자립 운전시 전력조절기는 일반적으로 태양광 발전에서 사용을 할 경우 부하에 의해 출력이 결정되어 최대전력 추종을 할 수 없는 구조로 되어있다. 본 연구에서는 자립 운전시의 태양광 발전시스템이 안정적인 최대전력 추종을 할 수 있도록 에너지 저장장치가 결합된 구조를 제안하였다. 이러한 구조에서는 태양광 발전의 전력 손실을 줄이고 또한 태양광 발전 전력이 부족할 경우에서도 부하 측의 안정적인 동작을 보장하기 위하여 에너지 저장장치와 DC-DC 양방향 컨버터를 이용한다. 에너지 저장장치의 한 예로 슈퍼커패시터를 충 방전함으로써 태양광 발전 에너지에 의한 안정적인 출력을 낼 수 있고, 태양광 발전 전력의 효율적인 사용을 위한 전력조절 시스템의 아키텍처를 제안하고자 한다.
Journal of Korea Society of Industrial Information Systems
/
v.8
no.2
/
pp.84-91
/
2003
KOMPSAT series use software-controlled unregulated bus system in which the main bus is directly connected to a battery and the duty-ratio for PWM switch is controlled by the on-board satellite software. This paper proposes a new power-stage circuit that can be available for modularization of the power regulator which is used at the software-controlled unregulated bus system satellite. And we analyze the proposed power-stage operation according to its operating modes and verify it by performing software simulation and hardware experiment using prototype. We construct a parallel-module converter which is composed of proposed power-stages and perform experiment to verify modular characteristics of the proposed power-stage. Finally, we verify the usefulness of the proposed power-stage by comparing above results with those of a parallel-module converter made of conventional power-stages.
정지궤도 복합위성용 전력조절장치는 위성의 전력버스에 필요한 전력을 조절하고 배터리의 충전과 방전을 제어하고 관리한다. 전력조절장치의 용량은 1kw로 하고 태양 전지의 어레이는 4개의 패널로 구성되며 S3R(Sequential Switching Shunt Regulator)을 이용하여 조절된 버스전압은 완전조절 50Vdc으로 한다. 변환된 전력은 위성부하에 필요한 전력을 분배하는 PDM(Power Distribution Module)에 공급된다. 남은 전력은 BCR(Battery Charge Regulator)를 통해 배터리에 전력을 충전하고 전력이 부족할 때 BDR(Battery Discharge Regulator)를 통해 방전을 하여 버스전압에 전력을 공급한다.
Journal of Satellite, Information and Communications
/
v.9
no.3
/
pp.86-90
/
2014
A DC-DC Converter operates in CCM(Continuous Coundcution Mode), DCM(Discontinuous Conduction Mode), CRM(Critical Conduction Mode). The CRM is boundary between CCM and DCM. If a DC-DC converter is designed to operate in CRM, its inductor volume can decrease and power loss which caused by switch and diode can decrease. In this paper, the DC-DC converter which operates in CRM is applied to a solar array regulator(SAR) for the satellite. The switching frequency of the CRM boost SAR changes according to input and output condition. The switching frequency limit logic is applied to limit the maximum switching frequency. Meanwhile, the small signal transfer function of the CRM boost SAR is simple, so the controller design is also simple. In this paper, the small signal transfer function from control reference to solar array voltage is induced. And the voltage controller is designed based on the small signal transfer function. Finally, the CRM boost SAR is verified by simulation.
The Transactions of the Korean Institute of Power Electronics
/
v.10
no.4
/
pp.403-410
/
2005
This Paper Presents development of solar may shunt switching unit with a fully regulated Power regulation for Geostationary Earth Orbit(GEO) satellite. This shunt switching unit comprises the solar may shunt modules that regulate the solar array power. These solar array shunt modules connect/disconnect the solar array segments to/from the bus through switching actions. And that is also possible simply extension to an existing design by FPGA control logic changing. In order to verify the proposed design, the control logic and worst case analysis are analyzed and the simulation and experimental results we shown.
