• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.3
• /
• pp.713-722
• /
• 1991

본 연구에서는 graphite/epoxy와 glass/epoxy 그리고 graphite/epoxy와 kevl- ar/epoxy의 혼합적층된 복합재료 평판의 저속충격에 대한 응답을 유한요소 모델을 사 용하여 수치해석 한후, 각각의 단일적층판들의 결과와 비교하였으며, 이때의 접촉력 관계식은 Yang과 Sun이 제안한 수정된 접촉법칙을 이용하였다. 또한, 수치해석 결과 에서의 충격자의 속도변화로써 혼합적창판 배열에 따른 에너지 흡수율을 계산하였고, 이를 충격특성이 취약한 graphite/epoxy 단일 적층판의 결과와 비교 고찰하였다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.574-577
• /
• 2010

이번 연구에서는 저속 비압축성 유체-구조 연성을 고려한 위상 최적화을 위해 새로운 모노리틱 해석을 개발한다. 이 새로운 해석 기법에서는 기존의 유체-구조 연성 시스템 해석 기법에서 유체와 구조 영역을 분리하고 연성 조건을 만족시키는 것과 다르게 하나의 일치된 해석 방정식을 유체 영역과 구조 영역에 동일하게 적용한다. 또한, 경계조건을 만족시키기 위하여 단일화 된 해석 방정식의 물성치를 바꾸어주는 새로운 방식을 제시하였다. 이 새로운 방법에서는 유체, 구조 영역을 분리하지 않고 Navier-Stoke's 방정식과 선형 탄성식을 동시에 사용하였다. 또한, 유체-구조 영역이 연성 해석 중 변화하는 것을 반영하기 위하여 구조 변위를 이용하여 Deformation tensor를 계산하였고 이를 이용하여 변형 후에서의 Navier-Stoke 방정식의 미분을 계산하는 방법을 제안하였다. 그리고, 정상 상태 유체를 가정하고 속도에 비례하는 마찰힘인 Darcy's force 항을 Navier-Stoke 방정식에 넣고 이 마찰 힘의 크기를 변화시킴으로 해서 유체 방정식에서의 연성 경계 조건을 만족시켰다. 선형 탄성 방정식에서 Divergence이론을 이용해서 경계에서 작용하는 외력이 하는 일을 내부 시스템에 하는 일로 계산하였다. 개발된 모노리스 해석 방법을 이용하여 저속 비압축성 유체가 구조에 미치는 압축력을 계산하였고 이용하여 컴플라이언트 미케니즘을 설계하였다.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.320-322
• /
• 2010

저용량 에어컨의 압축기에 많이 사용되는 Single rotary 방식은 하나의 피스톤만을 채용하여 가격적인 면에서 큰 이점을 가진다. 그러나, 압축기 모터가 1회전할때 마다 압축과 토출을 단 1회 거치게 되므로, 부하변동을 심하여 진동이 많이 발생하는 단점이 있다. 이러한 단점을 보완하기 위하여 Single rotary를 사용하는 에어컨 제품에서는 저속에서의 운전을 회피하거나 하나의 운전점에 대한 전향보상기를 채용하여 진동을 저감시켜 왔다. 본 논문에서는 모든 운전점에서 보상이 가능하도록 압축과 토출로 인한 부하의 패턴에서 각 주파수 성분을 분석하여 자동으로 부하 토크를 보상하는 알고리즘을 제안한다. 제안된 방법은 가장 영향이 큰 1차와 2차 주파수 성분의 속도 리플의 양을 FFT 하고, 그 양이 작아지는 방향으로 부하 토크를 전향 제어방식으로 인가하는 방식이다. 제안된 방식을 이용하여 저속 운전에서 진동이 저감 되는것을 실험을 통하여 보였다.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.1
• /
• pp.49-56
• /
• 2011

The neck injury occupies the most of injury that happened by the rear impact car accident. This study was analyzed about influence of the neck injury in low speed rear impact and car crash accident investigation. There is no neck injury in low speed side rear impact. On the other hand, there is initial neck injury symptom of 10 % but no long-term neck injury symptom in low speed offset rear impact. It appeared that the possibility of neck injury in low speed rear impact is low. For the more study about the neck injury, it should be evaluate the effects of the car body structure, frame structure and rear crash pattern.

