• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.3
• /
• pp.516-526
• /
• 2004

Polymerization shrinkage of photoinitiation type composite resin cause several clinical problems. The purpose of this study was to evaluate the shrinkage strain stress, linear polymerization shrinkage, compressive strength and microhardness of recently developed composite resins. The composite resins were divided into four groups according to the contents of matrix and filler type. Group I : $Denfil^{TM}$(Vericom, Korea) with conventional matrix, Group II : $Charmfil^{(R)}$(Dentkist, Korea) with microfiller and nanofller mixture, Group III : $Filtek^{TM}$ Z250(3M-ESPE, USA) TEGDMA replaced by UDMA and Bis-EMA(6) in the matrix, and Group IV : $Filtek^{TM}$ Supreme(3M-ESPE, USA) using pure nanofiller. Preparation of acrylic molds were followed by filling and curing with light gun. Strain gauges were attached to each sample and the leads were connected to a strainmeter. With strainmeter shrinkage strain stress and linear polymerization shrinkage was measured for 10 minutes. The data detected at 1 minute and 10 minutes were analysed statistically with ONE-way ANOVA test. To evaluate the mechanical properties of tested materials, compressive hardness test and microhardness test were also rendered. The results can be summarized as follows : 1. Filling materials in acrylic molds showed initial temporary expansion in the early phase of polymerization. This was followed by contraction with the rapid increase in strain stress during the first 1 minute and gradually decreased during post-gel shrinkage phase. After 1 minute, there's no statistical differences of strain stress between groups. The highest strain stress was found in group IV and followed by group III, I, II at 10 minutes-measurement(p>.05). In regression analysis of strain stress, group III showed minimal inclination and followed by group II, I, IV during 1 minute. 2. In linear polymerization shrinkage test, the composite resins in every group showed initial increase of shrinkage velocity during the first 1 minute, followed by gradually decrease of shrinkage velocity. After 1 minute, group IV and group III showed statistical difference(p<.05). After 10 minutes, there were statistical differences between group IV and group I, III(p<.05) and between group II and group III(p<.05). In regression analysis of linear polymerization shrinkage, group II showed minimal inclination and followed by group IV, III, I during 1 minute. 3. In compressive strength test, group III showed the highest strength and followed by group II, IV, I. There were statistical differences between group III and group IV, I(p<.05). 4. In microhardness test, upper surfaces showed higher value than lower surfaces in every group(p<.05).

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.281-290
• /
• 2011

We analyzed the basic characteristics and adsorption property of carbonized materials from thinning byproducts of major Korean wood species for evaluating as charcoal making raw material. Yield of charcoal was decreased with increasing the carbonization temperature for all wood species. Refining degrees was 9.0 at $400^{\circ}C$, 3.3~5.0 at $600^{\circ}C$ and 0 at $800^{\circ}C$, and was no difference among wood species. With increasing the carbonization temperature, the fixed carbon content was also increased, and charcoal from softwoods had more fixed carbon content than that from hardwoods. Specific surface area was increased with increasing the carbonization temperature, softwood charcoal had more specific surface area than that of hardwood. Pinus rigida showed the highest specific surface area. In formaldehyde removal by charcoal, some materials had highest at $600^{\circ}C$ and the others had highest at $800^{\circ}C$. Pinus koraiensis, Qurcus acutissima and MDF showed maximum formaldehyde removal ability at $600^{\circ}C$. Ethylene gas removal ability of charcoal was increased with increasing the carbonization temperature, and the charcoal from Pinus rigida and Robinia pseudoacacia had higher ethylene gas removal ability than the other species.

• Applied Chemistry for Engineering
• /
• v.9 no.6
• /
• pp.894-900
• /
• 1998

An interphase between carbon fiber and epoxy matrix was introduced to increase impact strength of carbon fiber reinforced composites (CFRC) without sacrificing the interlaminar shear strength. Flexible polymers, I. e., MVEMA (poly(methyl vinyl ether-co-maleic anhydride)) and EMA(poly(ethylene-co-maleic anhydride)), which have reactive functional groups were considered as interphase materials. Weight hain of MVEMA and EMA onto the surface of carbon fibers was evaluated by changing the parameters of electrodeposition process. Electrodeposition mechanism of polymers which have anhydride functional group was identified by IR spectroscopy, that is, the generation of $RCOO^-$ functional group by the attack of hydroxide anion in the basic solution was observed. The weight gain was increased by increasing concentration of polymers, current density, and electrodeposition time. However the excess generation of oxygen gas decreased the weight gain by removing the deposited polymers. Washing in the running water easily removed the deposited polymers which are on the fiber surface without bonding, as a results, only 0.5 wt% of deposited polymers are remained.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.47 no.3
• /
• pp.320-326
• /
• 2020

