• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.3
• /
• pp.267-272
• /
• 2011

We analyzed the wear characterization of $Si_3N_4$ ceramics according to the amount of added $SiO_2$ nanocolloid. The test specimen was prepared by hot-press sintering at 35 MPa and 2123 K in an $N_2$ gas atmosphere for 1 h. A wear test was performed with a block-on-ring tester, and the test conditions were as follows: (1) the ring with a diameter of 35 mm had a rotational speed of 50 rpm; (2) the load was 9.8 N; and (3) the temperature was $25^{\circ}C$. The test results show that $Si_3N_4$ ceramics have a friction coefficient of about 1.0 and a wear loss of about 0.02 mm. Of the specimens used this study, the test specimen with 1.3 wt% of added $SiO_2$ nanocolloid has the best wear resistance because it has the lowest friction coefficient and the smallest wear loss. This specimen also has the highest Vickers hardness and bending strength. In this study, the friction coefficient is inversely proportional to the hardness and bending strength.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.4
• /
• pp.439-445
• /
• 2001

The destructive method is reliable and widely used lot the estimation of material degradation but, it have time-consuming and a great difficulty in preparing specimens from in-service industrial facilities. Therefore, the estimation of degraded structural materials used at high temperature by nondestructive evaluation such as electric resistance method, replica method, Barkhausen noise method, electro-chemical method and ultrasonic method are strongly desired. Ultrasonic nondestructive evaluation technique has been reported good to attain efficiency of measurement, high sensitivity of measurement, and rapidity and reliability of result interpretation. In this study, it was verified experimentally the feasibility of the evaluation of degraded 2.25Cr-1Mo steel specimens which were prepared by the isothermal aging heat treatment at $630^{\circ}C$ by high frequency longitudinal wave method investigating the change of attenuation coefficient by FFT analysis and wavelet transform. Because of carbide precipitation increase and spheroidization near grain boundary of microstructure to aging degradation, attenuation coefficient had a tendency to increase as degradation proceeded. It was identified possibly to evaluate degradation using the characteristics of high-frequency ultrasonics. Frequency dependence of ultrasonic attenuation coefficient to aging degradation appeared large, which made sure that attenuation coefficient is an important parameter for evaluation of aging degradation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.1
• /
• pp.83-91
• /
• 1994

We have constructed a vertical gradient freeze (VGF) grower for GaAs single crystals 2 inch in diameter and have grown semi-insulating GaAs co-doped with Cr and In. For the co-doped crystal, the segregation coefficients of the dopants remain unchanged when compared to those doped with only Cr or In. The concentration of Cr and in atoms range from about $2{\Times}10_{16} to 3{imes}10^{17} cm^{-3}$ and $2{\Times}10^{19} to 3{\Times}10^{20} cm^{-3}$ at the seed to the tail part of the grown crystal, respectively. The averaged dislocation etch pit density is found to be less than $8000 cm^{-2}$ throughout the ingot. It is also found that there is some evidence of lattice hardening for the crystal in which the dislocation density is decreased to less than $1000 cm^{-2}$ as In concentration increases. The resistivity increases abruptly from $10^{-2}$ up to $10^8$ Ohm-cm, while the carrier concentration decreases from $10^{16}$ to $10^8 cm^{-3}$ along the growth direction of the GaAs crystal. Semi-insulating properties can be obtained above a critical concentration of Cr of about $6{\Times}10{^16} cm^{-3}$ in the crystal. The main deep levels existing in the GaAs: Cr,In sample are two electron traps at $E_C-0.81eV, E_C-0.35eV$, and two hole traps at $E_V+0.89eV, E_V+0.65eV$.

• Polymer(Korea)
• /
• v.34 no.3
• /
• pp.191-197
• /
• 2010

To improve the curing method of anisotropic conductive film (ACF) at low temperature, it was studied to replace the thermal latent curing agent of imidazole compounds by the curing agent of cationically initiating type. Thermo-mechanical properties such as glass transition temperature, storage modulus, and coefficient of thermal expansion were investigated for the analysis of curing behavior. The reliability of ACF were observed in thermal cycle and high temperature-high humidity test. ACF using cationic initiator showed faster curing, lower CTE, and higher $T_g$ than the case of using imidazole curing agent, which is important for the high temperature stability. Furthermore, ACF using cationic initiator maintained a stable contact resistance in reliability test, although it was cured at low temperature and fast rate. With these results, it was confirmed that the curing method of epoxy had great effect on thermo-mechanical properties and reliability of ACF.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.4
• /
• pp.33-38
• /
• 2011

The p-type $(Bi_{0.2}Sb_{0.8})_2Te_3$ powers were fabricated by mechanical alloying and hot-pressed at temperatures of $350{\sim}550^{\circ}C$. Themoelectric properties of the hot-pressed $(Bi_{0.2}Sb_{0.8})_2Te_3$ were characterized as a function of the hot-pressing temperature. With increasing the hot-pressing temperature from $350^{\circ}C$ to $550^{\circ}C$, the Seebeck coefficient and the electrical resistivity decreased from 237 ${\mu}V/K$ to 210 ${\mu}V/K$ and 2.25 $m{\Omega}-cm$ to 1.34 $m{\Omega}-cm$, respectively. The power factor of the hot-pressed $(Bi_{0.2}Sb_{0.8})_2Te_3$ became larger from $24.95{\times}10^{-4}W/m-K^2$ to $32.85{\times}10^{-4}W/m-K^2$ with increasing the hot-pressing temperature from $350^{\circ}C$ to $550^{\circ}C$. Among the specimens hot-pressed at $350{\sim}550^{\circ}C$, the $(Bi_{0.2}Sb_{0.8})_2Te_3$ hot-pressed at $500^{\circ}C$ exhibited the maximum dimensionless figure-of-merit of 1.09 at $25^{\circ}C$ and 1.2 at $75^{\circ}C$.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.10
• /
• pp.881-887
• /
• 2014