• Cement
• /
• s.133
• /
• pp.13-17
• /
• 1993

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.2
• /
• pp.131-143
• /
• 2013

Vibration condition monitoring of low-speed rotational slewing bearings is essential ever since it became necessary for a proper maintenance schedule that replaces the slewing bearings installed in massive machinery in the steel industry, among other applications. So far, acoustic emission(AE) is still the primary technique used for dealing with low-speed bearing cases. Few studies employed vibration analysis because the signal generated as a result of the impact between the rolling element and the natural defect spots at low rotational speeds is generally weak and sometimes buried in noise and other interference frequencies. In order to increase the impact energy, some researchers generate artificial defects with a predetermined length, width, and depth of crack on the inner or outer race surfaces. Consequently, the fault frequency of a particular fault is easy to identify. This paper presents the applications of empirical mode decomposition(EMD) and ensemble empirical mode decomposition(EEMD) for measuring vibration signals slewing bearings running at a low rotational speed of 15 rpm. The natural vibration damage data used in this paper are obtained from a Korean industrial company. In this study, EEMD is used to support and clarify the results of the fast Fourier transform(FFT) in identifying bearing fault frequencies.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.700-707
• /
• 2016

Recently, ammunition malfunctions of the 40mm grenade were reported during live fire training. When 72 40mm grenades were fired by the army, 11 duds were encountered. The dud ammunition rate was approximately 15%. Because ammunition is used a long time after its manufacture, it is necessary to ensure its performance after long-term storage. In this study, we attempted to decrease the dud ammunition rate of 40mm grenade (K200) fuzes through quality improvement. First, it was determined by the detonator performance test that abnormal explosions occurred due to the degradation of the detonator as a result of its aging characteristics. Second, we improved the fuze quality of the 40mm grenade. Third, we tested its shelf life to estimate its life expectancy. The shelf life of the 40mm grenade fuze obtained using the Arrhenius equation was 6.5 years for the existing grenade fuze and 45.5 years for the improved grenade fuze. This showed that the shelf life of the improved grenade was increased approximately 7 times. Therefore, the improved 40mm grenade fuze contributes to the quality improvement of the 40mm grenade by decreasing the dud ammunition rate during long term storage.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.9
• /
• pp.713-718
• /
• 2015

The purpose of this study is to realize compressor-performance improvements in the fuel economy of an automotive air-conditioning system. We conduct cooling performance tests in a compressor calorimeter test stand. To improve the cooling performance, we investigate the increase in the suction flow rate and the decrease in the discharge dead volume. Based on the results of the test, we found that the cooling capacity and the coefficient of performance (COP) of the compressors were improved as follows. The cooling performance improved greater at high speeds than low speeds in the case of an increase in the suction flow rate increase, and it improved more at low speeds than at high speed when there was a decrease in the discharge dead volume. When both of the above factors were included, we observed that the improvement effects were generally balanced for both high- and low-speed modes, and there was a significant improvement in the discharge temperature. The improvement was found to be about 3.2% at low speed, 8.3% at high speed during in cooling performance improvement, about 5.8% at low speed and about 6.2% at high speed in COP improvement, and there was a decrease of about $3^{\circ}C$ at low speed and a $5^{\circ}C$ decrease at high speed in discharge temperature.

• Geophysics and Geophysical Exploration
• /
• v.21 no.1
• /
• pp.26-32
• /
• 2018

The Northeast China is an important site geologically and geophysically because of a huge volcano called Mt. Baekdu, which is one of the largest volcanoes in the world. Signs of eruption have been recently observed and people are keen to its behavior. We carried out relative travel time tomography to investigate the velocity structure between 100 ~ 600 km depth beneath Northeast China. We used teleseismic data during 2009 ~ 2011 recorded in NecessArray provided by IRIS (Incorporated Research Institute for Seismology). The relative observations were obtained by using the multi-channel cross-correlation method. Based on the tomographic results, we observed that the locations beneath which low-velocity zones are observed coincide with the locations of several volcanic regions in Northeast China. A low-velocity anomaly is revealed beneath Mt. Baekdu down to 600 km depth, which is thought to the main origin of the magma supply for Mt. Baekdu. Another low velocity anomaly is observed beneath east of the Datong volcano down to around 300 km depth, which is inferred to be related to an upwelling from deep mantle. We observed a low velocity anomaly beneath the Wudalianchi volcano down to around 200 km depth, which may imply that this volcano has been formed by an upwelling from the asthenosphere.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.5
• /
• pp.124-134
• /
• 2011

To make popular the NEV(Neighborhood Electric Vehicles) uses, it must be considered the supply of infrastructure and the political decision for NEV. However, the guidelines of infrastructure for NEV are not prepared. The guidelines of infrastructure for NEV should be performed in many research and case. The purpose of this study is to reveal the influence of NEV on the two-lane highway traffic flows by TWOPAS simulation model. The main items to check the influence are Average Travel speed, Percent Time Spent Following and Total Delay. The scenario were setup by traffic volume. And the NEV percentages are changed from 1% ~ 30%. The scenario 1 which traffic volume are 650veh/h and the scenario 4 which traffic volume are 2,600veh/h are less influenced by NEV, compare to scenario 2, scenario 3. Because the scenario 1 is more free to make passing other cars and Scenario 4 is fully saturated with existing traffic volumes. The urban two-lane highway which has much traffic volume and the rural two-lane highway which has little traffic volume has affinity for NEV than the other two-lane highway.