• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.4
• /
• pp.123-132
• /
• 2008

Aseries of in-situ tests and ground water level measurements with stone and slug materials had been conducted to find out effect of ground settlement reduction and bearing capacity improvement by the Stone Column method. As the result of the tests, it was proved that the Stone Column method is effective for reduction of ground settlement and improvement of bearing capacity. In addition the ground water level went down without overburden load. These results show that the Stone Column method is effective for an increase in density and resistance to liquefaction. The results of estimation of ground settlement and bearing capacity by general theoretical equation, it show that the Stone Column method increases bearing capacity by 2.7~5.7 times and decreases ground settlement by 2~3.5 times.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.2
• /
• pp.133-141
• /
• 2007

The drag reduction (DR) and heat transfer efficiency reduction (HTER) of nonionic surfactant according to the fluid velocity, temperature and surfactant concentration were investigated experimentally. For this study, several kinds of new surfactant which contains amine-oxide and betaine were developed. And experimental apparatus equipped with two water storage tanks temperature controlled, pumps, testing pipe network, two flowmeters, two pressure gauges, heat exchanger, and data logging system was built. Results showed that existing alkyl ammonium surfactant (CTAC) had DR of $0.6{\sim}0.8$ for $1,000{\sim}2,000\;ppm$ in fluid temperature of $50{\sim}60^{\circ}C$ and had very low DR in fluid temperature over $70^{\circ}C$. And new amino oxide and betaine surfactant (SAOB) had lower DR in fluid temperature of $50{\sim}60^{\circ}C$ compared with CTAC but in fluid temperature of $70{\sim}80^{\circ}C$ DR was $0.6{\sim}0.8$ for 1$1,000{\sim}2,000\;ppm$.

• Explosives and Blasting
• /
• v.39 no.4
• /
• pp.12-21
• /
• 2021

In this study, a series of FEM numerical analyses was conducted to compare the resistance performance of concrete drainage protection facility to blast vibration. Two different types of ㅁ-shaped protection facility, which are suggested in the study, were compared to the traditional ㄷ-shaped one. In the analyses, the vibration resistances of the three protection facilities were evaluated under the varying conditions of the standoff distance from the explosion and charge weight per delay. As a result, it was found that the two proposed types of drainage protection facilities are superior to the traditional one in the vibration reduction performance.

• Journal of the Korea Concrete Institute
• /
• v.22 no.4
• /
• pp.451-460
• /
• 2010

There are many types of remodeling, however, engineers and architectures preferred to merge two or more separate units to one very spacious unit. Performing this type of remodeling, in the case of wall dominant apartments, requires partial removal of structural wall causing a concern of structural integrity. However, there are insufficient studies about partial removal, that is, openings. Presently, ACI standard have no clear way to evaluate the effect of opening on the structural wall. AIJ has the provision about strength reduction factor '$\gamma$'. However, this reduction factor cannot exactly evaluate the reduction effect of openings because this factor '$\gamma$' was determined through the elastic analysis. Therefore, in this study, 2 structural wall specimens were tested and many test results from previous studies were collected. Using these data, this study performed statistical analysis about strength of structural wall which have the opening in wall panel. And this study performed parametric study verifying shear strength reducing effect by opening area. In the results of statistical study, previous reduction factor show very conservative results because this equation did not consider other factors, reinforcement ratio and aspect ratio of openings, which was affect the shear strength of shear walls. Therefore we performed parametric study based on the test data and suggest new equation for shear strength reduction factor '$\gamma$'.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.152-156
• /
• 2016

Wastewater heat recovery heat pump systems use heated wastewater from public baths or factories as the heat pump's heat source. Generally, this system uses a bare tube evaporator. In the heat transfer process from wastewater to refrigerant, thermal resistance is caused primarily by fouling deposits on the outside surface of tube. Fouling directly increases thermal resistance and decreases heat pump efficiency. Thus, it is desirable to eliminate fouling. In this study, we fabricated a fouling mitigation device using a bubbling fluidized bed with cleaning sponge balls in the wastewater bath. Experimental conditions were as follows: $20^{\circ}C$ cold-water temperature, $40^{\circ}C$ wastewater temperature, 100 L/h cold water flow rate, and $0.161m^2$ heat exchanger surface area. Experimental results showed that the thermal resistance of fouling decreased by 56% with the fluidized bed alone and by 86% with both the fluidized bed and cleaning sponge balls.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.376-383
• /
• 2008

