• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.12
• /
• pp.7-12
• /
• 2008

In this paper, a highly efficiency power amplifier is presented for multi-band antenna system. The class F power amplifier operating in dual-band designed with one LDMOSFET. An operating frequency of power amplifier is 900 MHz and 2.14 GHz respectively Matching networks and harmonic control circuits of amplifier are designed by using the unit cell of composite right/left-handed(CRLH) transmission line(TL) realized with lumped elements. The CRLH TL can lead to metamaterial transmission line with the dual-band holing capability. The dual-band operation of the CRLH TL is achieved by the frequency offset and the nonlinear phase slope of the CRLH TL for the matching network of the power amplifier. Because the control of all harmonic components for high efficiency is very difficult, we have controled only the second- and third-harmonics to obtain the high efficiency with the CRLH TL. Also, the proposed power amplifier has been realized by using the harmonic control circuit for not only the output matching network, but also the input matching network for better efficiency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.814-820
• /
• 2015

In this paper, A high selective dual-band bandpass filter was proposed using a dual-mode ring resonator with two short-circuited stubs. For dual-mode resonance, the ring resonator is directly connected with non-orthogonal feed-lines via coupling capacitors. Two short-circuited stubs which are unequal lengths are simultaneously placed at two corners along the two symmetry plane of the ring resonator in order to obtain dual-band responses. Because the feeding angle perturbated ring resonator of the proposed dual-band bandpass filter has the symmetrical structure, Even/Odd mode analysis can be well applied to extract the scattering parameters and transmission zero frequencies. The proposed dual-band bandpass filter was designed and fabricated for WLAN(Wireless Local Area Network) application of IEEE 802.11n standard. The measured results showed a good agreement with the simulation results, and it should be well applied not only for WLAN applications but also for any other communication systems.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.499-508
• /
• 2017

A new digital pre-distortion technique to linearize power amplifier (PA) is proposed for concurrent dual-band transmitters. In the conventional dual-band DPD techniques, two independent dual-feedback paths are required to compensate nonlinear cross-products between different bands as well as the nonlinear self-products of each band's own signal. However, it increases hardware complexity and expense. In this paper, we propose a new DPD method requiring only a single feedback path. In this new structure, the proposed technique first estimates the dual-band PA characteristics using the single feedback path. The DPD parameters are then extracted from the estimated PA characteristics. The DPD performance of the proposed method is validated through computer simulation. According to the results, the proposed technique can achieve comparable performance to the conventional two feedback DPD with significantly reduced hardware complexity.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.2
• /
• pp.259-268
• /
• 2023

In this paper, it is said that the quality of wireless service has been improved by providing wireless service that can eventually overcome wired wires by using 2.4GHz band wireless access technology that supports 2.4/5GHz dual band. Increasing the maintenance cost incurred when building wireless CCTV, makes it possible to connect with existing CCTV, and study about expanding the service area of A/V surveillance system using CCTV.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.5
• /
• pp.755-760
• /
• 2023

In this paper, the 2.4/5GHz dual band was used to ensure the reliability and stability of the wireless AV surveillance system using the existing 2.4GHz band. The proposed system supports dynamic channel allocation and channel change technology to avoid interference from other signals (Wifi, Bluetooth, etc.), reduces maintenance costs incurred when building wireless CCTV, and can be linked with existing wired CCTV. The service area of the A/V surveillance system used can be expanded.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.11
• /
• pp.32-36
• /
• 2008

In this paper, we investigate the capacity of CDMA/TDD in the inner zone of multimode scenario with dual-band operation where high frequency band is used for TDD in the inner zone and lower frequency band is utilized for FDD in the outer zone. The effects of various system parameters such as cell radius, date rate, and time slot allocation are analyzed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.6
• /
• pp.105-112
• /
• 2010

