• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1206-1209
• /
• 2018

Single-layer winding configuration in a 12-slot 10-pole Permanent Magnet Synchronous Motor (PMSM) has been adopting in electrical power steering (EPS) systems to get the high fault tolerance capability of the motor. However, the motor with single-layer winding has magnetic circuit saturations in the teeth, which deteriorates its performance. In this paper, we propose asymmetric teeth widths to get over the demerit, and analyze the effect of the teeth width ratio variations on the performances of the PMSM. As a result, we suggest the most valuable teeth width ratio for designing the PMSM with a single-layer winding configuration.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.42-47
• /
• 2008

In this paper, the fault current limiting characteristics for the superconducting fault current limiter(SFCL) using magnetic coupling between two coils were investigated. The SFCL consists of a high-$T_c$ superconducting(HTSC) element and two coils. This SFCL has different characteristics that depend on the connection form, the winding direction and the inductance ratio of two coils. The impedance and the operational current of the SFCL can be adjusted higher or lower than the resistance and the critical current of HTSC element. Therefore, the SFCL can change the amplitude of the limited fault current. To confirm it, the HTSC element was modeled and the fault current limiting characteristics of the SFCL were analysed through computer simulation. It was obtained from the analysis that the connection form and the winding direction of two coils of the SFCL were the important design parameters.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.223-224
• /
• 2004

고준위폐기물 혹은 사용후 핵연료의 처분용기 재질은 각 국의 처분개념과 처분공의 주위 환경에 따라 달라질 수 있다. 용기의 후보재질로는 탄소강, 스텐레스 강, 구리, 니켈, 티탄 혹은 이들의 합금이 주로 고려되고 있으나, 국내에서는 아직 선정되지 않았다. 국내 처분환경에서 이들 재질의 부식특성을 조사하고자 모의 화강암 지하수를 가해 만든 겔 상태의 경주 벤토나이트에 탄소강, 스텐레스 강, 구리 시편을 넣고, $70^{\circ}C$, 아르곤 분위기에서 530일 경과한 후 시편의 표면 변화 (그림 1) 및 무게 감소를 측정하였다. 철 부식시편은 검정색의 철 화합물 층으로 덮여 있었으며, 구리표면에는 노란색의 부식층이 형성되었는데, 이를 XRD로 분석한 결과 $Cu_2O$로 판명되었다. 그러나 $700^{\circ}C$에서 각각 0, 24, 96시간동안 예민화시킨 스텐레스 강 시편들은 모두 초기상태 그대로 광택을 유지하고 있었으며, XRD에서 다른 화합물의 형성을 발견할 수 없었다 (그림 2). 시편의 무게 감소가 균일부식에 기인한 것으로 가정하여 환산한 결과, 구리와 스텐레스 강 모두 0.3~0.4 $\mu\textrm{m}/yr$의 부식속도를 나타내었다. 그러나 구리는 부식생성물이 표면에 부착되어 있기 때문에 실제 부식두께는 이 값보다 더 클 것으로 생각된다. 용기가 초기 530일간과 같은 속도로 처분용기의 부식이 진행된다면 한국에서 기준처분 개념으로 삼고 있는 50mm 두께의 내부식성 외벽 금속용기는 적어도 만년이상 견딜 수 있을 것으로 추정된다. 한편, 검정색 부식층을 제거한 무게감소로부터 계산한 철의 부식속도는 구리의 약 30배에 해당하였다. 금속 재질의 정확한 부식 거동을 파악하기 위해서는 보다 장기간의 실험이 요구된다. 시험법 선정에 각계(규제기관, 학계, 발전소 현장 및 산업계 등) 전문가로부터 기술자문회의를 통하여 자문 의견을 받기로 하였다. 특히 현재 폐기물 인수 기술기준치가 설정된 국가의 시험법을 심층 있게 검토하기로 하였다.검토하기로 하였다. 혹은 수성주변 환경이 지배하는 산악이나 구릉지에서 흔히 나타나는 침엽수-낙엽활엽수의 혼합림 식생상태를 잘 대변해 주고 있는 것으로 판단된다. 끝으로, 의림지 호저 퇴적층 중에서 인위적인 교란흔적이 없는 암회색 유기질 니층에 대한 탄소연대측정 결과, 제1호공 12번 시료에서 950$\pm$40 years B.P을 얻었으며, 제3-1호공에서도 아래로 내려가면서 8, 10, 11번 시료에 대하여 500$\pm$30 years B.P, 650$\pm$30 years B.P, 800$\pm$40 years B.P의 연대측정 결과를 획득하였다. 이상과 같은 의림지 호저 퇴적층의 형성환경과 형성시기 연구를 통하여 의림지의 제방축조의 최초시기를 해석해 보면, 의림지의 제방은 적어도 과거 약 827년 전에서 866년 전에는 이미 축조되어 있었음을 알 수 있다. 과거 제천 일대에 살았던 옛사람들이 의림지 하류의 곡지중앙과 고기 충적선상지에 대한 관계용 용수조달의 필요성에 부응하여 상류부 곡지하천의 자연입지 환경을 최대한 이용하여 축조한 것으로 판단된다..준비하였다.전류를 구성하는 주요 입자의 에너지 영역(75~l13keV)에서 가장 높은(0.80) 상관계수를 기록했다. 넷째, 회복기 중에 일어나는 입자들의 유입은 자기폭풍의 지속시간을 연장시키는 경향을 보이며 큰 자기폭풍일수록 현저했다. 주상에서 관측된 이러한 특성은 서브스톰 확장기 활동이 자기폭풍의 발달과 밀접한 관계가 있음을 시사한다.se that were all low