Generally a return current plane(RCP) of high speed digital and analog part is partitioned. This is achieved in order to decrease the noise interference between subsystem in PCBs(Printed Circuit Boards). However, when the connected signal line exists between each subsystem, this partition will cause unwanted effects. In a EMI(Electromagnetic Interference) point of view, the partition of the return current plane becomes a primary factor to increase the radiated emission. Component bridge(CB) is used for the way of maintaining radiated emission, still specific user's guide doesn't give sufficient principle. In a view point of EMI, design principle of multi-CB using method will be analyzed by measurement. And design principle of noise mitigation will be provided. Generally interval of multi-CB is ${\lambda}/20$ ferrite bead. In this study, When multi-CB connection is applied, design principle of ferrite bead and chip resistor is proved by measurement. Multi-connected chip resistance$(0{\Omega})$ is proved to be more effective design method in the point of EMI.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.373-379
• /
• 2001

When a train runs into a tunnel at high-speed, aerodynamic drag suddenly increases and the booming noise is generated at the exit of tunnel. The noise shape is very important to reduce the aerodynamic drag in tunnel as well as on open ground, and the micro-pressure wave that is a source of booming noise is dependent on nose shape, especially on area distribution. In this study, the nose shape has been optimized employing the response surface methodology and the axi-symmetric compressible Navier-Stokes equations. The optimal designs have been executed imposing various conditions of the aerodynamic drag and the micro-pressure wave on object functions. The results show that the multi-objective design was successful to decrease micro-pressure wave and aerodynamic drag of trains.

• Journal of the Korean Society of Visualization
• /
• v.14 no.1
• /
• pp.27-32
• /
• 2016

The reduction of $CO_2$ emissions has been a key target in the Marine Industry since the IMO's Marine Environment Protection Committee published its findings in 2009. The representative emission index is termed as the EEDI (Energy Efficiency Design Index) for the new ships. Among various flow control techniques ever proposed, the air lubrication method is the one of most promising one in terms of practical applicability. The present study examines the basic characteristics of the flat plate test with intention of applying the air lubrication technology to the reduction of the resistance of a ship. Image analysis technique is proposed as a tool to quantify the effectiveness of the air lubrication method.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.525-528
• /
• 2011

1400cc급 발전용 엔진 트로틀 바디의 최적화 및 성능 향상을 위하여 유동해석을 수행하였다. 베르누이 정리를 기본으로, 성능을 발휘하는 주요 설계인자인 트로틀 바디 내부의 트로틀 밸브 각도 및 흡기부 곡률 등을 설계 변수로 유동해석을 수행하였다. 벤튜리관 흡입부의 곡률을 증가시켜 트로틀 바디에서 소모되는 흡기저항을 줄였다. 감소된 흡기저항은 펌핑로스를 저감하여 연비향상에 도움이 될 것으로 기대된다. 결과적으로 해석결과 분석을 통하여 최적화된 모델을 제시하였다.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.582-587
• /
• 2016

연료효율에 대한 선주들의 요구와 그린쉽이라는 사회적 흐름에 맞춰 현재 연료 절감 장치에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 KVLCC2M의 반류개선 및 연료효율 증가를 위한 반원형 덕트의 변수 연구를 진행하였으며, 계산의 신뢰도를 검증하기 위해 서울대학교 선박저항성능 연구실에서 실시한 모형 시험결과와 비교하였다. 반원형 덕트의 크기와 길이방향 위치를 설계변수로 설정하여, 총 12가지 경우에 대한 CFD 계산을 시행하였으며, 계산 결과를 유동 정류를 통한 저항 감소와 반류 개선을 통한 프로펠러의 성능 개선 이라는 두 가지 기준으로 최적 조건을 선정하였다. 또한, 후처리를 통해 계산 결과를 추가적으로 분석하여 에너지 절감의 이론적인 배경을 찾았으며, 이를 바탕으로 반원형 덕트를 개선하여 부채꼴형 덕트를 새로이 설계하였다. 이에 대한 추가적인 계산 결과 최대 4%의 연료절감 효과를 최종 확인하였다.