• Journal of the Korean Geotechnical Society
• /
• v.18 no.5
• /
• pp.27-35
• /
• 2002

To construct pipe lines, culverts, or other utility lines, temporary slopes formed by excavating the compacted embankment are frequently met with in the field. Ignoring stability analyses for such slopes and applying inappropriate slope inclinations often result in safety problems. In this study, stability of such slopes were investigated considering the influence of anisotropic shear strength of the layered compacted ground. A series of stability analyses were conducted for slopes varying the slope angle and the height, and assuming isotropic and anisotropic shear strength conditions, respectively. The anisotropic shear strength of the compacted soil was determined from the direct shear test for layered soil blocks varying the inclination angle between the horizontal shear surface and the direction of the soil layer. As a result of the analyses, it has been concluded that the appropriate slope inclination f3r a temporary slope could vary in accordance with the consideration of anisotropy. However, the factor of safety as well as the location of the failure surface did not show significant variation.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.6
• /
• pp.393-401
• /
• 2021

In this paper, we proposed a numerical model based on moment-curvature, to evaluate the resistance of reinforced concrete (RC) members subjected to blast loading. To consider the direct shear failure mode, we introduced a dimensionless spring element based on the empirical direct shear stress-slip relation. Based on the dynamic increase factor equations for materials, new dynamic increase factor equations were constructed in terms of the curvature rate for the section which could be directly applied to the moment-curvature relation. Additionally, equivalent bending stiffness was introduced in the plastic hinge region to consider the effect of bond-slip. To verify the validity of the proposed model, a comparative study was conducted against the experimental results, and the superiority of this numerical model was confirmed through comparison with the analytical results of the single-degree of freedom model. Pressure-impulse (P-I) diagrams were produced to evaluate the resistance of members against bending failure and direct shear failure, and additional parametric studies were conducted.

• Composites Research
• /
• v.21 no.2
• /
• pp.1-7
• /
• 2008

Composite materials are currently used in aero-space industry, sport and leisure industry but it has many problems such as mechanical properties deterioration by moisture absorption. In this study, we appraised interlaminar shear strength with specimen that immersed/ immersed-dried in water environment(distilled/sea) during $100{\sim}200$days. In the result, properties degradation of resin part and silan part by moisture absorption is judged early on main cause of interlaminar shear strength, and later destruction of mechanical bonding between silan part and fiber by moisture absorption is Judged later main cause of interlaminar shear strength. In conclusion, the recovery of interlaminar shear strength is judged to difficult due to interfacial destruction by moisture when pass over irreversible by moisture in composite material.

• The Journal of Engineering Geology
• /
• v.17 no.3
• /
• pp.435-443
• /
• 2007

This study shows the prediction of the engineering properties of weathered zone bearing corestones through the engineering geological surveys and the scale model test in the laboratory. The window survey and the observation on the borehole core were peformed on three natural slopes in corestones area in order to analyse the distribution pattern and the geometrical properties of corestones. Natural corestones were crushed and abrased for the scale model test into less than 5 mm in maximum-2mm in average by the scale reduction ratio based on the size of natural corestones and the specimen size. Scale model tests were carried out on soil and plaster model specimens with different corestone content ratio - 0%, 10%, 20%. The direct shear test on soils shows that shear strength is increased by the increase of corestone content ratio. The increase of cohesion is, however, more important factor to the shear strength of soil for 20% corestone content ratio due to interlocking of crushed corestone particles. The plaster model test shows a tendance of increase of UCS and modulus of elasticity with increase of corestone content. The variation ratio of specimen property by change of corestone content ratio in plaster model test was applied to in situ properties in order to estimate the properties of weathered zone bearing corestones. So it could be predicted that the increase of corestone content to 10% and to 20% produce about 18% and 30% UCS's increase respectively.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.13 no.3
• /
• pp.168-177
• /
• 2008

