• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.4
• /
• pp.10-18
• /
• 2018

The primary purposes of this study are to understand a fundamental aspect of current uniformity around a reinforcing bar (rebar) in cement mortar, and to develop an accurate monitoring method in a wet-dry cycling process with the alternative current (AC) impedance method. Three cement mortar specimens with two embedded rebars were prepared in the laboratory. As a main variable, the distance between two rebars was designed to be 10, 20 and 30 mm with the same thickness of 20 mm. To simulate the corrosion of rebars in concrete structures in a marine environment, three cement mortar specimens were exposed to 15 wet-drying cycles (24-hour-immersion in seawater and 48-hour-drying in a room temperature) in the laboratory. It was observed that the potential level shifted to a noble value during corrosion potential monitoring, which is attributed to acceleration of dissolved oxygen diffusion at the drying process. AC impedance was measured in a frequency range from 100 kHz to 1 mHz on a wet-drying process. A theoretical model was proposed to explain the interface condition between the rebars and cement mortar by using the equivalent circuit consisting of a solution resistance, a charge transfer resistance and a CPE (constant phase element). It was observed that the diffusion impedance appeared in a low frequency range as corrosion of rebars progresses. At the drying stage of the wet-drying cycles, the currents line for monitoring tended to be non-uniform at the interface of rebar/mortar, being phase shift, ${\theta}$, close to $-45^{\circ}$.

• Proceedings of the Safety Management and Science Conference
• /
• 1999.11a
• /
• pp.343-343
• /
• 1999

아크용접은 산업전반에 걸쳐 그 생산기반에 없어서는 안될 필수기술로써 자동차 및 조선, 항공우주산업에 이르기까지 경제기반에 미치는 파급효과가 매우 크다. 그러나 이 아크용접을 하게 되면 각종 가스와 미세입자로 이루어진 흄이 발생하게 되는데 이들은 작업자들의 건강에 많은 영향을 미치는 것으로 보고되어 있다. 용접흄에는 용접재료 및 용접공정에 따라 다양한 유해원소가 포함되어 있고 그 종류에 따라 인체에 미치는 잠재적 독성효과도 매우 광범위하다. 최근 국내에서는 용접사들 중에 용접흄에 포함된 중금속 중 Mn중독에 의한 파킨스씨병 환자들과 Cr중독에 의하여 콧속 연골에 구멍이 뚫리는 비중격천공(鼻中隔穿孔) 환자들이 직업병으로 판정 받아 산재요양이 승인된 사례가 있다. 이러한 계기로 인하여 용접사들의 용접기피 현상이 심화되고 작업환경에 대한 법적규제는 선진 외국뿐만 아니라 국내에서도 한층 엄격하게 강화되고 있는 실정이다. 따라서 이제는 작업자와 사용자 모두 용접흄에 대한 인식의 전환이 요구되는 때이며 여러 분야에서 이러한 용접흄에 대한 연구가 활발히 진행되어야 한다. 해외에서는 이미 용접흄에 대한 연구가 활발히 진행되어 왔으나 국내의 경우는 매우 미비한 상태이며 용접산업의 미래 영향력이나 필요성을 고려할 때 국내에서도 적극적인 관심을 가져야 할 부분으로 판단된다. 본 연구에서는 아크용접공정에서 발생하는 흄의 특정 중금속 성분이 인체에 치명적인 악영향을 미치는 것에 착안하여 여러 종류의 용접재료에서 발생되는 용접흄의 중금속 분포를 조사하여 비교하였다. 이것은 향후 용접재료별 및 용접공정별 발생되는 흄의 유해원소를 저감시킬 수 있고 또한 각종 유해원소의 노출기준 및 평가기준을 마련할 수 있는 기초data로써 도움이 되리라 사료된다.동, 공정중재고가 줄어드는 결과를 보였고, 가동률 수준이 높을수록 ORR 방법간의 차이가 크게 나타났다. 그리고 부하평준화 기능은 Order Release 정책의 유효성에 별 영향을 주지 않는 것으로 나타났다. 결론적으로, Order Release 방법은 우선순위규칙간의 성능차이를 줄이거나, 대체할 수 통제 기법이라기보다는 우선순위규칙을 보완하여 공정중재고와 작업현장에서의 리드타임, 리드타임의 편차를 줄여주는 역할을 한다고 볼 수 있다. 그리고, 계획시스템이 존재하여 계획오더가 일정기간간격으로 이송되는 환경에서 특히 유용하다는 결론을 얻었다. 알 수 있었다. 것인데, 제조업에서의 심각한 고비용, 저효율 문제 를 해결하기 위해 필수적으로 도입해야만 하는 실정이다. 또한 소비자의 다양한 요구로 인 하여 제품의 종류와 사양면에서 심한 변동을 보이는 시장 수요에, 신속한 정보처리로 대응 하는데도 크게 기여하고 있다. 이에 본 연구에서는, 자동차 Job Shop의 동기화 생산방식을 지원하는 동기화 생산시스템의 구축 모델을 제시하고자 한다.과로 여겨지며, 또한 혈청중의 ALT, ALP 및 LDH활성을 유의성있게 감소시키므로서 감잎 phenolic compounds가 에탄올에 의한 간세포 손상에 대한 해독 및 보호작용이 있는 것으로 사료된다.반적으로 홍삼 제조시 내공의 발생은 제조공정에서 나타나는 경우가 많으며, 내백의 경우는 홍삼으로 가공되면서 발생하는 경우가 있고, 인삼이 성장될 때 부분적인 영양상태의 불충분이나 기후 등에 따른 영향을 받을 수 있기 때문에 앞으로 이에 대한 많은 연구가 이루어져야할 것으로 판단된다.태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(min