• Geophysics and Geophysical Exploration
• /
• v.10 no.1
• /
• pp.89-97
• /
• 2007

A three-dimensional (3D) magnetotelluric (MT) survey has been carried out to delineate subsurface structures and possible fractures, for development of low-temperature geothermal resources in Pohang, Korea. Quite good quality MT data could be obtained throughout the survey region by locating the remote reference in Kyushu, Japan, which is ${\sim}480\;km$ from the centre of the field site. 3D modelling and inversion are performed taking into account the sea effect in MT measurements near the seashore. The nearby sea in the Pohang area affects MT data at frequencies below $1\;Hz{\sim}0.2\;Hz$, depending on the distance from the seashore. The most severe sea effects were observed in the south-east parts of the survey area, closer to Youngil Bay. 3D inversion with and without the seawater constraint showed very similar results at shallow depths, roughly down to 2 km. At greater depths, however, a strong sea effect seems to form a fictitious conductive structure in ordinary 3D inversion, especially in the south-eastern part of the survey region. Comparison between drilling results and the resistivity profiles from inversions showed that five layered structures can be distinguished the subsurface beneath the target area. They are: (a) semi-consolidated mudstones with resistivity less than $10\;{\Omega}m$, which are ${\sim}300\;m$ thick in the northern part and ${\sim}600\;m$ thick in the southern part of the survey area; (b) occasional occurrence of trachybasalt and lapilli tuff within the mudstone layer has resistivity of a few tens of${\Omega}m$, (c) intrusive rhyolite ${\sim}400\;m$ thick has resistivity of several hundreds of ${\Omega}m$, (d) alternating sandstone and mudstone down to 1.5 km depth shows resistivity of ${\sim}100\;{\Omega}m$, (e) a conductive structure was found at a depth of ${\sim}3\;km$, but more geological and geophysical study should be carried out to identify this structure.

• Journal of the Korean earth science society
• /
• v.29 no.1
• /
• pp.1-12
• /
• 2008

A geophysical mapping was performed for Hwasan caldera which is located in Euisung Sub-basin of the southeastern part of the Korean Peninsula. In order to overcome the limitation of the previous studies, remote sensing technic was used and dense potential data were obtained and analyzed. First, we analyzed geological lineament for target area using geological map, digital elevation model (DEM) data and satellite imagery. The results were greatly consistent with the previous studies, and showed that N-S and NW-SE direction are the most dominant one in target area. Second, based on the lineament analysis, highly dense gravity data were acquired in Euisung Sub-basin and an integrated interpretation considering air-born magnetic data was made to investigate the regional structure of the target area. The results of power spectrum analysis for the acquired potential data revealed that the subsurface of Euisung Sub-basin have two density discontinuities at about 1 km and 3-5 km depth. A 1 km depth discontinuity is thought as the depth of pyroclastic sedimentary rocks or igneous rocks which were intruded at the ring vent of Hwasan caldera, while a 3-5 km depth discontinuity seems to be associated with the depth of the basin basement. In addition, three-dimensional gravity inversion for the total area of Euisung Sub-basin was carried out, and the inversion results indicated two followings; 1) Cretaceous Palgongsan granite and Bulguksa intrusion rocks, which are located in southeastern part and northeastern part of Euisung Sub-basin, show two major low density anomalies, 2) pyroclastic rocks around Hwasan caldera also have lower density when compared with those of neighborhood regions and are extended to 1.5 km depth. However, a poor vertical resolution of potential survey makes it difficult to accurately delineate the detailed structure caldera which has a vertically developed characteristic in general. To overcome this limitation, integrated analysis was carried out using the magnetotelluric data on the corresponding area with potential data and we could obtain more reasonable geologic structure.

