• Composites Research
• /
• 제36권4호
• /
• pp.270-274
• /
• 2023

필라멘트 와인딩 공정을 사용한 FRP 복합재의 적층 구조는 기존의 FRP 복합재의 적층 구조와는 다를 뿐만 아니라 일반적인 적층 구조를 토대로 기계적 물성에 대해서 분석하고자 한다면 그에 대한 영향을 파악하는 것이 어렵다. 따라서 전반적인 성능을 향상시키기 위해 기계적 물성을 개선하고 교차 적층 구조를 최적화하는 것이 필수적이다. 따라서 본 연구는 비정질 할로이사이트 나노튜브(Amorphous Halloysite Nanotubes, A-HNT)를 5개의 층 배열을 통해 교차 적층 탄소 섬유 강화 플라스틱(CFRP) 구조의 저속 충격 특성에 미치는 영향을 조사하는 것을 목표로 한다. 중량 낙하식 충격시험을 통하여 라미네이트의 저속 충격 특성을 확인하였으며, 충격을 가한 후에 현미경을 통하여 충격 파손 모드와 손상 정도를 비교 평가하였다. 나노 입자의 첨가 여부에 따른 각각의 교차 적층 구조 라미네이트를 10 J과 15 J의 충격에너지에서 비교하였다. 10 J의 경우 흡수에너지는 각 구조에서 비슷한 경향을 보였다. 그에 비해 15 J의 경우 흡수에너지는 각 구조에서 다른 흡수에너지를 가지며, 나노 입자가 첨가되지 않은 구조가 가장 높은 흡수에너지를 가진다. 또한 광학현미경을 통하여 각 구조에서 다양한 충격 파손 모드가 관찰되었다.

• 한국해양공학회지
• /
• 제23권6호
• /
• pp.93-98
• /
• 2009

The mechanical properties of $MoSi_2$ based composites containing various types of reinforcement, such as SiC, $ZrO_2$, and W, were investigated, based on detailed examinations of their microstructures. $MoSi_2$ based composites were fabricated at a temperature of $1350^{\circ}C$ using a hot-press device. The volume fraction of SiC and $ZrO_2$ particles in this composite system was fixed as 20%. The volume fraction of three types of W particles was changed from 10% to 30%. The characteristics of the $MoSi_2$ based composites were determined by means of optical microscopy and a three-point bending test. The addition of W particles to the $MoSi_2$ powders exhibited a sufficient improvement in the microstructure and mechanical property of the sintered $MoSi_2$ materials, compared to those of SiC and $ZrO_2$ particles. In particular, W/$MoSi_2$ composites containing W particles of 20 vol% represented a good flexural strength of about 530MPa at room temperature, accompanying a relative density of about 92%. The flexural strength of the W/$MoSi_2$ composites tended to decrease with an increase in the average size of the W particles.

• 한국안전학회지
• /
• 제32권3호
• /
• pp.1-7
• /
• 2017

Particle reinforced composites are materials that have enhanced physical properties by adding particle reinforcements to polymer materials and have been applied to a wide range of fields such as the aerospace, bio-technology and automative industry. In this study, particle reinforced composites were prepared by mixing $SiC/Al_2O_3$ to the vinyl ester as the thermoset resin. The purpose of this study is to evaluate mechanical properties and fracture behavior by the tensile test and single edge notch specimen according to the addition ratio of reinforcement. Addition of 1 and 2 wt% of the particle reinforcement to the vinyl-ester resin was effective for the strength improvement. However, when it was more than 3 wt%, its strength was decreased. Also the highest elastic modulus obtained as 3.19 GPa was found at the 2 wt% addition of reinforcement. Futhermore the fracture toughness was evaluated by the energy release rate and the maximum critical energy release rate was obtained when 1 wt% reinforcement. The results show that the limit of adding of $SiC/Al_2O_3$ for improvement of the mechanical and fracture performance is 2 wt% reinforcement particles.

• 한국주조공학회지
• /
• 제21권1호
• /
• pp.7-14
• /
• 2001

The research on new DRA(discontinuous reinforced alloy) and CRA(continous reinforced alloy) composites has been carried out to improve the properties of ceramic fiber and particle reinforced metal matrix composites(MMCs). Effects of alloying elements and aging conditions on the microstructures and aging behavior of Al-Si-Cu-Mg-(Ni)-SiCp composite have been examined. The specimens used in this study were manufactured by duplex process. The first squeeze casting is the process to make precomposite and the second squeeze casting is the process to make final composite. The hardening behavior was accelerated with decreasing the size of SiCp particle in the composites. It is considered that the dislocation density increased with increasing SiCp size, due to the different thermal deformation between Al matrix and SiCp during quenching after the solution treatment. Peak aging time to obtain the maximum hardness in 3 ${\mu}m$ SiCp reinforced Al composite was reduced than that in large size(5, 10 ${\mu}m$) of SiCp because of difference in dislocation density. Aging hardening responce(${\Delta}H$ = $H_{Max}.-H_{S.T}$) of composites was greater than that of unreinforced Al alloy because of higher density of second phases in matrix.

