• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.251-256
• /
• 2001

Deformation analysis of injection molded articles whose geometry is considered as the assembly of the thin flat plates has been conducted. For the in-mold analysis, thermo-viscoelastic stress calculation of rheologically simple amorphous polymer and in-mold deformation calculation considering the in-plane mold constraint has been done. Free volume theory has been used for the non-equilibrium density state by the fast cooling. At ejection, the redistribution of stress together with instantaneous deformation has been considered. During out-of-mold cooling after ejection, thermoelastic model based on the effective temperature has been adopted for the calculation of deformation. Two typical mold geometries are used to test the numerical simulation.

• 한국재료학회지
• /
• 제6권9호
• /
• pp.878-884
• /
• 1996

본 연구는 가스압소결 질화규소의 혼합모드에 있어서 파괴거동을 실온 및 100$0^{\circ}C$에서 조사하였다. 실험은 누프압흔을 도입한 시험편을 사용하여 소둔처리에 의해 잔류응력을 제거하고, 4점굽힘법을 이용하였다. 실험결과, 종래 제창되고 있는 파괴기준과 일치하지 않고, 그래서 새롭게 4차관수의 근사식을 제안하였다.

• 한국안전학회지
• /
• 제12권2호
• /
• pp.27-36
• /
• 1997

This paper evaluates the static and fatigue bending strengths of CFRP (carbon fiber reinforced plastic) laminates subjected to hygrothermals. The specimens which had different stacking composition, orthotropic and quasi-isotropic laminated plates, were prepared for this experiment. A steel ball launched by the air gun collides against CFRP laminates to generate impact damages, and the 3-point fatigue bending test is carried out by using the impacted laminates to investigate the influence of hygrothermals on the effect on the residual bending fatigue strength of CFRP laminates.

• 대한조선학회논문집
• /
• 제33권3호
• /
• pp.22-34
• /
• 1996

본 논문에서는 선상가열에 의한 평판의 굽힘변형과 관련하여 열탄소성보의 잔류변형과 잔류음력의 분포를 예측하기 위한 간이 수치해석을 시도하였다. 3차원 평판의 거동을 2차원 보의 변형으로 단순화시키기 위하여 수정된 스트립 모델을 사용하고 여기에 유한요소법을 사용하여 시간의 변화에 따른 열탄소성보의 거동을 간편하게 계산할 수 있는 PC용 전산프로그램을 개발하였다. 본 해석에서는 온도장을 구하는 과정은 생략하였고 이미 주어진 온도분포를 사용하여 열변형이 발생하는 문제만을 다루고 있으며 온도에 따른 재료특성치의 변화도 고려하였다. 본 프로그램의 검증을 위하여 계산결과는 기발표된 실험결과나 유사한 방법의 수치해석 결과와 비교하였다.

• 대한기계학회논문집A
• /
• 제22권1호
• /
• pp.238-246
• /
• 1998

Surface residual stresses as well as wall thickness and ovality changes after U-bending process on UNS N06690 row-1 heat exchanger tubes, were estimated. Surface residual stresses were measured by Hole Drilling Method(HDM), calculating the stresses from relieved strains of 3 rosette strain gages. After bending of the tubes, dimensional tolerances for wall thickness and ovality were satisfied with ASTM requirements. Residual stresses at the extrados were introduced with compressive stress(-) by bending operations, and its maximum value reached-319 MPa in axial direction at ${\phi}=0^{\circ}$ in position. Tensile residual stresses(+) of ${\sigma}_zz=45$ MPa,${\sigma}_zz=25$ MPa were introduced in the intrados surface at position of ${\phi}=0^{\circ}$ Maximum tensile residual stress of 170 MPa was detected on the flank side at position of ,${\phi}=95^{\circ}$i.e., at apex region. It appeared that higher stress gradients were generated at the irregular transition regions. In the trend of residual stress changes with U-bend position, the extrados is related with the changes of ovality and the intrados is related with the changes of wall thickness.

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.279-289
• /
• 2000

Residual stress induced in U-bending and tube-to-tubesheet joint processes of PWR's row-1 heat exchanger tube was measured by X-ray method and Hole-Drilling Method(HDM). Compressive residual stresses(-) at the extrados surface were induced in U-bending, and its maximum value reached -319 MPa in axial direction at the position of $\psi$ = $0^{\circ}$. Tensile residual stresses(+) of $\sigma_{zz}$ = 45 MPa and $\sigma_{\theta\theta}$ = 25 MPa were introduced in the intrados surface at the position of $\psi$ = $0^{\circ}$. Maximum tensile residual stress of 170 MPa was measured at the flank side at the position of $\psi$ = $90^{\circ}$, i.e., at apex region. It was observed that higher stress gradient was generated at the irregular transition regions (ITR). The trend of residual stress induced by U bending process of the tubes was found to be related with the change of ovality. The residual stress induced by the explosive joint method was found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the transition region (TR), and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction.

