• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.12
• /
• pp.75-82
• /
• 2010

This paper presents a wideband ${\Delta}{\Sigma}$ fractional-N frequency synthesizer for a multi-band single chip CMOS RFIC transceivers. A wideband VCO utilizes a 6-bit switched capacitor array bank for 2340~3940 MHz frequency range. VCO frequency calibration circuit is designed for optimal capacitor bank code selection before phase locking process. It finishes the calibration process in $2{\mu}s$ over the whole frequency band. The LO generation block has selectable multiple division ratios of ${\div}2$, ${\div}16$, and ${\div}32$ to generate LO I/Q signals for T-DMB/DAB/FM Radio systems in L-Band (1173~1973 MHz), VHF-III (147~246 MHz), VFH-II (74~123 MHz), respectively. The measured integrated phase noise is quite low as it is lower than 0.8 degree RMS over the whole frequency band. Total locking time of the ${\Delta}{\Sigma}$ frequency synthesizer including VCO frequency calibration time is less than $50{\mu}s$. The wideband ${\Delta}{\Sigma}$ fractional-N frequency synthesizer is fabricated in $0.13{\mu}m$ CMOS technology, and it consumes 15.8 mA from 1.2 V DC supply.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.257-259
• /
• 2019

본 논문은 광물 탐사를 위한 25kW급 양극성 펄스전원장치에 대해 기술한다. 소프트스위칭 기반의 고효율 LCC 공진형 컨버터와 풀 브리지 기반 양극성 펄스 스위칭부로 구성된 단위 모듈(500V, 12.5A)을 기반으로 설계한다. LCC 공진형 컨버터는 전류의 rms값을 줄이기 위해 공진 전류모양을 사다리꼴 형태로 설계하여 도전 손실측면에서 크게 개선되었고, 높은 전력밀도를 달성하기 위해 변압기의 누설 인덕턴스를 공진 파라메터로 활용한다. 추가적으로, 짧은 펄스폭을 가지도록 설계된 게이트 구동 회로는 출력을 DC에서 8kHz의 넓은 주파수 범위에서 동작시킬 뿐만 아니라 게이트 신호를 전달하기 위한 변압기의 사이즈를 줄이기 위해 제안된다. 단위모듈 형태로 개발된 양극성 펄스전원장치는 4개의 모듈이 직병렬로 결선되어 부하조건에 따라 Grounded dipole mode (2kV, 12.5A) 또는 Loop mode (500V, 50A)로 동작한다. 4모듈 직병렬 운전 시 발생하는 모듈 간 전압 불균형 문제를 해결하기 위해 메인 변압기에 보상권선이 감긴다. 본 논문에서는 개발된 양극성 펄스전원 장치의 설계를 저항부하 실험 및 태백산 탐사시험 결과를 바탕으로 검증한다.

• Journal of the Korean Society of Safety
• /
• v.25 no.2
• /
• pp.29-34
• /
• 2010

This paper is aimed to develop monitoring software for detecting the characteristics of current and voltage signals for series arc on electric wire. In order to attain this purpose, the characteristics of series arc were analyzed by the current and voltage signals on electric wire which were installed, and also analyzed by the changes of RMS, instantaneous of waveform value in time domain and THD in frequency domain. Monitoring program which analyze the signal was developed by Labview which can analyze in time domain and frequency domain, and save data. Experimental setup for detecting verification of monitoring program was composed loads of a lamp, an electric heater and an electric fan loads which were usually using. Measurement points for detecting verification of monitoring program were selected at both the panel board and the arc generator at the same time. As results of the experiments by monitoring program, the arc current waveform showed the same characteristic in all measurement points of all load. But the arc voltage waveform was different in each measurement point. When arc occurred, the THD of current value increased above 20%. The results of this study will be effectively used in developing the preventive system of electric fire by series arc.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.7
• /
• pp.379-386
• /
• 2005

Among various kinds of hearing aids which have been developed so far. the conventional air conduction hearing aids have some problems such as the acoustic distortion, an howling effect due to acoustic feedback. Another type of hearing aid. the cochlear implant system can be applied to the profound imparied person. However. it shows the disadvantage that there is no possibility of recovery of the acoustic organ such as ossicle. On the other hand. the implantable middle ear heaving device directly vibratos the ossicular chain and has better sound qualify. good cosmetics for appearance. and wide frequency responses so that it can overcome the defects or the conventional hearing aids. In this paper, a mathematical modeling and a momentum equation derivation of the DET has been performed. For the optimization of the structure dimension generating maximal vibrating force of the DET. the computer simulation using a finite element analysis (FEA) software has been performed. Also. the vibrating transducer has been designed to make the frequency characteristics or the transducer be similar to those of the normal middle ear. Through the experimental results, the measured vibration characteristics of the DET has been evaluated to verify the performance for the application to implantable middle ear hearing devices.