• Journal of the Korean Vacuum Society
• /
• v.13 no.4
• /
• pp.157-163
• /
• 2004

Dependence of residual compressive stress of diamond-like carbon (DLC) films on relative humidity was investigated. Polymeric, graphitic and diamond-like carbon films were prepared by r.f.-PACVD using methane or benzene with the negative self bias voltage of the substrate ranging from -100 to -800 V. In-situ measurements of the residual stress were carried out in an environment chamber where the relative humidity was varied from 10％ to 90％. In dense DLC film of high residual compressive stress and hardness, we could not observe any change in the residual compressive stress with relative humidity. However, in the cases of graphitic and polymeric DLC films, abrupt change in the residual stress occurred by changing the relative humidity. The quantity of the stress change was inversely proportional to the film thickness, which means that the stress change with humidity is not due to the penetration of the water molecule into the film structure, but due to surface interaction between water molecules and film surface.

• Proceedings of the KWS Conference
• /
• 1995.04a
• /
• pp.126-129
• /
• 1995

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.26-33
• /
• 2000

In-cylinde flow and mixture formation are key contributors to both idle stability and combustion stability at part load condition in SI engine. The real time measurements of air-fuel ration and in- cylinder residual gas fraction are particularly important to obtain a better understanding of the mechanisms for combustion and emissions especially during cold start and throttle transient condition. This paper reports the cycle resolved measurements of residual gas fraction and equivalence ration near speak plug with value timing change and their effects on combustion characteristics at part load. The results showed that the effect of intake value opening on the residual gas fraction was smaller than that of exhaust valve closing because of the decreases of exhaust gas reverse flow from exhaust port. The variation of equivalence ratio near spark plug increased with the increase of value overlap and it closely related with heat release rate and combustion stability

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.93-100
• /
• 2009

Intake/exhaust valve timing and exhaust cam lift were changed to control the internal exhaust gas recirculation (IEGR) and combustion phase of homogeneous charge compression ignition (HCCI) engine. To measure the IEGR rate, in-cylinder gas was sampled during from intake valve close to before ignition start. The lower exhaust cam made shorter valve event than higher exhaust cam and made IEGR increase because of trapping the exhaust gas. IEGR rate was more affected by exhaust valve timing than intake valve timing and increased as exhaust valve timing advanced. In-cylinder pressure was increased near top dead center due to early close of exhaust valve. Ignition timing was more affected by intake valve timing than exhaust valve timing in case of exhaust valve lift 8.4 mm, while ignition timing was affected by both intake and exhaust valve timing in case of exhaust valve 2.5 mm. Burn duration with exhaust valve lift 2.5 mm was longer than other case due to higher IEGR rate. The fuel conversion efficiency with higher exhaust valve lift was higher than that with lower exhaust valve lift. The late exhaust and intake maximum open point (MOP) made the fuel conversion efficiency improve.

• Journal of Energy Engineering
• /
• v.14 no.4 s.44
• /
• pp.268-276
• /
• 2005

Vacuum Residue (VR) combustion tests were carried out with a 20 kg/hr (fuel feed rate) small scale reactor. The nozzle used was a steam atomized, internal mixing type. Compared to heavy oil, vacuum residue used in this work is extremely high viscous and contains high percentages of sulfur, carbon residue and heavy metals. To ignite atomized VR particles, it was necessary to preheat the reactor, and it has been done with LP gas. The axial and radial gas temperature, major species concentrations and solid sample were analyzed when varying the fuel feed rate. The main reaction zone of atomized VR-air flame in a reactor was anticipated within about 1 m from the burner tip by considering the profiles oi gas temperature, species concentration and particle size measured along with the reactor. At downstream, the thermally, fully developed temperature distribution was obtained. SEM photographs revealed that VR carbon particles collected from the reactor are porous and have many blow-holes on the particle surface.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.96-101
• /
• 2007

Gas Discharge Tubes (GDTs) are widely used as surge protectors for communication applications due to their small internal capacitance. In these days, however, they are mostly used in combined configurations, because the sparkover voltage required to initiate the discharge process in the GDTs and the time taken for arc formation process can be large enough to damage to sensitive circuits. For GDTs with a considerably high initial residual voltage, we should limit the peak voltage using a TVS or filter. We made a hybrid SPD circuits of common-mode type and differential-mode type with the filter using common-mode choke. Also, we applied lightning impulse voltage and ring wave voltage which frequency bandwidth are different each other and verified the characteristics of hybrid SPD circuits according to waveshapes. We describe how the applied SPDs operate in protection process steps with the actual data obtained from the residual voltage measurement at each step. The experiment results show that the surge voltage reduction with the choke coil is more effective in differential-mode circuit than in common-mode circuit.