• Geophysics and Geophysical Exploration
• /
• v.8 no.2
• /
• pp.145-155
• /
• 2005

A two-dimensional (2-D) interpretation of MT data has been performed for the purpose of fracture detection for geothermal development. Remote stations have been operated in Kyushu, Japan (480 km apart) as well as in Korea (60 km and 165 km apart in 2002 and 2003 data set, respectively). Apparent resistivity and phase curves calculated by remote processing with the Japan remote data showed enough quality for 2-D inversion for the whole frequency range. Remote reference processing with Korea remote reference data also showed quite good continuity in apparent resistivity and phase curves except some noisy frequency bands; around the power frequency, 60 Hz, and around the dead band $10^{-1}Hz\;Hz\;\~1\;Hz$, where the natural EM signal is known to be very weak. Even though the subsurface showed severe three-dimensional (3-D) characteristics in the survey area so that 2-D inversion by itself could not give enough information for deep geological structures, the 2-D inversion for the 5 survey lines showed several common features. The conductive semi-consolidate mudstone layer is dipping from north to south (about 500 m depth on the south and 200 m on the north most part of the survey area). The boundary between the low (L-2) and high (H-2) resistivity anomalies can be thought as a major fault with strike $N15^{\circ}E$, passing through the sites 206, 112 and 414. The shallow (< 1 km) conductive anomalies (L-4) seem to be fracture zones having strike E-W (at site 105) and $N60^{\circ}W$ (at site 434). And there exists a conductive layer in the western and west-southern part of the survey area in the depth below $2\~3\;km$, for which further investigation is to be needed.

• Geophysics and Geophysical Exploration
• /
• v.10 no.4
• /
• pp.268-274
• /
• 2007

Traditional two-dimensional (2D) interpretation of magnetotelluric (MT) data utilizes only transverse magnetic (TM)-mode data, because 2D inversion of transverse electric (TE)-mode data results in spurious features when 3D structures exist in the subsurface. The application of a 3D inversion algorithm to a single MT profile can reduce contamination due to off-profile anomalies and help us to incorporate TE-mode data in the interpretation. In this study, we conduct 2D and 3D inversions of MT data observed along two lines in Jeju Island. First, we invert apparent resistivities and phases in the TM and TE modes separately. Then, we perform 2D joint inversion of both TM- and TE-mode data and 3D inversion of both Zxy- and Zyx-mode data corresponding to TE- and TM-mode data in 2D. The resistivity images derived from all four data show that the geoelectrical structure in Jeju Island is a three-layered earth with the resistive-conductive-resistive stratigraphy within a depth of 5 km. The 3D inversion does not produce clear anomalies in the reconstructed profile image, while all of 2D do. This attributed to the possibility that 2D inversion results are distorted by exiting off-profile 3D anomalies in Jeju. With 3D inversion of 2D profile MT data, we can deduce more reliable results that are not seriously distorted by off-profile 3D anomalies.

• Journal of the Korean earth science society
• /
• v.30 no.7
• /
• pp.834-844
• /
• 2009

Two-dimensional magnetotelluric (MT) inversion algorithm using minimum support (MS) stabilizer functional was implemented in this study to enhance the contrast of inverted images. For this implementation, this study derived a formula in discrete form for creeping model updates in the least-squares linearized inversion. A spatially varying regularization parameter determination algorithm, which is known as ACB (Active Constraint Balancing), was also adopted to stabilize the inversion process when using MS stabilizer as a model constraint. Inversion experiments for a simple isolated body model show well the feature of MS stabilizer in concentrating the anomalous body compared with the second-order derivative model constraint. This study also compared MS stabilizer and the second-order derivative model constraints for a model having multiple anomalous bodies to show the applicability of the algorithm into field data.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.433-441
• /
• 1999

This paper presents a S-FES(Superconducting magnetic becuing Flywheel Energy Storage System) for the p purpose of replacing battery used to store the energy. Especially, the design elements of FES, such as the b beming, wheel mateηaI, and power converter, etc., are described. The design and manufacturing techniques of t the controllable IXlwer converter are proposed to generate the sinusoidal output current in the high speed operation and to get the const빠synchronous motor with halbach cuTay of high coesive I\d-Fe-B permanent magnet is used as the driver of F FES. The proposed S-FES system shows the stable rotation characteristics at high speed range about l 10,000[rpm]. To verify the validity of proposed system, the comparative study with the conventional ball b beming s~rstem is proceeded and it is well confirmed with the result of the lower friction losses of S-FES S system.

