• The Journal of Engineering Geology
• /
• v.11 no.2
• /
• pp.215-227
• /
• 2001

The Okchon Formation and the Mesozoic granite of the Boeun, Chungbuk are compared in terms of seismic wave velocities estimated from the field experiment, and seismic wave velocities in 3-D measured from the rock specimen. P-wave velocity for the field data ranges from 861 m/s (Guryongsan-2 Formation) to 2697m/s (Bulguksa Granite). P-wave anisotropy also ranges from 46% (Changri Formation) to 81% (Bulguksa Granite), with an average value of 68.5%. P-wave velocities for the rock specimens from Guryongsan-1, Guryongsan-2, Changri, and Munjuri Formations are greater than 5000m/s. S-wave velocities for those specimens are approximately 3500m/s, which is 3-5 times grater than the ones estimated from the field experimental data. P-wave anisotropy for the specimens from Bulguksa Granite and Guryongsan-1 Formation exceeds 60%, which is compared to 30% for the other specimens. This value is much smaller than average P-wave anisotropy (69.5%) for the field data. It is suggested that velocity difference, associated with the propagation direction, is much greater for the field data than for the specimens.

• Journal of Conservation Science
• /
• v.30 no.4
• /
• pp.467-480
• /
• 2014

This study was focused on measurement methods for stone cultural heritages by analyzing Ultrasonic (P-wave) velocity variations according to the water content and anisotropy of rocks. As a result of analyzing of rock properties, the water content and saturation degree were rapidly changed at the beginning of drying and then showed exponential curve which their rates of change gradually decreased. However, P-wave velocity and its rate of change maintained constant values after natural drying of 10 hours. Therefore, the ultrasonic measurement for stone cultural heritages should be performed after natural drying of 10 hours considering the weather and moisture conditions. In addition, the highest values of anisotropy coefficient exhibited in granite and limestone, and indirect method was insensitive to anisotropy compared to direct method. However, all rocks remained anisotropy by indirect method. Accordingly, ultrasonic measurement considering various directions is required. The research results will contribute to customized non-destructive testing and precise diagnosis for lithological characteristics of stone cultural heritage.

• The Journal of Engineering Geology
• /
• v.14 no.3 s.40
• /
• pp.273-285
• /
• 2004

The mechanical properties of the Cretaceous tuff distributed in the Goheung area were measured in the laboratory. Tuff (Goehung tuff and Palyeongsan welded tuff) in the study area is classified into vitric tuff with regard to its composition. The specific gravity, the dry density, the water content, the porosity and absorption ratio in tuffs of the study area are 2.51, $2.52(g/cm^2)$, 0.12($\%$), 4.51($\%$) and 1.91($\%$) in means, respectively. In the tuffs, dry densities are in inverse Proportion to Porosities, and absorption ratios are highly proportional with Porosities. The uniaxial compressive strengths(UCS) in the tuffs ranges from 80.4 to 208(MPa) and the average of the strength is 141.1(MPa). According to the engineering classification of intact rock (Deere & Miller, 1966), the tuffs are assigned to the high strength rocks. The point load strength index ($Is_a$) in axial test is 4.2(MPa) on the average, and the point load strength index ($Is_d$) in diametral test is 2.2(MPa) in mean, and the point load strength anisotrophic index($Ia_{(50)}$) by the ratio of $Is_a$ to $Is_d$ is 1.93. There is close linear correlation between the uniaxial compressive strength and point load strength index, and the equation representing the correlation is postulated as follows : UCS = 22 $Is_{(50)}$ +49 (MPa) (r=0.95). It is considered that this equation is a useful tool to estimate UCS for tuff in Goheung area.

• Transactions of Materials Processing
• /
• v.23 no.5
• /
• pp.311-316
• /
• 2014

In the current study, the R-value behavior of a two-layer clad steel was investigated using finite element analysis. Hill's 1948 anisotropic yield equation was employed to characterize the anisotropic behavior of the steel with different assumed properties: isotropic (R=1) and anisotropic (R=2). Experimental R-values were determined by measuring the width and thickness ratios of tensile specimens. Finite element analysis results demonstrate a difference in strain behavior in the width and the thickness directions of the clad steel. The R-value behavior depends on the fraction of the clad materials and total elongation.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.26 no.4
• /
• pp.327-344
• /
• 2024

In general tunnel design and analysis, rock masses are often assumed to be isotropic. Under isotropic conditions, material properties are uniform in all directions, leading to a higher evaluation of tunnel stability. However, actual rock masses exhibit anisotropic characteristics due to discontinuities such as joints, bedding planes, and faults, which cause material properties to vary with direction. This anisotropy significantly affects the stress distribution during tunnel excavation, leading to non-uniform deformation and increased risk of damage. Therefore, thorough pre-analysis is essential. This study analyzes the displacement and stress changes occurring during tunnel excavation based on rock anisotropy. A three-dimensional numerical analysis was performed, selecting anisotropy index and dip angles as variables. The results showed that as the anisotropy index increased, the displacement in the tunnel increased, and stress concentration became more pronounced. The maximum displacement and shear stress were observed where the dip planes met the tunnel.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.378-382
• /
• 2008

Since the sheet metal forming of Mg alloy is perform at elevated temperature, the effect of strain rates related with the forming temperature and forming speed and R-value is very important factor for formability and forming limits and deep drawing. It is investigated that the effect of material properties such as various temperature, forming speed and strain rates on formability and R-value of Mg alloy sheet in round cup deep drawing. Therefore, the investigation for process variables is necessary to improve formability and forming limits and deep drawing. Also, the effects of strain rate and drawbility were studied by the experiment. The temperature, forming speed, and strain rates and R-value are investigated. Forming of Mg alloy takes consider into temperature, proper forming speed and strain-rate and R-value the formed parts were good without defects for forming limits and deep drawing.