Recently, wireless communication systems have been developed and the circuits which operate with the broad-band for multiband uses were introduced. However, broad-band circuits have problems that inevitably increase the size. Dual-band circuit operates only two frequency, therefore, it will be able to miniaturize through unnecessary decreased elements. The Wilkinson power divider is the one of the most commonly used components in wireless communication system for power division. Nowaday, the Wilkinson power divider is also demanded dual-band. In this paper, I propose miniaturized dual-band Wilkinson power divider operating at 2.45 GHz and 5.2 GHz for IEEE 802.11n standard. Proposed dual-band Wilkinson power divider is used in parallel stub line. The design is accomplished by transforming the electrical length and impedance of the quarter wave sections of the conventional Wilkinson power divider into dual band ${\pi}$-shaped sections.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2004.06a
• /
• pp.101-105
• /
• 2004

본 논문에서는 온도 센서로부터 얻어지는 데이터를 전송하고 실시간으로 처리하기 위하여 RF방식을 이용한 단 방향 데이터 전송 시스템을 설계하고 그 특성을 측정하였다. 설계된 무선 전송기능의 온도 측정 시스템은 온도센서 및 제어부, 데이터 전송용 RF module로 구성되었다. 온도 측정을 위한 센서는 AD590 전류 구동 형 전압출력 센서이며 제어부는 PIC one-chip microprocessor를 사용하였다. 또한 데이터의 무선 전송을 위해 433MHz 주파수 대역의 반 이중 RF Module을 사용하여 system을 구현하였다. 실험은 10M 이내의 실내 공간 내에서 수행되었고, 임의의 온도측정 구간에 따른 온도 변화 환경에서 3가지 경우의 (3M,5M,10M) 거리 변화를 두고 데이터를 측정 및 비교 분석하였다. 실험결과 10M 이내의 거리에서는 온도센서로부터 얻어진 데이터를 실시간으로 송수신하여 결과를 처리할 수 있었으며 이를 이용한 다중 Sensor 시스템 구현이 가능한 결과를 얻었다.

• 전자공학회논문지 IE
• /
• v.47 no.2
• /
• pp.60-65
• /
• 2010

In this paper, we propose a dual-band filtering method optimized to DBO-CSS systems which are alternatively transmitted in low and high bands. The conventional channel filter which passes entire signal bandwidth causes a problem that excessive noise in neighboring sub-band is added while one of signals in two sub-bands is received. The dual-band filtering proposed in this paper can overcome the performance degradation in the conventional filtering method without increase of hardware complexity. The proposed method is based on two filters to be matched with DBO-CSS signals receiving alternatively and can exclude the undesired noise in neighboring sub-band. Simulation results for the proposed method show better performance about 2.5dB than the conventional one.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.1
• /
• pp.252-264
• /
• 2023

This paper proposes a design of a dual-band band-pass filter that integrates a λg/2 open SIR structure, a transmission line, and a fork-type structure with symmetric and asymmetric open stubs. To obtain the dual-band effect, the proposed filter uses the SIR structure and adjusts the impedance ratio of the SIR structure. Therefore, the position of the harmonics of the filter is shifted through the adjustment of the impedance ratio, and this can obtain a double-band effect. In order to obtain the dual-band characteristics, the dual-band effect is obtained by inserting a open stub between the SIR structures with the SIR structure divided in half. In addition, the second frequency response is obtained by adjusting the length of the open symmetrical stub in the fork-shaped structure. The asymmetrical open stub in the fork form achieves optimum bandwidth by adjusting the length. Therefore, the first center frequency of the proposed band-pass filter is 5.896 GHz and the bandwidth is 13.6 %. At this time, the measurement results are 0.13 dB and 33.6 dB. The second center frequency is 5.906 GHz and the bandwidth is 13.6 %. At this time, the measurement results are 0.15 dB and 19.8 dB. The reason is that when the impedance ratio (Δ) is higher than 1, the position of the harmonic is shifted to a lower frequency band. However, if the impedance ratio (Δ) is lowered by one step, the position of harmonics will move to a higher frequency band. The function of the filter designed using these characteristics can be obtained from the measurement result. The proposed band-pass filter has no coupling loss and no via energy concentration loss because there is no coupling structure of input/output and no via hole. Therefore, system integration is possible due to its excellent performance, and it is expected that dedicated short-range communication (DSRC) system applications used in traffic communication systems will be possible.