• 한국주조공학회지
• /
• 제20권6호
• /
• pp.377-385
• /
• 2000

Al matrix composites as the most promising MMCs can be expected to be excellent engineering materials in the nearest future. So as to improve material properties of composite, many manufacturing processes have been developed. Among them, squeeze casting process which offers fine microstructure and near-net-shape is one of the most successful MMCs manufacturing processes. But, in case of with subsieve size particles (under 44 ${\mu}m$), it is very difficult to homogeneously distribute particles in matrix of Al matrix composite by various casting processes, including squeeze casting used so far. Duplex process which was developed in previous study was used to distribute the particle of subsieve size more homogeneously in matrix of Al matrix composite. Microstructures, wear and heat resistance characterization of Al-Si-Cu-Mg-(Ni)/SiCp manufactured by duplex process were examined to clarify the effect of manufacturing conditions, particle size of reinforcement and alloying elements. Al matrix composites reinforced with SiCp(10 ${\mu}m$) have the lowest wear amount among composites reinforced with 3 ${\mu}m$, 5 ${\mu}m$ and 10 ${\mu}m$ SiCp. The wear amount of Al matrix composites with 10 wt.% SiCp(3, 5, 10 ${\mu}m$) was decreased according to the increase of the sliding speed because abrasive wear takes place at high sliding speed of 4m/s and worn debris with block type occurs at low sliding speed of 1m/s. As for heat resistance, it is made clear that remarkable heat resistance property can be obtained by addition of Ni element in Al matrix composites.

• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1824-1832
• /
• 1992

본 연구에서는 충돌입자의 크기의 영향을 평가하기 위하여 동일한 운동에너지 를 갖는 직경 5mm 및 10mm의 강구를 시편에 충돌시킨 후 배항각 변화에 따른 손물역의 크기 변화를 초음파현미경(SAM)과 주사전자현미경(SEM)으로 관찰하였고, 충돌에 따른 압축강성의 변화를 고찰하기 위하여 충격전후의 압축탄성계수를 측정하였다.

• 한국주조공학회지
• /
• 제17권2호
• /
• pp.170-179
• /
• 1997

A noble technique has been developed for fabricating in situ formed $TiC_p/Al$ composites. In this process, fairly stable TiC particles were in situ synthesized in liquid aluminum by the interfacial reaction between an Al-Ti melt and SiC, which is a comparatively unstable carbide from the view-point of thermodynamics. It is possible in the present process to generate TiC particles of nearly 1 ${\mu}m$ in diameter, even utilizing SiC of 14 ${\mu}m$ as raw material. However, the dispersion behavior of TiC particles in the matrix depends on the size of the raw material SiC. Decomposing finer SiC makes the dispersion of TiC particles more uniform and the mechanical properties of composites are improved accordingly. The structure of in situ composites and their mechanical properties are affected by the fabrication temperature and the stirring time. It has been found that the most suitable condition for fabrication should be applied depending on the size of the raw material, even if the same kinds of carbide are used. Furthermore, although Al-Ti-Si system intermetallic compounds are detected in a $TiC_p/Al-Si$ composite which is fabricated by conventional melt-stirrng method, these compounds can not be observed in a $TiC_p/Al-Si$ composite made by this in situ production method. Hence the mechanical properties of the in situ $TiC_p/Al-Si$ composite are superior to those of the conventional $TiC_p/Al-Si$ composites.

• 한국재난정보학회 논문집
• /
• 제10권1호
• /
• pp.40-48
• /
• 2014

최근 철도의 고속화와 효율적인 기존철도 노선의 활용화가 요구됨에 따라 다양한 철도노반의 강화에 대한 시도가 진행되어 왔다. 그 중 지오그리드는 기존의 연구들을 통해 보강효과가 있음이 인지되어왔고 이에 활용범위가 늘어나고 있다. 본 논문에서는, 물성치가 다른 노반재료들로 구성된 궤도하부 노반을 형성 후 두 종류의 지오그리드를 각각 설치하고, 상재하중에 대한 인발강도에 미치는 영향을 알아보았다. 실험결과 인발강도와 상재하중은 비례하는 경향을 보여준 반면, 상호작용 인발계수는 감소되었으며 이는 상재하중 크기뿐만 아니라 접속면에서의 마찰각, 격자와 입자간의 결합상태등 복합적인 영향을 받는 것으로 판단된다. 또한, 일-에너지 개념을 이용한 지오그리드 효과를 산정하는 방법을 제시하였고 제한적으로 실험결과를 이용하여 검증하였다.