The aim of this study was to compare compressive strength and microhardness of recently introduced alkasite restorative materials with glass ionomer cement and flowable composite resin. For each material, 20 samples were prepared respectively for compressive strength and Vickers microhardness test. The compressive strength was measured with universal testing machine at crosshead speed of 1 mm/min. And microhardness was measured using Vickers Micro hardness testing machine under 500 g load and 10 seconds dwelling time at 1 hour, 1 day, 7 days, 14 days, 21 days and 35 days. The compressive strength was highest in composite resin, followed by alkasite, and glass ionomer cement. In microhardness test, composite resin, which had no change throughout experimental periods, showed highest microhardness in 1 hour, 1 day, and 7 days measurement. The glass ionomer cement showed increase in microhardness for 7 days and no difference was found with composite resin after 14 days measurement. For alkasite, maximum microhardness was measured on 14 days, but showed gradual decrease.

• Journal of Adhesion and Interface
• /
• v.22 no.2
• /
• pp.63-68
• /
• 2021

Unsaturated Polyester Resin (UPR) is in general used as a resin to prepare for composite materials with reinforcing materials such as glass fibers. UPR, a thermosetting resin, is used in industry to prepare for sheet molding compound (SMC) molding prepreg that has excellent productivity and is advantageous for mass production among various molding methods of composite materials. The fiber-reinforced composite material using UPR as a matrix material is light and has the advantage of excellent physical properties, but it is weak against impact and is fragile. Four types of polyurethane were synthesized and added to UPR resin to overcome the shortcomings.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.54-63
• /
• 2022

This paper is a study on the friction damper, which is one of the seismic reinforcement devices for structures. This study developed a damper by replacing the internal friction material with ultra high molecular weight polyethylene (UHMWPE), a type of composite material. In addition, this study applied a multi-friction method in which the internal structure where frictional force is generated is laminated in several layers. To verify the performance of the developed multi-friction damper, this study performed a characteristic analysis test for the basic physical properties, wear characteristics, and disc springs of the material. As a result of the wear test, the mass reduction rate of UHMWPE was 0.003%, which showed the best performance among the friction materials based on composite materials. Regarding the disc spring, this study secured the design basic data from the finite element analysis and experimental test results. Moreover, to confirm the quality stability of the developed multi-friction damper, this study performed an seismic load test on the damping device and the friction force change according to the torque value. The quality performance test result showed a linear frictional force change according to the torque value adjustment. As a result of the seismic load test, the allowable error of the friction damper was less than 15%, which is the standard required by the design standards, so it satisfies the requirements for seismic reinforcement devices.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.2
• /
• pp.185-191
• /
• 2017

The objective of this paper is to investigate the effect of waste refractory powder(WRP) and desulfurization gypsum(FGD) as activators on the flow properties and the strength development of high volume blast furnace slag mortar incorporating illite(BSM) having adsorption and deodorization. To fabricate the BSMs with 60% of W/B, blast furnace slag are incorporated with 45% and 65%, respectively. WRP and FGD are substituted from 5 to 10%. Test results indicate that the flow is decreased with increase of WRP and FGD, while increase of WRP and FGD enhance the compressive strength due to accelerated reaction of blast furnace slag, The use of illite results in a decrease of compressive strength. pH has increasing tendency until 7days, while it has reduction. In this paper, optimal dosages of WRP and FGD are believed to be around 5% each.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.103-103
• /
• 2000