• Proceedings of the Korean Quaternary Association Conference
• /
• 2004.06a
• /
• pp.46-46
• /
• 2004

Van Mijenfjorden은 스발바드 군도의 Spitsbergen 서부에 위치하는 두 번째로 큰 피오르드로 온난하고 염분도가 높은 북대서양의 표층수가 북극해로 유입되는 Gateway에 위치하기 때문에 전지구적이며 지역적인 기후변화의 영향을 받는 지역이다. 1999년 IMAGES 프로그램의 일환으로 프랑스 탐사선인 'R/V Marion Dufresne'을 이용하여 북극해의 스발바드 군도에 위치하는 Van Mijenfjorden (77$^{\circ}$ 46.87'N and 15$^{\circ}$ 17.81'E)에서 약 18m의 빙ㆍ해양 퇴적물 코아(MD99-2305)를 시추하여 마지막 최대 빙하기 이후의 고환경변화를 연구하였다. AMS 14C 연대 측정에 의하면 diamicton 층인 하부 2m를 제외한 16m의 퇴적층은 지난 12cal. ka BP경에 피오르드에 존재하던 조수빙하(tidewater glacier)가 해빙되기 시작한 이후에 퇴적되었다. 특히 유기지화학 자료와 부유성과 저서성 유공충의 산출양상 그리고 저서성 유공충인 C. reniforme의 산소ㆍ탄소 안정동위원소 비에 의하면 코아 MD99-2305에는 Van Mijenfjorden에서 홀로세 동안에 일어난 퇴적환경변화를 잘 기록하고 있다. 특히 홀로세 동안에 피오르드내의 퇴적환경 변화는 조수빙하의 확장과 후퇴와 밀접한 관계가 있으며, 유기물의 탄소동위원소(13Corg) 비는 -24에서 -22$\textperthousand$ 값의 변화를 보인다. 이는 Van Mijenfjorden 퇴적물에 공급된 유기물은 육상과 해양기원이 혼합되어 퇴적되었음을 지시한다. 지난 12 cal. ka BP 이후 13Corg 값이 뚜렷하게 변하는 것은 Van Mijenfiorden에서 조수빙하의 변동과 표층수에서의 생산력의 변화를 강하게 반영한다. 강하게 반영한다.53%가 이공계 출신, 100대 기업 CEO의 38.4%가 이공계 출신, 대입수능시험에서 자연계 지원비율이 감소 -40.1%('99)\$\longrightarrow$34.7%('00)\$\longrightarrow$29.4%('01)\$\longrightarrow$26.9%('02)\$\longrightarrow$30.3%('03)\$\longrightarrow$31.5%\$\longrightarrow$'04)필요성, 효과적인 운전자 교육 정책 등이 그것이다. 자동차 긴급 피난 차선은 유용한 시설로 여러곳에서 그 기능이 발휘되고 있으므로 많은 고속도로 관계자들은 설계, 시공 및 유지 관리 측면에서 유의해야 할 것이다.미세조직을 광학현미경으로 압출방향에 평행한 방향과 수직방향으로 관찰하였고, 열간 압출재 이방성을 검토하기 위하여 X선 회절분석을 실실하여 결정방위를 확인하였다. 전기 비저항 및 Seebeck 계수 측정을 위하여 각각 2$\times$2$\times$10$mm^3$ 그리고 5$\times$5$\times$10TEX>$mm^3$ 크기의 시편을 준비하였다.준비하였다.전류를 구성하는 주요 입자의 에너지 영역(75~l13keV)에서 가장 높은(0.80) 상관계수를 기록했다. 넷째, 회복기 중에 일어나는 입자들의 유입은 자기폭풍의 지속시간을 연장시키는 경향을 보이며 큰 자기폭풍일수록 현저했다. 주상에서 관측된 이러한 특성은 서브스톰 확장기 활동이 자기폭풍의 발달과 밀접한 관계가 있음을 시사한다.se that were all low in two aspects, named "the Nonsignificant group". And the issues were