Micro-sized Peltier coolers are generally employed for uniformly distributing heat generated in the multi-chip packages. These coolers are commonly classified into vertical and planar devices, depending on the heat flow direction and the arrangement of thermoelectric materials on the used substrate. Owing to the strong need for evaluation of performance of thermoelectric modules, at present an establishment of proper theoretical model has been highly required. The design theory for micro-sized thermoelectric cooler should be considered with contact resistance. Cooling performance of these modules was significantly affected by their contact resistance such as electrical and thermal junction. In this paper, we introduce the useful and optimal design model of small dimension thermoelectric module.

• Journal of the Korean Chemical Society
• /
• v.53 no.2
• /
• pp.175-188
• /
• 2009

In this study, we developed an experimental method of the Charles' law applicable to school. Science textbooks and literatures on this principle were analyzed to extract factors utilized in organizing the experimental setup and method. A combined structure such as with a vial and a glass tube, the former of which is for deciding the total volume and the latter of which is for easy measurement of volume, was better in measurement of volume with temperature rather than a simple structure such as syringe. Use of graduated cylinder as a water bath to control the temperature showed advantage in cooling time than using other bath of larger volume such as a beaker. A liquid drop was used as a plug in the glass tube. This plug has little resistance with the glass wall when the gas volume changes. Water as a liquid drop in the glass tube had a significant effect in volume change of gas due to evaporation, especially in the beginning of the measurement. Glycerol showing negligible effect in volume change was used. This method took about one hour and produced a good linear relationship between the temperature and volume of gas with $R^2$ = 0.999 and absolute zero temperature = $-216.7\;{^{\circ}C}$. The Charles' law experiment developed in this study can be performed with appropriate adjustment of procedure considering the purpose of the curriculum of science and chemistry subject at each school level.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.71.2-71.2
• /
• 2010

고체산화물연료전지는 청정에너지원으로써 기존의 발전방식을 대신할 차세대 에너지원으로 각광 받고 있다. 고체산화물 연료전지는 고온에서 작동하는 특성상 실험을 통하여 전극미세구조 및 구동조건을 최적화하는 것은 매우 어렵다. 본 연구는 전기화학식을 이용한 전산모사를 통해서 고체산화물 연료전지의 구동조건에 따른 성능 평가 및 전극의 미세구조 최적화 과정을 수행하였다. 전극 내 전달현상을 무시하고 오직 전기화학반응만을 고려한 전산모사는 단전지의 전극미세구조 및 구동조건에 따른 전지성능을 빠르게 예측할 수 있으며, 이를 기반으로 다양한 조건에서 얻은 전지 성능 데이터를 통해 전극미세구조를 최적화하였다. 개회로전압, 활성화분극, 저항분극, 물질수송손실을 표현하기 위하여 Nernst 식, Butler-Voler 식, 옴의 법칙, dusty-gas 모델을 각각 사용하였으며, 전극미세구조 및 구동조건의 변화는 물질확산계수 및 교환전류밀도를 통하여 그 영향이 전지성능에 반영된다. 온도, 압력, 주입 연료의 조성에 대한 성능평가가 수행되었으며, 1023K, 1 bar의 조건하에서 최적의 단전지 성능을 위한 기공도와 기공크기를 조사하였다. 더 향상된 단전지 성능 확보를 위해서 실험에서 쓰이는 기능층(functional layer)과 유사하게 넓은 반응 면적과 원활한 반응물 및 생성물의 이동을 보장하도록 기공도 및 기공크기를 그레이딩한 전극구조(graded-electrode)를 디자인하고 성능을 평가하였다. 그 결과 기존의 전지구조 대신에 그레이딩된 전극을 사용할 경우 50%이상 향상된 전지성능을 예측할 수 있었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.3
• /
• pp.127-132
• /
• 2014

$Y_2O_3$-BN ceramic composites were fabricated from the slurries of yttria powder with average particle size of 3~10 ${\mu}m$. The slurry was fabricated by mixing PVA binder, NaOH for Ph control, PEG, BN powder and $Y_2O_3$ powder. The mixed $Y_2O_3$ powders were obtained by spray drying process from the slurry. The $Y_2O_3$-BN composite specimen was shaped in size of ${\O}14mm$ and then sintered at $1550^{\circ}C$ and $1600^{\circ}C$, respectively. The characteristics, microstructure, purities, densities, bulk resistance, thermal expansion, hardness and plasma resistance of the $Y_2O_3$-BN composites were investigated with the function of BN contents and sintering temperature.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.203-209
• /
• 2010

The base asphalt mixtures that used the waste recycle asphalt correcting from the four different overlay construction sites in Seoul city were made using the foamed asphalt method. The sample mixtures were made in different ratio of the recycle asphalt and new asphalt material and the performance of the mixtures of the different ratio was investigated in the laboratory. The laboratory tests includes the Marshall test, the indirect tensile test, the resilient modulus test, the creep test and the wheel tracking test. The test of the recycle foamed asphalt mixtures(RFA) were compared with the those of the recycle hot mix asphalt(RHA) mixtures. The performance of the RFA is comparable to that of the RHA. On the other hand, the indirect tensile strength of the RFA in dry condition is lower than that of RHA and the indirect tensile strength of the RFA in wet condition is much lower than that of the RHA.