• 대한기계학회논문집A
• /
• 제21권10호
• /
• pp.1541-1550
• /
• 1997

Since the ceramic/metal joint material is made at a high temperature, the residual stress develops when it is cooled from bonding temperature to room temperature due to remarkable difference of thermal expansion coefficient between ceramic and metal. As residual stress at ceramic/metal joints influences the strength of joints, it is important to estimate residual stress quantitatively. In this study, it is attempted to estimate joint residual stress of Si$_3$N$_4$STS304 joints quantitatively and to compare the strength of joints. The difference of residual stress is measured when repeated thermal cycl is loaded, under the conditions of the practical use of the ceramic/metal joint. The residual stress increases at 1 cycle of thermal load but decreases in 3 cycles to 10 cycles of thermal load. And 4-point bending test is performed to examine the influence of residual stress on fracture strength. As a result, it is known that the stress of joint decreases as the number of thermal cycle increases.

• 마이크로전자및패키징학회지
• /
• 제20권1호
• /
• pp.21-26
• /
• 2013

본 연구는 유한 요소 시뮬레이션을 이용하여 계산한 시편의 곡률과 3D 스캐너로 측정한 곡률을 비교하여 패키지 기판 구조의 휨 거동을 예측하는 새로운 분석 방법을 제안한다. 패키지 기판은 프리프레그 경화나 구리 패턴 도금과 같은 다양한 공정을 거치면서 쉽게 휘게 된다. 기판의 휨이 어떤 공정에서 어느 정도 생기는지를 알아보기 위하여 다양한 종류의 시편을 제작하고 각 시편의 형상을 3D스캐너를 이용하여 측정하였다. 그 후 시편의 형상으로부터 film에 걸리는 잔류 응력을 휨을 이용한 수식으로부터 계산하였다. 패키지 기판에 들어가는 절연체는 수지와 서로 직교 존재하는 섬유의 다발로 구성되어 있는 복합재료로서 이방성을 띄게 되는데 이는 패키지 기판의 독특한 굽힘 거동을 일으킨다. 우리는 유한 요소 법에 의한 휨 변형을 시뮬레이션하고 측정 데이터를 이용하여 시뮬레이션 휨을 비교하였다. 측정된 휨으로부터 계산한 전해 구리 도금 응력은 약 58 MPa이다. 솔더 레지스트와 프리프레그의 경화 응력은 각각 실온에서 13 MPa 및 6.4 MPa 정도이다.

• 자원리싸이클링
• /
• 제12권3호
• /
• pp.46-53
• /
• 2003

알루미늄드로스의 재활용은 알루미늄 재생지금 제조시에 요구되는 중요한 사항 중의 하나이다. 본 연구에서는 국내 재생 알루미늄업체에서 발생된 알루미늄드로스를 처리하여 알루미나질 내화물 원료로 재활용하고자 하였다. 드로스 시료를 크기에 따라 선별하고, 1 mm보다 작은 크기의 드로스를 수산화나트륨 용액으로 침출하여 드로스 중의 잔류 알루미늄을 용액 중으로 분리 추출하고, 침출용액에서 석출반응에 의하여 수산화알루미늄을 회수하였다. 드로스 중의 금속알루미늄을 회수한 후 발생된 침출잔사는 수세, 건조, 배소와 같은 일련의 처리를 하여 드로스 중의 잔류 금속성분을 산화물 형태로 변환시켰다. 배소 처리한 드로스 잔사를 골재 및 점결제와 배합하여 알루미나질 캐스타블내화물을 만들고, 굽힘강도와 압축강도를 시험한 결과 KS 기준치인 굽힘강도 $25\;kg/\textrm{m}^2$ 이상, 압축강도 $80\;kg/\textrm{cm}^2$ 이상을 만족하였다. 본 연구결과를 알루미늄드로스를 효율적으로 재활용할 수 있는 한가지 방안으로 제안하고자 한다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 추계학술대회 논문집
• /
• pp.247-252
• /
• 2001

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, two kinds of spring steel (SUP7, 50CrV4) are used. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from on low stress condition, the 1st stage shot peening is not affected by nonmetallic inclusion under metal. it is possible that the 2nd stage shot peening increases the fatigue life and the high stress but that is affected by nonmetallic inclusion under metal. so far beeasily 50CrV4 have made high stress. But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.