• Polymer(Korea)
• /
• v.25 no.6
• /
• pp.866-875
• /
• 2001

In this work, thermal decomposition mechanism based on kinetic parameters and thermal stability of carbon fiber-reinforced carbon matrix composites (C/C composites), have been studied under high temperature oxidative conditions with addition of tetra-ethylorthosilicate (TEOS) as an oxidation inhibitor. Thermogravimetric analysis (TGA) was executed to evaluate the thermal decomposition mechanism and thermal stability of C/C composites in the temperature range of 30 ～ $850^{\circ}C$. As a result, the kinetic parameters of the composites impregnated with TEOS, i.e., activation energy for thermal decomposition ($E_d$), order of reaction (n) , and pre-exponential factor (A) were evaluated as 136 kJ/mol, 0, and 2.3$\times$$10^9s^{-1}$, respectively. Especially, the IPDT and $E_d$ of C/C composites impregnated with TEOS were improved largely compared with the composites impregnated without TEOS, due to the formation of $SiO_2$ on composite surfaces, resulting in interrupting the oxygen attack to carbon active site in the composites.

• Composites Research
• /
• v.30 no.3
• /
• pp.223-228
• /
• 2017

The article explains about development of flame retardant self-reinforced composites (FR-SRC) through compression molding technique by utilizing Polypropylene (PP), Ammonium polyphosphate (APP) and chitosan. The effect of APP and chitosan on mechanical, thermal and flame retardant properties in FR-SRC were studied. The mechanical strength of FR-SRC is enhanced than Pure SRC. However, the strength is decreased significantly with increasing the concentration of both flame retardant fillers. But comparison, chitosan filled FR-SRC is stronger than APP filled FR-SRC. In case of flame retardancy, APP is more effective than chitosan. These results can be applicable to provide light weight and recyclable flame retardant self-reinforced composites for automobile and packaging industries, etc.

• Polymer(Korea)
• /
• v.31 no.2
• /
• pp.117-122
• /
• 2007

In this work, the mechanical and electrical properties, and thermal stability of vapor-grown carbon nanofibers/polyimide (VGCNFs/PI) composite film synthesized by in-situ polymerization were investigated in terms of tensile properties, volume resistivity and thermogravimetric analysis (TGA), respectively. From the results, the addition of VGCNFs with a certain amount into polyimide led to obvious improvement in tensile strength. The volume resistivity of the films was decreased with increasing the VGCNFs content and the electrical percolation threshold appeared between 1 and 3 wt% of VGCNFs content, which was probably caused by the formation of interconnective structures among the VGCNFs in a composite system. The thermal stability of the film was higher than that of pure PI one. This result indicated that the crosslinking of VGCNFs/PI Composites was enhanced by well-distribution of YGCNFs in PI resin, resulting in the increase of the thermal stability of the resulting composites.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.450-450
• /
• 2009

최근 전세계적으로 태양전지의 대량보급에 따라 실리콘 원료의 공급에 차질이 생겨 원자재 값이 상승하는 추세에 있다. 결정질 실리콘 태양전지의 제조비용중 실리콘 재료 및 웨이퍼가 차지하는 비율은 약 50~60%정도로 높기 때문에 실리콘 웨이퍼의 두께를 감소시키는 것이 비용절감을 위한 효과적인 방법으로 기대되고 있다. 그러나 실리콘 웨이퍼의 두께가 앓아질수록 제조공정중 균열이나 파손이 발생할 가능성이 높아지기 때문에 이에 따른 실리콘 웨이퍼의 기계적 물성에 대한 연구가 필수적이라 할 수 있다. 본 연구에서는 현재 상용으로 사용되고 있는 크기가 5 인치인 $200{\mu}m$ 두께의 실리콘웨이퍼 (As-saw)를 약 80여개의 시편으로 절단한 후 각각의 파단강도를 부위별로 측정하였다. 또한 표면절단결함을 제거하는 saw damage etching(SDE) 시간을 제어하여 두께가 $150{\mu}m$, $130{\mu}m$인 웨이퍼를 준비하였다. 이들 시험편에 대해서도 부위별 파단강도를 측정하여 as-saw상태의 시험편과 비교하였다. 파단강도 측정은 4 접 굽힘시험을 통하여 측정하였으며 파단면은 주사전자현미경을 통하여 관찰하였다. 또한 실리콘 웨이퍼의 미세균열을 비파괴적으로 검출하기 위하여 100MHz 고주파수를 이용하는 초음파현미경(SAM, scanning acoustic microscope)을 이용하여 균열의 분포를 영상화하였다.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.381-388
• /
• 2002

The properties of polyurethane (PU) nanocomposites with organoclay have been compared in terms of their thermo-mechanical properties, morphology, and gas permeability. Hexadecylamine-montmorillonite ($C_{16}$-MMT) was used as an organoclay to make PU hybrid films. The properties were investigated as a function of organoclay content (1-4 wt%) in the PU matrix. Transmission electron microscopy (TEM) photographs showed that most clay layers were dispersed homogeneously into the matrix polymer in nano-scale, although some particles of clay were agglomerated. We also found that the addition of only a small amount of organoclay was enough to improve the thermal stabilities and mechanical properties of PU hybrid films while gas permeability was reduced. Even at low organoclay content (<5 wt%), the PU nanocomposite showed much better thermo-mechanical properties, and lower gas permeability than pure PU.

