• Membrane Journal
• /
• v.28 no.1
• /
• pp.37-44
• /
• 2018

Polysulfone composites including graphene were prepared, and their thermal characteristics in membrane states were analyzed by using a custome-made residual stress analyzer and a thermal diffusivity analyzer based on laser flash method. The residual stress analysis was carried out on the polysulfone composite films deposited on Si (100) substrates for 1 cycle of heating and cooling runs. The flat membrane of graphene-embedded polysulfone composites were prepared by the phase transfer method in distilled water and the thermal conductivity was separately measured in the out-of-plane and the in-plane directions. The residual stress of the graphene-embedded polysulfone film was gradually decreased with increasing graphene loading and the out-of-plane thermal conductivity was distinguished from the in-plane thermal conductivity in the flat membranes. These thermal characteristics are caused by the structural uniqueness of graphene and the micro-void structures formed during membrane fabrication.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1982.10a
• /
• pp.29-32
• /
• 1982

본 논문은 광섬유 케이블의 설계에 있어, 케이블 공정에 따른 광손실의 증가를 최소로하는 케이블의 구조 및 광케이블의 포설에 따른 잔류 응력의 억제 등, 장기간 동안 케이블의 전송특성을 유지하며, 광섬유의 파단 방지를 목표로 고려해야할 사항을 논하였다. 광섬유의 특성을 유지하기 위해서는 광섬유 제조시 사용되는 재질 및 적정 Dimension 설정이 필요하며 광섬유 파단 방지를 위해 CABLE내에 TENSION MEMBER를 수용하는 구조를 검토, 광섬유 CABLE 포설시 광섬유의 파단 확률을 감소시키며, 광섬유의 잔류응력을 억제하는 관점에서 케이블 구조를 설계하였다.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1998.11a
• /
• pp.47-52
• /
• 1998

최근에 세라믹-금속 접합, 열차폐코팅(Thermal Barrier Coating), 마모저항코팅등 이종재료접합의 이용이 급증하고 있다. 열차폐코팅의 경우, 고온환경쪽에 세라믹을 배치하여 내열성을 부여하고, 냉각환경쪽은 금속재료를 사용하여 열전도성과 기계적 강도를 부여한다. 이 때 두 재료의 경계부에서는 열적, 기계적 특성 차이로 인하여 제조과정이나 사용중에 열적, 기계적 부하에 의하여 내부잔류응력이 생기게 되며, 이는 재료의 강도, 파괴특성에 많은 영향을 미치기 때문에 잔류응력의 감소기술이 중요시되고 있다. (중략)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.6
• /
• pp.609-615
• /
• 2012

In LSP (laser shock peening) treatment, the laser source geometries when the laser beam strikes the metal target area are diverse. The laser spot geometry affects the residual stress field beneath the treated surface of the metallic materials, which determines the characteristics of the pressure pulse. In this paper, detailed finite-element (FE) simulations on laser shock peening have been conducted in order to predict the magnitude and of the residual stresses and the depth affected in Inconel alloy 600 steel. The residual stress results are compared for circular, rectangular, and elliptical laser spot geometries. It is found that a circular spot can produce the maximum compressive residual stresses near the surface but generates tensile residual stresses at the center of the laser spot. In the depth direction, an elliptical laser spot produces the maximum compressive residual stresses. Circular and elliptical spots plastically affect the alloy to higher depths than a rectangular spot.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.4
• /
• pp.355-360
• /
• 2012

Cold drawn(CD) bars feature superb surface roughness, dimensional precision, and straightness. They are used in the manufacture of automotive parts and home electrical appliances. Two cross-roll straighteners have been used to manufacture CD bars for these industries. This study investigated the variation of the gap size between the two cross-rolls. It was found that changes in the gap size have a large influence on the residual stress and plastic deformation. Finite element method(FEM) simulations were performed to study the influence of the gap size on the residual stress in CD bars, and experiments were performed to verify the FEM results. The residual stresses were measured with X-ray diffraction in both the axial and the hoop directions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.333-338
• /
• 2013

