• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.342-349
• /
• 2011

The purpose of this paper is to describe experimental results about the butt welding and bead on plate welding of the high power Continuous Wave (CW) Fiber laser for Ultra-low carbon Interstitial Free(IF) steel plate for gear part of car. After being welded of the gear parts by the fiber laser and electron beam Microstructures of melting zone had been mixed acicular, granular bainitic, quasi-polygonal and widmanstatten ferrite because of a radical thermal diffusion after welding, difference of critical volume and grain size. As a result of experiment, when gear parts were welded by the fiber laser and electron beam, the fiber laser welding has been stable properties without internal defects more than the electron beam welding. Therefore it has the very advantages of welding high quality and productivity more than conventional melting method. The optimal welding processing parameters for gear parts were as follows : the laser power and welding speed were 3kWatt, 30mm/sec respectively. At this time heat input was $21.2{\times}10^3J/cm^2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.391-391
• /
• 2010

초전도 가속공동기의 소재는 순수 Nb로 제작하는 것이 일반적이다. 그러나 극저온 (2-4.5K)에서 열전도도가 낮아서 순간적인 Normal zone이 발생되면 이를 원활이 냉각되지 못하여 Quench로 발생 가능성이 높다. 초전도 가속공동기는 약 3 mm 두께의 Nb 판을 이용하는데, 500 MHz 공동기의 전자기장의 침투깊이가 불과 수 nm에 불과해서 나머지 부분은 사실상 불필요한 부분이다. 따라서 이 경우 매우 비싼 초전도 공동기 소재의 낭비가 매우 심하다. 또 Nb 판으로 공동기를 제작할 경우 매우 비싸고 시간이 많이 소요되는 전자빔용접을 해야 하고 또 제작 후 표면처리가 매우 번거롭고 장시간을 요한다. 이러한 단점을 보완하기 위해서 구리판으로 성형가공법을 이용하여 공동기를 제작하고, 내부의 RF 표면에 수 ${\mu}m$ 두께의 Nb 코팅을 한 공동기를 개발하여 CERN의 LEP에 설치하여 실용화하였다. 이렇게 하여 소재비용을 포함한 초전도 공동기 제작, 표면처리 비용 절감은 만족할 만한 결과를 얻었다. 구리의 높은 열전도에 의한 고 가속전기장의 기대와 달리 가속전기장이 최고 약 7 MV/m 정도로 제한되었다. 그후 꾸준히 연구개발을 진행하여 현재 약 22 MV/m 까지 기록하고 있으나, 순수 Nb 공동기의 약 50 MV/m에 비하면 현저히 낮은 수준이다. 본 연구는 Nb 코팅법을 이용하여 Nb 코팅 초전도 공동기의 한계를 넓히기 위한 것이다. 본 발표는 "Sputtering 법에 의한 초전도 Nb coating 소재의 RF 한계 극복 연구"의 기초연구 결과를 보고하고자 한다.

• Laser Solutions
• /
• v.1 no.1
• /
• pp.11-17
• /
• 1998

The electron beam welding system has the advantages of the high power density, narrow welding section, and small thermal distortion of a workpiece. Recently, the electron beam welding system is widely used to the airplane engineering, nuclear power plant, and automobile industry. In the present paper, the structural analyses on the vacuum chamber of the electron beam welding system are performed by the F.E.M. analysis. The stiffening characteristics on the geometric shape, stiffener height and stiffener span are investigated. The deflection of the stiffened vacuum chamber under pressure is minimized by longitudinal and transverse stiffeners which are continuous in both direction.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1320-1321
• /
• 2008

펄스파워기술은 저장된 전자에너지를 시공간적으로 압축 중첩하여 극히 짧은 시간안에 대전력을 발생시켜 좁은 공간에 에너지를 집중 공급하는 기술이다. 여기에는 에너지를 저장하는 충전장치에 대한 기술과, 빠른 시간에 에너지를 방출하는 스위칭기술, 파형을 성형하는 펄스포밍 네트워크 기술등을 포함하며, 이를 이용한 응용기술로 플라즈마건, 이온빔 가속장치, 펄스성형용접, 수처리 발라스트, 파암장비, 코일건, 레일건 등이 있으며, 이 응용분야에 오래전부터 이용되어 왔다. 이러한 분야에 적용되는 펄스전원장치는 이동성이 용이해야 하고, 부피 또한 작은 구조를 가져야 한다. 본 논문은 고집적화 펄스전원장치의 츠로토 타입 설계, 제작, 실험에 관한 논문으로 그 중 펄스성형을 이뤄내는 인덕터에 대한 성능 실험 결과를 위주로 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.114-118
• /
• 2007

Design and fabrication of a 30-tonf-class full-scale regenerative cooling combustion chamber of a liquid rocket engine for a ground hot firing test are described. It has chamber pressure of 60 bar and nozzle expansion ration of 12 and manufactured to have a single welded structure of· the mixing head and the chamber. The material of the mixing head is STS316L which has excellent mechanical property in cryogenic condition. The chamber comprise of the cylinder, nozzle throat, and 1st/2nd nozzle parts. The material of the inner jacket is copper alloy/STS329J1/STS316L and that of the outer jacket is STS329J1. The components of· the combustor were manufactured by mechanical processing including lathing, milling, MCT, rolling and pressing. The machined components were integrated to a single body by means of general welding, electron beam welding(EBW), and brazing.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.4
• /
• pp.76-82
• /
• 2008

Alloy 718 nozzle component was manufactured by hot forging and electron beam welding process. In this process, 718 billets produced in domestic company were used and evaluated. Before performing industrial scale hot forging, small size hot compression tests were carried out under various process conditions and then microstructural evaluations were analyzed. Using the results, FEM simulations were performed in order to optimize the hot working process. After hot working, forged work-pieces were machined and welded by electron beam. Final nozzle components were heat treated and their microstructure and mechanical properties were investigated.