• Journal of Korean Society of Forest Science
• /
• v.110 no.2
• /
• pp.266-279
• /
• 2021

This study applied the e-PBL (e-Project-based learning) method for "Urban Forest Management" courses in the Department of Forest Science at S University to progress in university forest education. e-PBL effectively motivates self-directed learning, problem-solving, communication skills, and learners' responsibility by enabling them to choose, design, and perform their projects. Due to the COVID-19 pandemic in 2020, learners were encouraged to use online media to carry out projects and submit presentations for the campus forest. Learners' educational effects were subsequently investigated through a five-point Likert scale. This study discovered a positive effect on learners' motivation and interest (4.17) through e-PBL. Learners responded that e-PBL also helped their understanding regarding the subject (4.17). In addition, this study provided evidence that the e-PBL method was helpful in problem-solving (4.25), communication (4.33), and decision-making skills (4.21). According to learners' responses, there are positive indications that learners were satisfied with e-PBL. Learners responded that interactions and communications with team members could improve their understanding of the subject. Hence, there is scope for improving an efficient and successful e-PBL model suitable for university forest education by providing more efficient instructional time management, e-PBL method guidelines, and institutional support.

• Journal of Chest Surgery
• /
• v.43 no.6
• /
• pp.596-601
• /
• 2010

Background: This study was designed to evaluate the efficacy of a mixture of hyaluronic acid and sodium carboxymethyl cellulose ($Guardix-sol^{(R)}$) on experimental pericardial adhesion. Material and Method: Thirty rats were divided into 2 groups of 15 rats each and pericardial mesothelial injury was induced during surgery by abrasion. In the control group, blood and normal saline were administered into pericardium; in the test group, blood and HA-CMC solution were administered. Pericardial adhesions were evaluated at 2 weeks (n=5), 4 weeks (n=5), and 6 weeks (n=5) after surgery. The severity of adhesions was graded by macroscopic examination, and the adhesion tissue thickness was analyzed microscopically with Masson trichrome stain and an image processing program. Result: The test group had significantly lower macroscopic adhesion scores ($2.9{\pm}0.6$ : $3.9{\pm}0.4$, p<0.000) compared with the control group. For microscopic adhesion tissue thickness, the test group had lower scores compared with the control group, but this difference was not statistically significant ($91.73{\pm}49.91$ : $117.67{\pm}46.4$, p=0.106). Conclusion: We conclude that an HA-CMC solution ($Guardix-sol^{(R)}$) reduces the formation of pericardial adhesions in this animal model.

• Journal of Korea Water Resources Association
• /
• v.41 no.12
• /
• pp.1219-1230
• /
• 2008

Stream inflows induced by flood runoffs have a higher density than the ambient reservoir water because of a lower water temperature and elevated suspended sediment(SS) concentration. As the propagation of density currents that formed by density difference between inflow and ambient water affects reservoir water quality and ecosystem, an understanding of reservoir density current is essential for an optimization of filed monitoring, analysis and forecast of SS and nutrient transport, and their proper management and control. This study was aimed to quantify the characteristics of inflow density current including plunge depth($d_p$) and distance($X_p$), separation depth($d_s$), interflow thickness($h_i$), arrival time to dam($t_a$), reduction ratio(${\beta}$) of SS contained stream inflow for different flood magnitude in Daecheong Reservoir with a validated two-dimensional(2D) numerical model. 10 different flood scenarios corresponding to inflow densimetric Froude number($Fr_i$) range from 0.920 to 9.205 were set up based on the hydrograph obtained from June 13 to July 3, 2004. A fully developed stratification condition was assumed as an initial water temperature profile. Higher $Fr_i$(inertia-to-buoyancy ratio) resulted in a greater $d_p,\;X_p,\;d_s,\;h_i$, and faster propagation of interflow, while the effect of reservoir geometry on these characteristics was significant. The Hebbert equation that estimates $d_p$ assuming steady-state flow condition with triangular cross section substantially over-estimated the $d_p$ because it does not consider the spatial variation of reservoir geometry and water surface changes during flood events. The ${\beta}$ values between inflow and dam sites were decreased as $Fr_i$ increased, but reversed after $Fr_i$>9.0 because of turbulent mixing effect. The results provides a practical and effective prediction measures for reservoir operators to first capture the behavior of turbidity inflow.

