• Journal of the Korean Magnetics Society
• /
• v.4 no.3
• /
• pp.233-238
• /
• 1994

The effect of die upset and heat treatment on the magnetic properties of mechanically ground $Nd_{16}Fe_{78}B_{6}$ alloys has been studied. Although stripe domain patterns parallel to the compression direction were observed after die upset, it was found that crystallographic c-axes of a specimen were not completely aligned along the compression direction' which resulted in the decrease of Br. The average grain size of a die-upset specimen annealed for 5 hours at $1000^{\circ}C$ was about $20\mu\textrm{m}$, resulting in reduced values of Br and $_{i}H_{c}$. The maximum magnetic properties (Br=7.8 kG and $(_{i}H_{c}=14\;kOe) were obtained from the magnet die-upset at $750^{\circ}C$ using the alloy powder ground for 13 hours.

• Korean Journal of Crystallography
• /
• v.12 no.3
• /
• pp.182-187
• /
• 2001

The purpose of this study is to investigate the degradation of soft magnetic properties of Fe-Hf-N thin films after annealing in vacuum. They were annealed at 450℃∼650℃. The microstructure and crystal phase of the selected area of the thin films were analyzed by TEM and SAD. After annealing at 450℃-600℃, the coercivity of the films increased by 0.2 Oe and the effective permeability decreased by 1500 as compared with them before annealing due to the growth of α-Fe crystallites. The saturation magnetic flux density of the films increased by 0.5 KG after annealing under 600℃. However, the soft magnetic properties of the film annealed at 650℃ degraded abruptly, which was attributed to the destruction of nano-crystalline microstructure of the film due to the rapid growth of α-Fe crystallites with the segregation of N sited in the α-Fe lattice into HfN.

• Journal of the Korean Magnetics Society
• /
• v.12 no.2
• /
• pp.57-63
• /
• 2002

In order to increase the magnetic properties of a Nd-Fe-B sintered magnet, the general factors including particle size and its distribution, volume fraction of Nd$_2$Fe$_{14}$B phase, degree of alignment of Nd$_2$Fe$_{14}$B grain, oxygen content and grain size etc. should be optimized by controlling the composition of Nd-Fe-B alloy as well as the manufacturing process. In this study, fabrication of the Nd-Fe-B sintered magnet was carried out in a laboratory scale by controlling the composition of Nd-Fe-B alloy and the manufacturing process. The optimum milling condition was found by investigating the milling media, milling time and ball size. The addition of FeGa was effective to increase the coercivity of the Nd-Fe-B sintered magnet. A remanence of 14.4 kG, a coercivity of 9.4 kOe and a maximum energy product of 47 MGOe were obtained from the sintered magnet.

• Journal of the Korean Magnetics Society
• /
• v.5 no.1
• /
• pp.34-37
• /
• 1995

$Nd_{x}Fe_{77}B_{23-x}(x=4,\;6,\;8,\;11,\;13)$ alloys were prepared by rapid quenching technique. They were crystallized at higher than $650^{\circ}C$ and subsequently the magnetic properties were investigated The melt-spun alloy of x=8 consisted of nearly single metastable compound $Nd_{2}Fe_{23}B_{3}$ and showed the soft magnetic property. In $8{\leq}x{\leq}13$ alloys, the coercivities were increased according to the increase of Nd content but the remanences decreased. In $4{\leq}x{\leq}6$ alloys, the coercivities and the remanences were increased by lowering Nd content. In x=4 alloy, the ratio of soft to hard magnetic phase was 70:30 and the energy product was $96kJ/m^{3}(12MG.Oe)$.

• Journal of the Korean Magnetics Society
• /
• v.2 no.1
• /
• pp.44-49
• /
• 1992

Magnetic properties and microstructures of $Nd_{12}Fe_{80}B_{6}(Nb,\;M)$ (M=Ti/Cu/Ga) melt-spun ribbons prepared by single wheel technique have been studied. The results of microstructural study have shown that Ga is effective for the orientation of c-axis normal to the ribbon plane. The Ga-added melt-spun ribbon, $Nd_{12}Fe_{80}B_{6}(Nb,\;Ga)$, quenched at $V_{s}=17.9\;m/s$ was mostly composed of fine grains of about 30 nm in size with the textured free-side surface. The powder of this ribbon aligned in mag-netic field showd a high remanence of 0.87 T which was about 5 % higher than that of ribbon itself. It is believed that there is a possibility to fabricate a new type of HIREM melt-spun ribbon with highly textured free-side surface.