• Journal of Welding and Joining
• /
• v.27 no.3
• /
• pp.73-79
• /
• 2009

This present paper investigated the mechanical properties and the microstructures of each penetration shapes classifying the conduction shape area and the keyhole shape area about electron beam welded 120(T)mm thick plated aluminum 5052 112H. As a result the penetration depth is increased linearly according to the output power, but the aspect ratio is decreased after the regular output power. In the conduction shape area, the Heat affected zone is observed relatively wider than the keyhole shape area. In the material front surface of the welded specimen, the width is decreased but the width in the material rear surface is increased. After the measuring the Micro Vikers Hardness, it showed almost similar hardness range in all parts, and after testing the tensile strength, the ultimate tensile strength is similar to the ultimate tensile strength of the base material in all the specimens, also the fracture point was generated in the base materials of all the samples. In the result of the impact test, impact absorbed energy of the Keyhole shape area is turned up very high, and also shown up the effect about four times of fracture toughness comparing the base material. In the last result of observing the fractographs, typical ductile fraction is shown in each weld metal, and in the basic material, the dimple fraction is shown. The weld metals are shown that there are no other developments of any new chemical compound during the fastness melting and solidification.

• Journal of Welding and Joining
• /
• v.20 no.4
• /
• pp.525-534
• /
• 2002

During laser spot welding of the braun tube electron gun, phenomena such as serious spattering and oxidative reaction, etc. were occurred. The spatter occurred from weld pool affects the braun tube, namely it blocks up a very small hole on the shadow mask and causes short circuit between two roles of the electron gun. We guessed that high power density and oxidative reaction are main sources of these problems. So, we studied to prevent and to reduce spatter occurring in spot welding of the braun tube electron gun using pulsed Nd:YAG laser. The characteristics of laser output power was estimated, and the loss of laser energy by optical parameter and spatter was measured by powermeter. The effects of welding parameters, laser defocused distance and incident angle, were investigated on the shape and penetration depth of the laser welded bead in flare and flange joints. From these results, the laser peak power was a major factor to control penetration depth and to occur spatter. It was found that the losses of laser energy by optic parameter and sticked spatter affect seriously laser weldability of thin sheets. The deepest penetration depth is gotten on focal position, and a "bead transition" occurred with a slight displacement of focal position relative to the workpiece surface and the absorption rate of the laser energy is affected by the shape factor of the workpiece. When we changed the incident angle of laser beam, the penetration depth was decreased a little with increasing of the incident angle, and the bead width was increased. The spattering was prevented by considering laser beam energy and incident angle.ent angle.

• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.50-57
• /
• 2013

Characterization of microstructures and cryogenic mechanical properties of electro beam (EB) welds between cast and forged Inconel 718 superalloys has been investigated. Optimal EBW condition was found in the beam current range of 36~39 mA with the constant travel speed of 12 mm/s and arc voltage of 120 kV for 10 mm-thick specimens. Electron beam current lower than 25 mA caused to occur the liquation microfissuring in cast-side heat affected zone (HAZ) of EB welds. The HAZ liquation microfissure was found on the liquated grain boundaries with resolidified ${\gamma}/Laves$ and ${\gamma}/NbC$ eutectic constituents. EBW produced welds showing a fine dendritic structure with relatively discrete Laves phase due to fast cooling rate. After post weld aging treatment, blocky Laves phase and formation of ${\gamma}^{\prime}+{\gamma}^{{\prime}{\prime}}$ strengtheners were observed. Presence of primary strengthener and coarse Laves particles in PWHT weld may cause to reduce micro-plastic zone ahead of a crack, leading to a significant decrease in Charpy impact toughness at $-196^{\circ}C$. Fracture initiation and propagation induced by Charpy impact testing were discussed in terms of the dislocation structures ahead of crack arisen from the fractured Laves phase.

• Transactions of Materials Processing
• /
• v.17 no.7
• /
• pp.523-527
• /
• 2008

In this study, mechanical properties of Alloy 718 welded after forgings for jet propulsion component was investigated. Hot-forged and machined work-pieces($230mm\times70mm\times15mm$) which have different grain sizes are welded by electron beam welding technique. After welding, the components were solution heat-treated and aged. Samples were sectioned to analyze the microstructural evolution and formation of micro-crack. It was found that HAZ grain boundary liquation crack generally initiates in the coarse grains rather than the fine grains. Needle-like phases with high Nb contents were found at the outer part near the base metal. Vickers hardness and tensile tests were carried out at room temperature and at $649^{\circ}C$. The tensile properties of electron beam welding specimens exhibited around 100MPa and 10% decrease in strength and elongation, respectively.