The compressive residual stress and fatigue behavior of shot peened alloy 600 under a high-temperature environment is investigated in this study. Alloy 600 is used in the main parts of nuclear power plants, and the compressive residual stress induced by the shot peening process is considered to prevent SCC (stress corrosion cracking). To obtain practical results, the fatigue characteristics and compressive residual stress are evaluated under the actual operating temperature of a domestic nuclear power plant, as well as a high-temperature environment. The experimental results show that the peening effects are valid at a high temperature lower than approximately $538^{\circ}C$, which is the threshold temperature. The fatigue life was maintained at temperatures lower than $538^{\circ}C$, and the compressive residual stress at $538^{\circ}C$ was 68.2% of that at room temperature. The present results are expected to be used to obtain basic safety and reliability data.

• Journal of the Mineralogical Society of Korea
• /
• v.24 no.3
• /
• pp.189-194
• /
• 2011

Martian satellite missions indicate that Martian equatorial plains are covered by ferric iron oxide. As a non-destructive technique, low-temperature treatment of remanent magnetization is effective in identifying magnetic minerals in rocks. In the present study, four sets of ferric iron oxides were prepared by aqueous alteration of ferrihydrite at warm conditions and four others by dehydration of goethite. As the amount of aluminous trivalent cations increases, crystallographic lattice parameters and N$\acute{e}$el temperatures decrease. Such declines originate from lattice distortion as the smaller aluminous trivalent cations substitue the larger terric irons. Whilst high remanence memory was observed for aqueously produced ferric iron oxide, low remanence memory was observed for dehydrated ferric iron oxide. In the future. magnetic remanence memory would be powerful in diagnosing the origin of ferric iron oxide.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.1-6
• /
• 2011

Pressurized high temperature plastic resin flows into the cavity of mold and is solidified in injection molding process. Residual stress is being developed in injection molded part because of high temperature variations and high pressure. Developed residual stress relaxes as time goes. Consequently this makes part deformed and deteriorates quality of product. A measurement method of residual stress for injection molded transparent articles has been investigated using photoelasticity. Light, a composite of electromagnetic waves, is purified into a single wave by a polarized film. When this wave passes through the specimen, birefringence is developed according to the level of residual stress in the specimen and color fringed pattern appears after the second polarized film. Residual stress in the injection molded transparent flat a part has been measured quantitatively using the color fringed pattern. Optical characteristics have been a part also predicted by computer simulation and compared with experimental results.

• The Journal of Engineering Geology
• /
• v.33 no.4
• /
• pp.717-724
• /
• 2023

Residual shear strength is an important parameter in landslide dynamics and may be considered the critical factor in landslide triggering. Tests were undertaken using Jumunjin sands to examine the effects of smooth and rough surfaces on ring-shear characteristics. Under dense and drained conditions, shear velocities were recorded as 0.01, 0.1, 1, 10, 50, 100 mm s^-1, with shear strength increasing with velocity and producing increasingly fine content. Particle fragmentation may thus increase landslide mobilization when the landslide body is mixed with ambient water in channelized flows.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.39-44
• /
• 2005

Due to mismatch of thermal expansion coefficients between aluminum sheet and glass/epoxy sheet, thermal residual stresses generally appear in the FML. These stresses will affect the yield and fatigue strength of the FML. The numerically determined residual stresses in the Fiber-Metal-Laminates(FML) have been compared to the residual stresses measured from the curvature and tensile test methods. These two experimental methods have been developed for assessing the influence of residual stress in FML. Post-stretching process has been applied to remove the thermal residual stress and reverse the stress distribution. After post-stretching process, the residual stress has been measured from experiments. The results obtained show that analytical and experimental data are well agreed. The thermal residual stress can be removed by post-stretching process and it will increase the yield strength of FML.