three carriers system. Radius of the sharp tip was taken to be 50 ${\mu}m$. When this sharp geometry was solved by utilizing the space discretizing methods, the very sharp tip was found to cause a singularity in electric field and space charge distribution around the tip. To avoid these numerical difficulties in the FEM, finer meshes, a higher order shape function, and artificial diffusion scheme were employed.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.864-865
• /
• 2007

외전형 유도전동기는 내전형에 비해 회전자가 외부에 존재하는 특징을 가지고 있어서 제품의 소형화 및 경량화를 시킬 수 있다는 장점이 있다. 하지만 외전형은 회전자의 직경이 내전형에 비하여 크기 때문에 조립 공정상에 존재하게 되는 회전자와 고정자간의 이심률에 따른 제품 전체의 불균형력이 상대적으로 크며, 이로 인해 모터의 정속적인 운전 방해 및 불규칙한 출력토크로 인한 제품 작동상의 오류발생이 더 크게 나타난다. 본 논문에서는 외전형 유도전동기에서 존재하는 이심률의 크기에 따른 불균형력이 최소화 될 수 있는 슬롯형태를 찾기 위해 회전자 슬롯의 형태를 전폐형, 반폐형, 개구형태의 3가지형태로 변경시킨 후, 이를 전자장 해석을 통해 불균형력을 비교하였다. 또한 이심률이 증가함에 따라 나타나는 불균형력의 증대를 슬롯 형태에 따라 비교 분석하여, 불균형력에 최적화된 외전형 모터의 슬롯형태를 알아보았다.