• Resources Recycling
• /
• v.26 no.5
• /
• pp.39-47
• /
• 2017

In this study, the precipitation of rare earth-sodium sulfate with sodium sulfate was conducted in order to separate rare earth from Fe in rare earth sulfate solution. Neodymium (Nd) was easily precipitated as Nd-sulfate salt with sodium sulfate, on the other hand, excessive sodium sulfate was needed for the precipitation of Dy-sulfate salt. Also neodymium not only promoted the precipitation of dysprosium sulfate salt but also increased recovery of dysprosium sulfate salt in sulfuric acid solution. At the condition of $60^{\circ}C$ precipitation temperature, 3 h reaction time, 7 equivalents sodium sulfate, the recovery of neodymium and dysprosium sulfate salt was 99.7% and 94.3% respectively from the sulfuric acid solution containing Nd of 23.39 mg/ml and Dy of 8.67 mg/ml. Lastly, from the results of separation of Dy to Nd by the method of sulfate double salt, the effect of salting out with NaCl is important to increase the grade of Dy, and 98.7% of Dy grade could be obtained in this study.

• Resources Recycling
• /
• v.26 no.5
• /
• pp.97-104
• /
• 2017

Nuclear fuel cladding tubes are manufactured through pilgering and the annealing process. In order to remove the oxidized layer and impurities on the surface of the tube, a pickling process is required. Zirconium (Zr) is dissolved in a HF and $HNO_3$ acid mixture during the process and the pickling waste acid, including the dissolved Zr, is completely discarded after neutralization. This study observes the effects of the residual impurities (Ba) in the pickling solution regenerated from the $BaF_2$ precipitation process on the waste pickling solution. In addition, the concentration of Ba and Zr for the actual nuclear fuel cladding tube process was optimized. The regenerated pickling solution was tested through a pilot plant pickling process device that simulates the commercial pickling process of nuclear fuel cladding tubes, and the pickling efficiency was analyzed through AFM analysis of the roughness of the cladding tube surface.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.26-33
• /
• 2017

The behavior on the solvent extraction of heavy rare earths (HRE) by using PC88A was confirmed to demonstrate the possibility of recovery on the HRE from industrial wastewater, which consist of low concentration rare earth. We verified the extraction behavior of the HRE through a change of equilibrium pH, extractant concentration and A/O ratio, and also confirmed the stripping behavior depending on the type of mineral acids. At equilibrium pH 1.0, extraction of rare earth (RE) was completed from 95% to 100%. In all extraction conditions, it tend to be extracted in order of high atomic number. When A/O ratio was 10/1, Yb and Tm were concentrated at the maximum and increased 6-fold and 3-fold compared to initial concentration, respectively. To confirm the stripping behavior of the RE, three mineral acids were applied to the organic phase and consequently rate of stripping was increased in order of $HNO_3$, $H_2SO_4$ and HCl.

• Resources Recycling
• /
• v.29 no.4
• /
• pp.67-72
• /
• 2020

Recycling processes of spent copper wires cosisnt of several steps of cutting and chopping processes for peeling covering materials followed by gravity separation processes, where copper is recovered. Because copper thin wires could be lost during further recycling processes, the wire may need to be further treated. In the present study, the copper thin wire was treated with ball milling to prevent the loss. Since the aggregation of the copper wire could be formed by bending and entangling the copper wire each other, the degree of flexion of the copper wire was measured after ball milling. When the 0.5 cm and 3 cm copper wires were used, the 0.5 cm copper wire was not bent and the 3 cm copper wires were aggregated regardless of the ball addition. When the 1 cm and 2 cm copper wires were used, the degree of flexion was remarkable when the balls were added. In the tests using 2 cm copper wires, the aggregation ratio of the copper wire gradually increased with the amount of the 20 mm alumina ball, and when 200 ml of 30 mm alumina ball was used, the aggregation ratio increased to 89.29 %, but after increasing the ball amount further, the aggregation ratio decreased. Thus, it is expected that the loss of the copper wire could be reducedif when the copper thin wire is treated with ball milling by the aggregation of copper thin wires.