• Journal of the Korean Magnetics Society
• /
• v.6 no.2
• /
• pp.80-85
• /
• 1996

An externally applied magnetic field during annealing the $Nd_{2}Fe_{14}B/Fe_{3}B$ based spring magnet was found to enhance the exchange coupling between the hard and soft magnetic grains. More than 30 % increase in remanence values for melt-spun $Nd_{4}Fe_{73.5}Co_{3}(Hf_{1-x}-Ga_{x})B_{18.5}$(x=0, 0.5, 1.0) alloys was resulted from uniform distribution of $Fe_{3}B$, $\alpha$-Fe as well as $(Nd_{2}Fe_{14}B)$, and also from reduced grain size of those phases by 20 %. The result also showed that there is an optimum grain size exhibiting a high coercivity value which will be discussed in terms of previously simulated exchange coupling parameter.

• Journal of Advanced Navigation Technology
• /
• v.17 no.3
• /
• pp.332-345
• /
• 2013

In this paper, recently, it is described to the piezoelectric transformer technology develops, because it was have to favorable characteristics such as electromagnetic-noise free, compact size, higher efficiency, and superior power density, flux linkage, noiseless, etc. its resonance frequency was used to output waveform of a sine wave. A rotor speed identification method of induction motor based on the theory of flux model reference adaptive system(FMRAS). The estimator execute the rotor speed identification so that the vector control of the induction motor may be achieved. The improved auxiliary variable of the model are introduced to perform accurate rotor speed estimation. The control system is composed of the PI controller for speed control and the current controller using space voltage vector PWM techniuqe and DC-DC converter. High speed calculation and processing for vector control is carried out by digital signal one chip microprocessor. Validity of the proposed control method is verified through simulation and experimental results.

• Journal of Applied Biological Chemistry
• /
• v.64 no.4
• /
• pp.351-356
• /
• 2021

Changing environmental conditions can affect plant growth by influencing water and nutrient transport and photosynthesis. Plant physiological responses under changing environmental conditions can be non-destructively monitored using electrodes as plant induced electrical signal (PIES). Objective of the study was to monitor PIES in response to increased CO₂ and decreased photosynthetic photon flux density (PPFD). The PIES increased during day time when transpiration and photosynthesis occurs and monitored CO₂ concentration was negatively correlated to the PIES. Enhanced CO₂ concentration slightly reduced PIES, but the effect of increased CO₂ was limited by light intensity. The effect of reduced PPFD was not appeared immediately because water and nutrient transport was not promptly affected by the light. The study was conducted to evaluate short-term effect of increasing CO₂ and decreasing PPFD, hence proline content and chlorophyll fluorescence was not significantly affected by the conditions.

• Journal of Bio-Environment Control
• /
• v.18 no.1
• /
• pp.23-28
• /
• 2009

This study was conducted to evaluate the effect of optimized environment conditions with growth stage in photoautotrophic micropropagation on the growth of potato (Solanum tuberosum L. cv. Dejima) plantlets and energy efficiency. Optimum environment conditions at each stage were decided in our previous study. For the evaluation of optimized environment control, potato plantlets were cultured under four different conditions: photoautotrophic optimum conditions of photosynthetic photon flux density (PPFD) and $CO_2$ levels with growth stage (POG), photoautotrophic constant condition with average PPFD and $CO_2$ levels (PCA), photoauototrophic constant condition with maximum PPFD and $CO_2$ levels (PCM), and photomixotrophic conventional condition with 3% sucrose (PMC) as control. As a result, environment control with growth stage (POG) significantly promoted all the growth characteristics such as the number of nodes and unfolded leaves, shoot height, shoot diameter, and fresh and dry weights of potato grown in vitro. In addition, based on dry weight consumed electricity and $CO_2$ were the lowest in POG suggesting the highest energy efficiency among the treatments. After transferring potato plantlets to greenhouse, the plantlets under POG showed vigorous growth, which was pretty similar with those under PMC. The accumulations of dry matter in POG were 4.7 times in vitro and 3.8 times in greenhouse as much as those in the conventional control (PCM). Thus, we concluded that in vitro environment control with growth stage induced vigorous growth of potato plantlets both in vitro and in greenhouse with less energy consumption.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.8 no.4
• /
• pp.46-54
• /
• 1994

Exhbitlon hghting design be done aftrr due consideration of the photochermcal reaction and h ~ ~ i i tc~.fficits~ upn exposure to light. In this study the balanced judgement is as follows. The most light-susceptible material shouid be illu~stratrui less than 50[k] (illurnlnance-hours per year : 120, 000k.h)and the illuminance of moderately sensitive rriatcrinl k 200[1x] (illuminance hours per year : 480, 0001x.h). Moreover to minimize damage the sources of light shoulcl not only contribute as little as heat possible but remove ultraviolt radiation by filters. Also the sources of light must have good color rendering and low color temperature.