• Korean Journal of Materials Research
• /
• v.10 no.7
• /
• pp.505-514
• /
• 2000

The carburizing behavior and fatigue properties of the plasma carburized low carbon Cr-Mo steel(0.176C-1.014Cr-0.387Mo) have been investigated. The effective case depth in plasma carburized steel increased up to 50% in comparison with that of gas carburizing, and this case depth increased with the increasing surface carbon content. With increasing time in plasma carburizing, the surface carbon content increased but its increasing rate decreased. Fatigue properties were studied in terms of microstructure, case depth, retained austenite and residual stress near the surface. The fatigue limit of the plasma carburized steel was higher than that of gas carburized one. The initiation of microcracks and initial crack propagation were retarded due to a relatively little surface and internal oxidation layer in plasma carburized steel. Fractography showed the crack initiated at the surface, and transgranular fracture at surface layer was more predominant in plasma carburized steel compared to that of gas carburized steel.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.101-101
• /
• 2016

DLC(Diamond Like Carbon)막은 그 물성의 다양함으로 인하여 산업기계, 금형, 공구, 광학 및 수송기기의 파워셀 부품등 많은 산업분야에 활용되고 있다. 일반적으로 DLC막은 증착에 사용되는 카본의 원료에 따라 크게 두 가지로 나눌 수 있는데, 이는 탄화 수소계 가스(CxHy)를 사용하여 증착된 a-C:H(amorphous Hydro-Carbon)과 고체 카본을 사용하는 a-C(amorphous Carbon)이다. 또한 a-C 중 진공 아크 공법으로 제작된 막(ta-C : tetrahedral amorphous-Carbon)은 다이아몬드 성분인 sp3의 분률이 높아, 그 경도는 40 - 85 GPa 이상이며, 무수소화로 500도 이상의 고온에서도 그 물성의 변화가 적어 그 활용도가 높아지고 있다. 하지만 높은 경도와 더불어 막의 잔류응력이 높아 3 um 이상 후막화하는 것은 어렵다. 이는 높은 잔류응력으로 인한 막의 증착시, 막 자체가 파손되거나, 기판과 막사이의 계면 밀착력이 약하여 박리되거나, 또는 높은 밀착력으로 인하여 모재가 파손되는 등 다양한 문제를 발생한다. 본 연구에서는 이 고경도 무수소 DLC막(ta-C)의 후막화하는 방안으로 주요 코팅 변수와 잔류응력과의 관계를 에너지 관점에서 파악하고 이를 활용 잔류응력을 제어하여 할 수 있는 방법을 제시하고자 한다.

• ETRI Journal
• /
• v.11 no.1
• /
• pp.89-96
• /
• 1989

$C_2F_6$/$CHF_6$ 플라즈마를 이용한 실리콘 산화막의 반응성이온 식각공정시 실리콘 표면에 형성되는 고분자 잔류막과 근표면 손상영역을 X-선 광전자분광법(x-ray photoelectron spectroscopy)과 러더포드 후방산란법(Rutherford backscattering)을 이용하여 연구하였다. 표면 잔류막은 CF, $CF_2$, $CF_3$, $C-CF_x$, 그리고 C-C/C-H 등의 결합을 가진 불화탄소 고분자로 구성되어 있으며, 또한 C 1s와 Si 2p X-선 광선자 스펙트럼으로부터 C-Si 결합이 존재함을 확인하였다. 반응성이온 식각을 거친 실리콘 표면 구조의 연구결과, 불소와 탄소로 구성된 고분자막($<20 \AA$)이 극표면에 존재하며, 식각 후 공기중에 노출됨에 따라 고분자 잔류층으로 산소가 통과하여 기판을 산화시킴으로써 실리콘 산화막( $~10\AA$)이 그 아래에 형성되었음을 알았다. 그리고 실리콘산화막 아래에 탄소-산소 결합영역이 관찰되었다. 플라즈마 가스의 조성에서 $CHF_3$의 량이 증가함에 따라 고분자 잔류막의 두께가 증가하였으며, 본 연구의 실험조건에서 2분간 overetching한 시편의 경우에도 실리콘 표면 영역의 손상정도가 매우 적음을 발견하였다.

• Economic and Environmental Geology
• /
• v.37 no.2
• /
• pp.185-193
• /
• 2004

A physical model experiment was conducted using a sand and gravel-filled tank model, to investigate the influence on the GPR response of LNAPL vapor phase effects in the unsaturated zone and of residual phase of LNAPL trapped in the saturated zone. Background measurements of GPR were made with only water in the tank using a fluctuating water table model. Gasoline was, then, injected into the bottom of the model tank to simulate a subsurface discharge from a leaking pipe or tank at depth, obtaining GPR data with rising and lowering of water table. Results from the experiment show the GPR sensitivity to the changes in the moisture content in the vadose zone and its effectiveness for monitoring minor fluctuation of the water table. The results also demonstrate a potential of GPR for monitoring possible vapor phase effects of volatile hydrocarbons in the vadose zone as a function of time, and for detecting the effects of residual phase of hydrocarbons in the water saturated system. In addition, the results provide the basis for a strategy that has the potential to successfully detect and delineate residual LNAPL contamination in the water-saturated system at field sites where the conditions are similar to those simulated in the physcial models described herein.