• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.221-225
• /
• 1999

In this paper, a new type of predistortion linearizer has been studied. It employs a series feedback amplifier with a large source inductance as a predistortion linearizer, which provides positive amplitude and negative phase deviations for input Power and can compensate for AM-AM and AM-PM distortions of power amplifier. This predistortion lineariaer consists of only one CaAs FET, large source inductor, input output matching networks and bias circuits. Because of its simple circuit, the linear can be operated over a broad bandwidth and has good thermal stability The characteristics of this linearizer can be easily tuned using source inductor, its gate bias condition. In fabricated linearizer, the third-order intermodulation distortion(IMD) for main amplifier alone is 10.61dBc, and the $IM_3$ for main amplifier with predistorter is 21.91dBc. Therefore, the $IM_3$ characteristic results an improvement of approximately 11dB.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.710-715
• /
• 2021

Power line signal can show disturbances due to various causes. Typical anomalies are temporary sag/swell of the amplitude, flat topped signal, and harmonic distortions. The disturbances need to be detected and treated properly for the quality of the power signal. In this study, the power disturbances are detected using the inflection points (IP). The inflection points are defined as points where local maxima/minima or the slope changes occur. The power line signal has a fixed IP pattern since it is basically sinusoidal, and it may have additional inflection points if there is any disturbance. The disturbance is detected by comparing the IP patterns between the normal signal and distorted signal. In addition, by defining a cost function, the time instant where the disturbance happens can be decided. The computer simulation shows that the proposed method is useful for the detection of various disturbances. The simple sag or swell signal only shows the amplitude changes at the detected inflection points. However, the flat top signal and harmonically distorted signal produce additional inflection points and large values in the cost function. These results can be exploited for the further processing of disturbance classification.

• The Journal of Engineering Geology
• /
• v.14 no.1
• /
• pp.21-28
• /
• 2004

Three-dimensional (3-D) resistivity inversion including a topographic effect can be considered theoretically to be the technique of acquiring the most accurate image in the interpretation of resistivity data, because it includes characteristic image that the actual subsurface structure is 3-D. In this study, a finite-element method was used as the numerical method in modeling, and the efficiency of Jacobian calculation has been maximized with sensitivity analysis for the destination block in inversion process. Also, during the iterative inversion, the resolution of inversion can be improved with the method of selecting the optimal value of Lagrange multiplier yielding minimum RMS(root mean square) error in the parabolic equation. In this paper, we present synthetic examples to compare the difference between the case which has the toprographic effect and the other case which has not the effect in the inversion process.

• Journal of IKEEE
• /
• v.19 no.3
• /
• pp.335-341
• /
• 2015

Recently a demand for high precision absolute position transducer is increasing in order to control thickness in steel industry. LVDT (linear variable differential transformer) is widely used to measure the absolute position in the linearly moving cylinder under poor factory environment. In this paper we implement the three phase LVDT with a high resolution of one micron and L/D (LVDT to digital) converter. First we designed U, V, and W three phase signaling using FPGA. Second a pulse output algorithm is designed for position information with A and B phase waveforms. Finally the performance is compared with previous sensors. Experiments show that the linearity deviation error is 0.009788 [mm] and the average sinusoidal THD is 0.0751%, which means 2.2% and 33% more improved result than the previous sensors respectively.

• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.219-226
• /
• 2007

An efficient block based two-layer JPEG encoding algorithm is proposed to compress high dynamic range (HDR) images in this work. The proposed algorithm separates an input HDR image into a tone-mapped low dynamic range (LDR) image and a ratio image, which represents the quotients of the original HDR pixels divided by the tone-mapped LDR pixels. Then, the tone-mapped LDR image is compressed using the standard JPEG scheme to preserve backward compatibility and the ratio image is encoded to minimize a cost function that models the perception of each block with different quantization parameters in the human visual system (HVS). Simulation results show that the proposed algorithm provides better performance than the conventional method, which encodes the ratio image without any prior information of blocks.