Park, Chong-Yeun;Jung, Kwang-Hyun;Lim, Byung-Noh;Park, Young-Gil
Proceedings of the KIEE Conference
/
2006.07b
/
pp.966-967
/
2006
본 논문에서는 250W 메탈핼라이드 램프용 전자식 안정기의 구조 및 디밍 방법에 따른 특성을 비교하였다. 측정 및 분석된 안정기는 PFC, 벅 컨버터, Full-bridge 인버터의 3단 구조를 가진 안정기와 PFC, Half-bridge 인버터의 2단 구조를 가진 안정기이다. 3단 구조를 가진 안정기의 경우 벅 컨버터의 듀티 조절하여 출력 전력을 제어하며, 2단 구조 안정기의 경우는 구동 주파수를 조절하여 전력을 제어한다. 본 논문에서는 각각의 전력제어 방식을 통한 램프 디밍 시의 출력의 특성을 측정 및 분석하였으며, 조도 조절 범위는 $100%{\sim}35%$까지 구현하였다.
Journal of the Institute of Electronics and Information Engineers
/
v.51
no.9
/
pp.41-45
/
2014
In this paper, a high-efficiency power amplifier is implemented by using a drain bias control circuit operated at low input power for WPT(Wireless Power Transfer). Adaptive bias control circuit was added to high-efficiency class-E amplifier. It was possible to obtain the overall improvement in efficiency by adjusting the drain bias at low input power. The proposed adaptive class-E amplifier is implemented by using the input and output matching network and serial resonant circuit for improvement in efficiency. Drain bias control circuit consists of a directional coupler, power detector, and operational amplifier for adjusting the drain bias according to the input power. The measured results show that output powers of 41.83 dBm were obtained at 13.56 MHz. At this frequency, we have obtained the power added efficiency(PAE) of 85.67 %. It was confirmed increase of PAE of an average of 8 % than the fixed bias from the low input power level of 0 dBm ~ 6 dBm.
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.30
no.3
/
pp.77-86
/
2002
위성은 일단 한 번 발사하고 나면 운용궤도상에서 수리 및 회수가 거의 불가능하기 때문에 위성에 들어가는 모든 개발 부품들은 완벽한 설계, 충분한 해석, 고 작업도의 제작, 그리고 다양한 시험이 반드시 수반되어야 한다. 위성시스템에서 전자 소자의 신뢰성에 영향을 주는 인자는 다양하다. 과도한 열은 전자소자의 실패를 유발해서 결과적으로는 전체 위성의 실패를 유도할 수 있다. 이 논문에서는 다목적 실용위성 2호의 고전력 소산 전장품의 열부하 완화를 위한 방안을 경우별로 연구 비교하였다. 고전력 소산 전장품의 열부하를 완화하기 위해서는 하우징 두께의 증가가 필요하며, 전력조절기의 다이오드나 트랜지스터처럼 전력소산이 큰 소자에 대해서는 장착위치를 변경하거나 장착 부분의 열전도율을 증가시키는 방법이 필요하다. 또한 전력조절기처럼 장착면이 좁은 경우에는 복사의 영향이 크며, 이러한 전장품의 열부하를 완화하기 위해서는 주위 벽면의 온도를 낮추거나 하우징 표면 방사율을 증가시키는 방법이 효과적임이 알 수 있다.
본 논문은 에너지 저장장치를 태양광 발전 시스템에 적용시에, 필요한 충전 균형회로를 전력조절기와 통합시키는 방법에 관한 것이다. 기존의 방식은 전력조절기와 별도로 충전 균형회로를 이용하게 되는데, 이는 복잡한 구성을 필요로 하고, 단가 상승의 원인이 된다. 본 논문에서는 태양광 전력변환 시스템 제작 단가를 낮추기 위해 태양광 모듈을 저장장치와 함께 직렬형 구조로 구성한 뒤 적절히 결선하여, 태양광 전력조절기를 셀 밸런싱 회로로 사용하는 방법을 제안하며, 이를 48W 하드웨어 제작 및 실험을 통해 검증하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.