• Electrical & Electronic Materials
• /
• v.6 no.1
• /
• pp.69-79
• /
• 1993

ZnO 바리스터는 전기전자 장치에 비이상적인 써어지 혹은 잡음신호가 침입하는 것을 막기위해서 폭넓게 사용되고 잇다. 많은 연구자들은 저전압 바리스터를 제조하기 위해서 요러가지 방법을 제시하였다. 그렇지만 그러한 방법들은 6V이하의 동작 전압을 갖는 바리스터를 제조하기는 어렵다. 본 연구에서는 새로운 3-성분 종입자법으로 제조한 바리스터의 전도특성을 보고하고자 한다. 온도범위 20-150.deg.C 및 전류 범위 $10^{-8}$~$10^{-1}$A/$cm^{2}$에서 관찰된 바리스터의 전도특성은 측정전류가 증가함에 따라서 다른 기구를 갖는 3개의 영역으로 구분되었다. 측정전류가 $10^{-3}$ A/$cm^{2}$이하인 경우에 오옴전도 혹은 누설전류 영역으로 해석 할 수 있었다. 측정 전류가 $10^{-3}$ A/$cm^{2}$ 부근에서는 이중 쇼트키 장벽에 의한 전도로 해석할 수 있었으며 또한 $10^{-3}$ A/$cm^{2}$ 이상의 전류 영역에서는 턴넬 전도 전류로 해석 할 수 있었다. 이상의 결과로 부터 3-성분 종입자법으로 저전압 바리스터를 제조하는 방법은 지금까지 보고된 어느 다른 방법보다도 우수하며 그 전도기구를 제시하였다.

• Electrical & Electronic Materials
• /
• v.9 no.10
• /
• pp.1019-1026
• /
• 1996

In this study, we may be presented the carrier oscillation properties for the low-voltage varistor fabricated by a new method of three composition seed grain, in order to analyze the behavior of carriers at the its equivalent circuit model. The oscillation phenomena of carriers appeared from current-voltage characteristics under knee voltage is shown by the transient flow of nontrapped carriers group in the trap level of intergranular layer, surface state and/or depletion layer. In particularly, current oscillation phenomena is hardly shown in the high electric field. It is that the injected carriers from both electrodes are directly from the conduction band of forward biased ZnO grain through the intergranular layer into the reverse biased ZnO grain, because the trap level in the electric field above the knee voltage is mostly filled.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.4
• /
• pp.793-801
• /
• 2000

This paper presents the effect of lightning impulse current on ZnO varistors(390[V], 6.5[kA]) used in low-voltage AC mains as a protective device against transient overvoltages. The electrical characteristics of ZnO varistors are deteriorated by overtime impulse current, and a deteriorated ZnO varistor is brought to a thermal runaway and finally destroyed even in normal operating voltage. Therefore, it is important to estimate the changes of the electrical characteristics of ZnO varistors. A lightning impulse current standardized in IEC 61000-4-5 is applied to the varistors to accelerate deterioration, and the energy applied to the varistor at each time is about 12 [J]. In the experiment, various parameters such as leakage current, reference voltage are measured with the number of applied impulse current. Also, micro-structure changes of the varistors after applying the lightning impulse current of 200 times are compared. The electrical characteristics of the varistors are degraded by overtime impulse current, showing increase in leakage current and decrease in reference voltage.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.3
• /
• pp.95-100
• /
• 1990

We fabricated primary and secondary seed grains. Primary seed grains having larger grain size were obtained under the conditions that were 2.0mol.% $BaCO_3$ and 10 hours sintering. The amount of primary seed grain that yield the largest secondary seed grain was chosen as 3wt.% and we fabricated the low voltage varistors which were jointed the low voltage-oriented ZnO varistor system made by conventional method with the secondary seed grains. As a result, the ZnO varistors under those conditions showed approximately 10V/mm of nonlinear resistance and 15-22 of nonlinear exponent.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.6
• /
• pp.986-991
• /
• 1987

To establish the basic composition of low voltage varistor and to find the role of each compont in detail, we investigated the electrical properties and the microstructures. As a result, ZnO 1.0m/oBi2O3-1.0m/oCo2kO3-0.2m/oMnO2 system was optimum for low voltage varisor. We found that Bi2o3 promotes grain growth of ZnO and that Co2O3 doped in ZnO grain lowers the nonlinear resistance and MnO2 mainly existed near the ZnO grainboundary elevates nonlinear resistance.

• Journal of the Korean Ceramic Society
• /
• v.27 no.4
• /
• pp.473-480
• /
• 1990

Low-voltage ZnO-based varistors were made by seed grain method at various sintering conditions. Their microstructure and electrical properties were investigated and comlpared with those of the ZnO varistors made by a conventional method at the same sintering condition. During the sintering process, the added seed ZnO grain rapidly grew to be a gaint grain(above 500$\mu\textrm{m}$) provinding easy current path. Therefore the breakdown voltage was lowered as much as the order of 1/10-1/5 in comparison to that of the varistor made by a conventional method. But the grain size of the giant ZnO was little influenced by sintering condition, so the breakdown voltate was also little influenced. The weight loss was decreased by the addition of the seed grain, because the giant grain decreased the evaporation area. Therefore the nonobmic property of the specimen made by seed grain method was little influencedby sintering condition. In this research the low-voltage varistor made by seed grain method showed the least leakage current when sintered at 1150$^{\circ}C$ for zero hour.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.8
• /
• pp.1211-1216
• /
• 1989

To enhance the breakdown properties of low voltage-oriented ZnO varistor, sample were fabricated with additive oxides and sintering conditions. Addition of TiO2 lowered breakdown voltage` nonlinear resistances were lowered about 10V/mm and nonlinear exponents were not lowered with respect to it with the basic composition. To the samples added TiO2, V2ko5, and Cr2O3, microstructures were observed by SEM, moreover Ti was detected at grainboundaries and within the grain by EDS. Addition of Si-oxides and Sb2O3 increased nonlinear exponent and also increased nonlinear resistance, by addition of TiO2 to these samples at the sintering conditions of 1250\ulcorner and 1 hour we could fabricate low voltage-oriented ZnO varistors with nonlinear exponent of 30 or more and with real breakdown voltage of 30V/mm.