• The Journal of Korean Institute of Information Technology
• /
• v.15 no.12
• /
• pp.157-164
• /
• 2017

Mobile ECG signal measurement is a technique to measure small signals of several mV, and many studies have been conducted to remove noise including wandering scheme. Removal of the equipotential line noise caused by shaking or movement of the electrode cable is one of the core research contents for the electrocardiogram measurement. In this study, we proposed a modified step-size of combined NLMS(normalized least squares) and DLMS(delayed least squares) adaptive filter to eliminate baseline noise from ECG signals. The proposed method mainly adjusts initial filter step-size to reduce distortion of original ECG signals characteristic after eliminating baseline noise. The modified filter step-size is scaled by filter order size and distortion minimization factor. This method is suitable for portable ECG device with a small processor and less power consumption. This technique also decreases computation time which is essential for real-time filtering. The proposed filter also increase the signal to noise ratio (SNR) compared to conventional NLMS filter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.2
• /
• pp.160-167
• /
• 2009

To detect islanding mode when the grid is being tripped is a major safety issue in the Utility Interactive Photo Voltaic (UIPV) system. In this paper, analytical design method is suggested for AFD & RPV method under IEEE 929-2000 recommended islanding test condition. We have discussed that there is a same point. we injected reactive component of the current by AFD & RPV methods, but the current reference generated is other waveform. Possible if amount of reactive components in this methods are same each method, there is happened same rates frequency variation. To verify the validity of the analytical comparison, this paper presents simulation and experimental results from single phase, 3[kW] inverter for the transformerless UIPV system.

• Geophysics and Geophysical Exploration
• /
• v.22 no.3
• /
• pp.160-167
• /
• 2019

Resistivity inversion result may be distorted if the seepage line fluctuation within central core with the change of reservoir water level as well as the conductivity of the reservoir water is not taken into consideration because the reservoir dike is composed of three-dimensional (3D) resistivity structure. Consequently, to accurately analyze the resistivity changes inside the reservoir dike according to the change of reservoir water level, 3D electrical resistivity modeling for the 2D survey line considering topography and physical properties of dam components was carried out. In addition, 2D inversion was performed with the simulated 2D resistivity data for a given 3D model in order to compare it with the inversion result of real field data. For 283 reservoirs in Korea, 2D inversion results for the simulated 2D data and field 2D resistivity data were compared. Finally, the reservoirs with an inversion ratio of 50% or less were selected as reservoirs that require further precise investigation.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.3
• /
• pp.279-292
• /
• 2022

Unexpected anomalies in the geotechnical investigation at design stage may cause problems during tunnel excavation. Therefore, it is important to predict the ground condition ahead of a tunnel face during tunnel excavation in order to prevent tunnel collapse. Despite the fulfillment of an electrical resistivity survey at the tunnel face, the existing electrical resistivity survey program can produce distorted results by the limitation of tunnel modelling. In this background, this study develops a modelling program for an electrical resistivity survey considering the tunnel shape. Numerical simulation and inverse calculation were performed for the electrical resistivity survey in the tunnel using the developed program. As a result, it was proved that the developed program could predict accurately the anomalous object's location and condition ahead of the tunnel face.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.61-69
• /
• 2003

Cellular network을 이용하는 휴대 단말기의 경우 TDMA(GSM, IS-136), CDMA(IS-95) 그리고 WCD-MA 등을 포함해서 년간 약 4억대 정도 생산되고 있고, PAM(Power Amplifier Module)은 단말기 한 대당 1~2개 정도 사용되며, 단말기의 battery 사용시간과 밀접한 관련이 있다. 또한 antenna front-end에 장착되기 때문에, 신호의 왜곡에 의한 인접채널 누설 전력과 harmonic 등 전기적인 규격의 적합성과 ESD, 습기 등 품질 신뢰성 문제에 직접적인 영향을 주는 중요한 부품 중의 하나이다. 이로 인하여 PAM의 핵심 기능을 담당하는 PA IC의 공정 기술과 설계 기술, PAM제조 기술 등의 향상에 대한 많은 연구와 개발이 이루어졌다. 본 고에서는 PAM의 최근 기술 동향과 기능적으로 PAM이 주변 수동 및 능동 부품과 집적화 되고 있는 복합 모듈의 동향에 대해서 기술한다.