• Composites Research
• /
• v.30 no.4
• /
• pp.254-260
• /
• 2017

In this paper, we investigated the application method and properties of 0.1 mm, 0.2 mm and 0.3 mm beads, which can secure a certain thickness due to the molding stability of joint surfaces of different materials (aluminum and composite). In order to verify this, the influence was evaluated according to the thickness of the adhesive in the Double lap test and the FEM simulation. As a result, it was confirmed that as the content of the bead of the adhesive increased more than 1%, the strength of the adhesion increased and the elongation decreased. We confirmed as the size of the bead became larger, the rigidity became lower and the elongation increased.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.320-326
• /
• 2014

The effects of high shear rate processing on the thermal properties of PC/ABS blends were studied. It was executed by the high shear processing machine (NHSS2-28) at the varied conditions of screw speeds and loaded duration. After the samples were processed with NHSS2-28, the $T_gs$ were shifted from 143 to $133^{\circ}C$, and the behavior of degradation determined by TGA showed two distinct steps before high shear rate processing, while it showed a straight line after the processing. In order to provide the reasons of the properties, it was showen by SEM and UTM that the droplet sizes morphologically decreased after the processing, and the elongations decreased slightly until 1000 rpm of screw speed and then sharply decreased, according to the conditions of high shear rate processing. Therefore, it can be confirmed that $T_g,s$ of PC/ABS blends were considerably shifted under an appropriate high shear rate condition, and rapidly dropped, so that blends degraded above the condition, due to stress-induced degradation.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.35 no.8
• /
• pp.1070-1075
• /
• 2006

Food materials for kimchi manufacturing were treated by ozone or gamma irradiation to reduce the number of contaminated microorganisms before the manufacturing of kimchi. Counts of total aerobic bacteria, yeast and mold were $10^6{\sim}10^7 and 10^3{\sim}10^4\;CFU/g$ in the food materials, respectively. After treatment with ozone $(3{\sim}6\;ppm), the total aerobic bacteria were reduced to 1 log cycle or more, in a dose-dependent manner. In comparison, gamma irradiation was superior to ozone treatment. Especially, irradiation of 5 kGy fully eliminated the yeast and mold attached in the food materials for kimchi manufacturing. The contents of ascorbic acid and total and reducing sugar were not affected by ozone or gamma irradiation. Taken together, it is suggested that microorganisms contaminated on materials for kimchi manufacturing could be substantially reduced by ozone (up to 6 ppm) and gamma irradiation (up to 5 kGy), without effect on the nutritional contents.

• Composites Research
• /
• v.14 no.3
• /
• pp.18-31
• /
• 2001

Interfacial and microfailure properties of the modified steel, carbon and glass fibers/cement composites were investigated using electro-pullout test under tensile and compressive tests with acoustic emission (AE). The hand-sanded steel composite exhibited higher interfacial shear strength (IFSS) than the untreated and even neoalkoxy zirconate (Zr) treated steel fiber composites. This might be due to the enhanced mechanical interlocking, compared to possible hydrogen or covalent bonds. During curing process, the contact resistivity decreased rapidly at the initial stage and then showed a level-off. Comparing to the untreated case, the contact resistivity of either Zr-treated or hand-sanded steel fiber composites increased to the infinity at latter stage. The number of AE signals of hand-sanded steel fiber composite was much more than those of the untreated and Zr-treated cases due to many interlayer failure signals. AE waveforms for pullout and frictional signals of the hand-sanded composite are larger than those of the untreated case. For dual matrix composite (DMC), AE energy and waveform under compressive loading were much higher and larger than those under tensile loading, due to brittle but well-enduring ceramic nature against compressive stress. Vertical multicrack exhibits fur glass fiber composite under tensile test, whereas buckling failure appeared under compressive loading. Electro-micromechanical technique with AE can be used as an efficient nondestructive (NDT) method to evaluate the interfacial and microfailure mechanisms for conductive fibers/brittle and nontransparent cement composites.

• Applied Chemistry for Engineering
• /
• v.21 no.2
• /
• pp.217-223
• /
• 2010

In general, fiber-reinforced plastics (FRP) wastes are simply buried or burned. Landfill brings about a permanent contamination of soil due to the inability of FRP to decompose and incineration causes an issue of generating toxic gases and dusts. There have been several ways to treat the FRP wastes such as landfill, incineration, chemical recycling, material recycling and the utilization of energy from combustion. Most methods excluding material recycling are known to have critical limitations in economic, technical and environmental manners. However it is known that material recycling is most desirable among the methods handling FRP wastes. In this study, to investigate the purpose of feasibility of material recycling, various bulk molding compound (BMC) specimens were prepared with the various contents of unsaturated polyester resin binder (25, 30, 35 wt%) and the various replacement ratios of FRP wastes powder (0, 25, 50, 75, 100 wt%) substituted for filler. To evaluate the physical properties BMC specimens, various tests such as tensile strength, flexural strength, impact strength, hot water resistance and SEM imaging were conducted. As a results, mechanical strengths decreased with an increase of replacement ratio of FRP waste powder and physical properties of BMC specimens were deteriorated in the hot water resistance. The fluidity of BMC with more than 50 wt% of the replacement ratio of FRP wastes powder decreased remarkably, causing a problem in the BMC composite.