• Resources Recycling
• /
• v.29 no.5
• /
• pp.38-47
• /
• 2020

In this study, factors affecting the adsorption reaction for the separation/recovery of V and W using Lewatit monoplus MP 600, a strong basic anion exchange resin, from the leachate obtained through the soda roasting-water leaching process from the spent SCR DeNO_X catalyst investigated and the adsorption mechanism was discussed based on the results. In the case of the mixed solution of V and W, both ions showed a high adsorption ratio at pH 2-6, but the adsorption of W was greatly reduced at pH 8. In the adsorption isothermal experiment, both V and W were fitted well at the Langmuir adsorption isotherm, and the reaction kinetics were fitted well at pseudo-second-order. As a result of conducting an adsorption experiment by adjusting the pH with H₂SO₄ to remove Si, which inhibits the adsorption of V and W from the leachate, the lowest W adsorption ratio was shown at pH 8.5. Desorption of W was hardly achieved in strongly acidic solutions, and desorption of V was well performed in both strongly acidic and strongly basic solutions.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2019.10a
• /
• pp.82-82
• /
• 2019

황해쑥(Artemisia argyi Lev. et. Vnt)은 국화과의 다년생 초본 식물로서 쑥, 산쑥과 함께 건조한 것이 애엽이라는 생약재로 쓰이며 2016년 기준 전국적으로 81 ha에서 871톤이 생산되고 있다. 주요 유효성분으로 Eupatilin, Jaceosidin 등이 있으며 위궤양에 효과가 있다고 알려져 있어 최근에는 스티렌정 등 신약원료로 각광 받고 있다. 황해쑥은 종자번식 뿐만 아니라 포복경을 이용한 영양번식이 가능하며 현재까지 '섬애' 등 1품종이 개발되어 있으나 농가와 산업체가 요구하고 있는 수량성 또는 Eupatilin 등 성분함량이 높은 품종개발이 필요하다. 국내 연구 결과를 보면 대부분 년 1회 수확을 기준으로 연구되어 왔으나 실제로는 년 2회 수확하는 경우가 더 많다. 따라서 본 실험에서는 년 1회 뿐만 아니라 년 2회로도 수확하여 조사하였다. 시험재료는 AA1801 등 7계통 이며, 시비량은 10 a 당 질소 15.3 kg 인산 20 kg 가리 5 kg이고, 흑색 비닐을 피복한 후 조간 30 cm 주간 15 cm로 하였다. 시험구배치는 난괴법 3반복으로 하였으며 포복경을 5 cm로 잘라 4월 19일에 정식하였다. 1회 수확 시에는 8월 12일, 2회 수확 시에는 6월 17일, 9월 19일에 수확 하였다. 년 1회 수확 시 계통 별 생육특성을 보면, 초장은 202.4~231.5 cm로 평균 213.6 cm 였으며 경경은 10~12.14 mm로 평균 10.9 mm 였다. 분지수는 32.6~37.3개로 평균 35.2개 였으며 엽병장, 엽장, 엽폭은 2.4~4.2 cm, 9.3~12 cm 9.2~12.2 cm로 평균 3.3 cm, 10.7 cm 그리고 10.9 cm 였다. 전초의 생중량과 건중량은 각각 4.9~6.9 kg, 1.8~2.7 kg로 평균 5.5 kg, 2.1 kg 이였다. 특히 AA1902는 다른 계통에 비해 분지수는 적었으나 초장이 크고 경경이 굵었으며 생중량과 건중량도 가장 무거웠다. 년 2회 수확 시 전초의 생중량과 건중량은 각각 5.1~6.2 kg, 1.7~2.0 kg로 평균 5.6 kg, 1.8 kg 이였다. 수량성으로 봤을때는 AA1902는 1회 수확에 적합하며 AA1801, AA1802는 2회 수확 시 생중량과 건중량이 무거웠다. 또한 AA1903의 경우 수확 회수와 상관없이 수량성이 높은 계통으로 판단되었다. 본 자료는 황해쑥 품종육성의 기초자료로 활용하고자 한다.

• Geophysics and Geophysical Exploration
• /
• v.22 no.3
• /
• pp.149-159
• /
• 2019

Borehole elemental concentration logging, measuring neutron-induced gamma rays by inelastic scattering and neutron capture interactions between neutron and formation, delivers concentrations of the most common elements found in the minerals and fluids of subsurface formation. X-ray diffraction and X-ray fluorescence analysis from core samples are traditionally used to understand formation composition and mineralogy, but it represents only part of formations. Additionally, it is difficult to obtain elemental analysis over the whole intervals because of poor core recovery zones such as fractures or sand layers mainly responsible for groundwater flow. The development of borehole technique for in situ elemental analysis plays a key role in assessing subsurface environment. Although this technology has advanced consistently starting from conventional and unconventional resources evaluation, it has been considered as exclusive techniques of some major service company. As regards domestic research and development, it has still remained an unexplored field because of some barriers such as the deficiency of detailed information on tools and calibration facility for chemistry and mineralogy database. This article reviews the basic theory of spectroscopy measurements, system configuration, calibration facility, and current status. In addition, this article introduces the domestic researches and self-development status on borehole elemental concentration tools.