• Journal of Chest Surgery
• /
• v.31 no.10
• /
• pp.919-923
• /
• 1998

Background: Calcific degeneration is unavoidable in either homo- or heterografts implanted in the human body. We have developed a calcification-resistant cardiovascular tissue patch using a novel technique of anticalcification. Materials and methods: Fresh bovine pericardium was harvested at the slaughter house and transfered to the laboratory in Hank's solution. After trimming and fixing the pericardium, it was embedded in 4$^{\circ}C$ 0.65% glutaraldehyde for a week and then washed by phosphate-buffered saline(PBS) of pH 7.4. This prepared pericardium was then stored in 2.5% sulphonated polyethyleneoxide(PEO-SO3) solution for 2 days at room temperature and reversed by 4$^{\circ}C$ NaBH4 solution for 16 hours. To evaluate the calcification-resistance of surface modified bovine pericardium with PEO-SO3, either glutaraldehyde- treated(GA group, n=4) or PEO-SO3-treated pericardial patch(PEO-SO3 group, n=4) was implanted into adult mongrel dog to reconstruct the main pulmonary artery and the descending aorta using a partial clamp technique. After 1 month follow-up, the implanted patches were retrieved to evaluate the pathologic findings and the content of calcium and phosphorous. Results: The PEO-SO3 group showed substantially less retraction and significantly less calcium deposition than the GA group in both aortic(7.10$\pm$1.05 vs. 13.81$\pm$2.33 mg/g of dried tissue) and pulmonary positions(1.55$\pm$0.29 vs. 6.72$\pm$0.70 mg/g)(p<0.01). Phosphorous contents were also less in the PEO-SO3 group than the GA group significantly, 8.11$\pm$1.07 mg/g vs. 19.33$\pm$4.31 mg/g in the aortic and 2.58$\pm$0.40 vs. 12.60$\pm$3.40 mg/g in thepulmonary position(p<0.01). Conclusions: These findings suggest that PEO-SO3 modified bovine pericardium is highly calcification-resistant but further study is needed to evaluate the long-term biological safety and compatibility of the prosthesis.

• Food Science and Preservation
• /
• v.22 no.5
• /
• pp.652-659
• /
• 2015

The physical properties of wheat kernels were determined as a function of moisture content to optimize the design of equipment for post-harvest management. Several properties, including bulk density, dynamic repose angle, one thousand-kernel weight, specific gravity, length, width, thickness, and area of two wheat cultivars (Baekjjung: B and Jogyeong: J ), were studied in the moisture range from approximately 9% to 30% wet basis. As moisture increased, length increased linearly from 6.42 to 7.20 mm (B) and 8.71 to 9.15 mm (J), width increased from 2.90 to 3.49 mm (B) and 4.12 to 4.43 mm (J), thickness from 2.94 to 3.20 mm (B) and 3.29 to 3.63 mm (J), and area from 14.13 to $19.44mm^2$ (B) and 27.75 to $31.25mm^2$ (J). Additionally, the dynamic repose angle and one thousand-kernel weight increased linearly from $46.3^{\circ}$ to $54.0^{\circ}$ (B) and $46.3^{\circ}$ to $54.5^{\circ}$ (J) and from 32.26 to 41.51 g (B) and 45.30 to 63.07 g (J), respectively, as the moisture content increased. Based on the experimental measurements, only the bulk density and specific gravity decreased from 754.0 to $664.1kgm^{-3}$ (B) and 776.1 to $660.0kgm^{-3}$ (J) and from 1.2950 to 1.2265 (B) and 1.3379 to 1.2671 (J), respectively, as moisture content increased.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.6
• /
• pp.603-616
• /
• 2023

In this study, machine learning-based clustering and classification of residential noise in apartment buildings was conducted using frequency and temporal characteristics. First, a residential noise source dataset was constructed . The residential noise source dataset was consisted of floor impact, airborne, plumbing and equipment noise, environmental, and construction noise. The clustering of residential noise was performed by K-Means clustering method. For frequency characteristics, L_eq and L_max values were derived for 1/1 and 1/3 octave band for each sound source. For temporal characteristics, Leq values were derived at every 6 ms through sound pressure level analysis for 5 s. The number of k in K-Means clustering method was determined through the silhouette coefficient and elbow method. The clustering of residential noise source by frequency characteristic resulted in three clusters for both L_eq and L_max analysis. Temporal characteristic clustered residential noise source into 9 clusters for L_eq and 11 clusters for L_max. Clustering by frequency characteristic clustered according to the proportion of low frequency band. Then, to utilize the clustering results, the residential noise source was classified using three kinds of machine learning. The results of the residential noise classification showed the highest accuracy and f1-score for data labeled with L_eq values in 1/3 octave bands, and the highest accuracy and f1-score for classifying residential noise sources with an Artificial Neural Network (ANN) model using both frequency and temporal features, with 93 % accuracy and 92 % f1-score.