Trafficablility of a miner and potential environmental impacts due to mining activities should be considered in the selection of a commercial manganese nodule mining site. These two factors can be evaluated comparatively with physical properties and shear strength of sea-bed sediments. For the qualitative comparison of potential minig sites in terms of these two factors, physical properties such as water contents, void ratios, porosities, and grain densities, and shear strengths of surface sediments were determined for the three potential manganese nodule mining sites(KR1, KR2, and KR5) in the Korean manganese nodule contract area, northeast Pacific. For the study, sediment samples were collected from 107 stations from 2004 to 2006. The physical properties of surface sediments showed more significant differences between northern(KR1, KR2) and southern(KR5) blocks than between northern blocks(KR1 vs. KR2). Water content, void ratio, and porosity of sediments from KR5 were relatively higher than those from KR1 and KR2. Grain density of sediments from KR5 was relatively lower than those from KR1 and KR2. Shear strengths of the top 10cm sediments were higher in KR1 and KR2, whereas those of the deeper part were highest in KR5 block. Generally, sediments of high water contents are less suspendible than those of the low water contents by benthic disturbances, thus less disturbance is expected in the sediments of high water content by mining activities. In terms of trafficability, the shear strength of sediment below 10 cm deep is more important than shallower part because miner will disturb at least top 10 cm interval of the surface sediments. Base on these results, we conclude that KR5 area will be the best site for commercial mining among three investigated sites in this study.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.12
• /
• pp.57-62
• /
• 2010

In this study, the effect of different silt contents on the shear characteristics of silty sands was evaluated. Two series of triaxial compression tests were performed on the cylindrical specimens of compacted Nakdong river sand with 10% and 30% silt contents under unconsolidated undrained condition. All identical specimens were prepared to compact with same initial water content for five layers and saturated using control panel and then sheared under initial effective confining pressure, 100 to 400kPa. All specimens exhibited a strain softening tendency after failure in stress-strain curves and deviator stresses of specimens with 10% silt content were greater than those of specimens with 30% silt content. Pore water pressures of specimens with 10% silt content were observed negative(i.e. swelling) due to increasing void ratio after failure but those of specimens with 30% silt content were shown only positive. The behavior of compacted cylindrical specimens with low silt content was more dilative than that of high silt content. Peak deviator stresses decreased as increasing silt content and peak pore water pressures increased as increasing silt content.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.229-239
• /
• 2008

This paper compares the load transfer efficiency between precast concrete pavement specimen and typical concrete pavement specimen by means of laboratory and field tests. An experimental method was developed to evaluate the load transfer efficiency of the dowel bars buried in the concrete pocket and grouted with cement mortar. The test results showed that the load transfer efficiency of the specimen for the dowel bars repaired with grout was equivalent to that of the control specimen. In addition, a series of FWD field tests were conducted on the precast pavement to evaluate the joint stiffness. The field test results revealed that the central deflection of the precast slab slightly increased but the load transfer efficiencies at the joints were almost the same as those in the typical concrete pavement slab.

• Resources Recycling
• /
• v.10 no.1
• /
• pp.7-15
• /
• 2001

We can reuse the portion of simple reclamation and the construction by-products. Until now, we have discarded concrete by simply throwing away or dumping in underground. Therefore, we attempted to propose the technical directions for the reuse of waste concrete as the recycled concrete aggregates and concrete structural materials. As a testing result, It is reasonable that standards are substitution of recycled aggregates under 30%, maximum steel ratio, under 70% of balanced steel ratio, under shear span ratio 0.2 for deep beam criteria for safety and Zsutty's equation is reasonable for estimation of factored shear strength

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.3
• /
• pp.9-18
• /
• 2011

This paper presents shear characteristics of a ground improved by sand piles. The sand piles have different length and diameter depending on the depth of a clayey layer. A series of CU triaxial compression tests are carried out on specimens covered with/without soft material which is similar to geotextile. The results show that the shear strength and stress ration increase as the length and the diameter of the sand pile increase. In addition, covering the specimen with the soft material appears to affect those characteristics as well. The increase of cohesion seems to be more remarkable compared to internal frictional angle.

• Tunnel and Underground Space
• /
• v.19 no.4
• /
• pp.339-347
• /
• 2009

Despite the recent improvement in tunnel excavation technique, Tunnel collapse accidents still happen. This paper suggest two typical cases in unconsolidated ground condition. Collapse causes of each case were analyzed by the measurement records and numerical simulation, and then mechanism of tunnel collapse was investigated about each case. From this study, the crucial indicators of tunnel collapse were the variation of shear strain and ground water level, also, tunnel collapse deeply related to how shear deformation around tunnel was developed according to the excavation step.