• Resources Recycling
• /
• v.29 no.6
• /
• pp.65-72
• /
• 2020

Black dross is a dark gray dross generated during the aluminum recycling process that uses flux, and contains NaCl, KCl, Al2O3, MgO, etc. Black dross is separated into soluble substances (NaCl, KCl) and insoluble substances (Al2O4, MgO) through the dissolution process. Soluble materials can be reused as salt flux, and Al2O3 and MgO can be upcycled to various ceramic materials through the synthesis process. In this study, Mayenite was synthesized using Al2O3 and MgO recovered from black dross, and the synthesis was performed according to the mixing ratio and reaction temperature. It was confirmed that when Mayenite was synthesized using black dross (spinel) and CaCO3, precursors were changed to Mg0.4Al2.4O4 and CaO at 700 ℃, and to Ca12Al14O33 (Mayenite) after 800 ℃. In the mixing conditions experiment, it was confirmed that the Mayenite XRD peak increased with increase of the CaCO3 content, and the Mg0.4Al2.4O4 XRD peak decreased. As a result of the BET analysis of the synthesized powder, the surface area decreased as the fine particles were grown and agglomerated in the process of generating mayenite.

• Resources Recycling
• /
• v.29 no.6
• /
• pp.27-34
• /
• 2020

In order to remove sulfate(SO42-) and purify the Li2CO3, dissolution and recrystallization of crude Li2CO3 using distilled water and HCl solution was performed. When Li2CO3 was dissolved using distilled water, the amount of dissolved Li2CO3(wt.%) increased as the solution temperature decrease and showed about 1.50 wt.% at 2.5℃. In addition, when Na2CO3 was added and the Li2CO3 solution was recrystallized, the recrystallization(%) increased with increasing temperature, resulting in a 49.00 % at 95 ℃. On the other hand, when Li2CO3 was dissolved using HCl solution, there was no effect of reaction temperature. As the concentration of HCl solution increased, the amount of dissolved Li2CO3(wt.%) increased, indicating 7.10 wt.% in 2.0 M HCl solution. When the LiCl solution was recrystallized by adding Na2CO3, it exhibited a recrystallization(%) of 86.10 % at a reaction temperature of 70 ℃, and showed a sulfate ion removal(%) of 96.50 % or more. Finally, more than 99.10 % of Na and more than 99.90 % of sulfate were removed from the recrystallized Li2CO3 powder through water washing, and purified Li2CO3 with a purity of 99.10 % could be recovered.

• Resources Recycling
• /
• v.31 no.1
• /
• pp.56-64
• /
• 2022

Construction waste is generated at a rate of approximately 221,102 tons/day in Korea. In particular, mixed construction waste generates approximately 24,582 tons/day. The other components were recycled by 98.9%. The amount of greenhouse gas emissions from the waste was 17.1 million tons of CO2 equaling 2.3% of the total greenhouse gas emissions. To reduce greenhouse gas emissions, reducing the environmental impact is becoming increasingly important. However, appropriate treatment must first be established, as mixed construction waste is also increasing. Thus, an effective plan is urgently needed because it is frequently segregated and sorted by the landfill and incinerated. In addition, there is an urgent need to prepare various effective recycling methods rather than a simple treatment. Therefore, this study analyzed the environmental impact of the treatment of mixed construction waste by calculating greenhouse gas emissions. As a result, the highest greenhouse gas generation occurred during the incineration stage. Moreover, the optimal method to reduce greenhouse gas emissions is recycling and energy recovery from waste. In addition, the amount of greenhouse gas generated during energy recovery from the waste stage was the second highest. However, greenhouse gas emissions can be reduced by using waste as energy to reduce fossil fuel consumption. In addition, for the transportation stage, the optimal reduction plan is to minimize the amount of greenhouse gas emissions by setting the optimal distance and applying biofuel and electric vehicle operations.