강한 결정 방향 의존성과 낮은 항정계를 갖는 Bi4Ti3O12 강유전체 박막은 NDRO형 비휘발성 강유전체 메모리 분야에서 매우 유망한 재료이다. 이를 위해서는 실리콘 기판과의 계면조절과 실리콘 기판성에서 고품질의 강유전성 박막을 성장시키는 기술이 필수적이다. MOCVD에 의한 Bi4Ti3O12 의 증착에서는 Bi 성분의 강한 휘발 특성과 낮은 반응성으로 인하여 조성과 두께 등의 조절이 매우 어렵다. 따라서 화학기상증착의 기구를 이해하고 제어하는 기술이 양질의 박막을 얻는데 필수적이다. 본 연구에서는 유기금속 원료 TPB, TIP 과 산소를 이용하여 실리콘 기판위에 Bi4Ti3O12 강유전체 박막을 증착할 때, 증착 변수의 변화에 따른 박막의 증착 거동과 구조적, 전기적 특성을 연계하여 분석하였다. 특히 기판부착력이 낮고 휘발성이 강한 Bi의 특성으로 인한 문제를 개선하기 위하여 TIP원료를 주기적으로 공급, 중단을 반복하는 펄스주입법을 고안하여 그 효과를 살펴보았다. 실리콘 기판위에서 TiO2의 증착속도는 실험온도 영역에서 온도에 따라 변화하지 않는 전형적인 물질 전달에 의해 지배되는 양상을 나타내었다. 반면 Bi2O3 경우에는 50$0^{\circ}C$ 이상에서 급격하게 증착속도가 감소하는 특이한 경향을 나타내었으며 이는 Bi2O3의 높은 휘발성 때문일 것이다. Bi4Ti3O12 박막은 온도증가에 따라 증착속도가 증가한 후 $600^{\circ}C$ 이상에서 포화되는 경향을 보였다. 이로부터 실리콘 기판위에서의 Bi4Ti3O12 박막의 증착 모델을 제시하였다. Bi2O3에 비해 상대적으로 표면 부착력이 월등히 큰 TiO2가 우선적으로 실리콘 펴면에 형성된 후 TPB 유기금속 원료가 이 TiO2와 반응하는 과정으로 Bi4Ti3O12 박막이 증착된다. $600^{\circ}C$이상에서는 증착 변수들을 바꾸어도 물성이 변하지 않는 자기조절기능이 있음을 알 수 있었는데 이는 고온에서의 Bi2O3의 강한 휘발성 때문일 것이다. 실리콘 기판에서 층상 페로브스카이트 상은 58$0^{\circ}C$ 이상에서 형성되며, 매우 좁은 온도 변화에도 결정구조, 박막현상 및 성분이 크게 바뀌는 온도에 민감한 증착거동이 관찰되었다. 증착 모델에서 예견되는 Bi의 불리함을 개선하기 위해 펄스주입법을 실시한 경우 Bi의 성분량이 증가되었고 결정성이 향상되었다. 이로부터 펄스주입법이 박막내에 부족하기 쉬운 Bi를 보충하여 박막의 특성을 개선함을 확인하였다. Bi4Ti3O12 박막의 증착온도에 따른 누설전류 특성 측정 결과 증착온도가 감소할수록 누설전류가 감소함을 알 수 있었고 펄스주입법이 연속주입법보다 더 낮은 누설전류를 보임을 알았다. 펄스주입법의 경우 -2.5V 인가 시의 누설전류는 7.4$\times$10-8A/cm2에서 1.3$\times$10+7A/cm2의 매우 우수한 값을 가졌다. 연속 주입법에 의해 증착된 박막은 C-V 측정 결과 강유전성 이력이 나타나지 않았으나, $600^{\circ}C$ 이상에서 펄스주입법에 의해 증착된 박박은 강유전성 이력을 나타내었다.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.1 s.129
• /
• pp.29-37
• /
• 2005

The main objective of this research was conducted to evaluate the impacts on the thermoplastic polymer which is a matrix polymer and the rice husk flour (RHF) which is a reinforcing filler relative to the manufacturing temperature and time when bio-composites were manufactured. In order to evaluate the impacts on the rice husk flour relative to the manufacturing temperature, the rice husk flour was persevered for 10 minutes to 2 hours period at $220^{\circ}C$ temperature which was then added with the polypropylene (PP) and low-density polyethylene (LDPE) to complete the manufacturing process of the bio-composites and measure the corresponding mechanical properties. As preserving time increased at $220^{\circ}C$, the tensile and impact strength were decreased due to the thermal degradation of the main components within the rice husk flour. The thermogravimetric analysis (TGA) was used to measure weight loss caused by the actual manufacturing temperature and the result was that the thermoplastic polymer had not scarcely occurred weight change, but there had been increasing rate of weight loss relative to time for the rice husk flour and the bio-composites under the consistent temperature of $220^{\circ}C$ for 2 hour time period. Therefore, the proper manufacturing temperature and time settings are significantly important features in order to prevent the reduction of mechanical properties which were induced throughout the manufacturing process under the high manufacturing temperature.

• Composites Research
• /
• v.34 no.2
• /
• pp.88-95
• /
• 2021

VARTM (Vacuum-assisted resin transfer molding) process is a low-cost process technology and affiliated with OoA (Out of Autoclave). Besides, it has been widely used in various fields. However, because of its lower quality than the autoclave process, it isn't easy to apply the VARTM process to the aerospace industry, which requires high reliability. The main problem of the VARTM process is the loss of mechanical properties due to the low fiber volume fraction and high void content in comparison to the autoclave. Therefore, many researchers have studied to reduce void and increase fiber volume fraction. This study examines whether the method of controlling atmospheric pressure could increase the fiber volume fraction and reduce void during the resin impregnation process. Reliability evaluation was confirmed by compressive strength test, fiber volume fraction analysis, and optical microscopy. As a result, it was confirmed that increasing the atmospheric pressure step by step in the VARTM process of impregnating the preform with resin effectively increases the fiber volume fraction and reduces void.