• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.4
• /
• pp.354-359
• /
• 2014

The objective of this study is to examine the fatigue behavior in compression of normal-weight and lightweight concrete mixtures with high volume supplementary cementitious material(SCM). The selected binder composition was 30% ordinary portland cement, 20% fly-ash, and 50% ground granulated blast-furnace slag. The targeted compressive strength of concrete was 40 MPa. For the cyclic loading, the constant maximum stress level varied to be 75%, 80%, and 90% of the static uniaxial compressive strength, whereas the constant minimum stress level was fixed at 10% of the static strength. The test results showed that fatigue life of high volume SCM lightweight concrete was lower than the companion normalweight concrete. The value of the fatigue strain at the maximum stress level intersected the descending branch of the monotonic stress-strain curve after approximately 90% of the fatigue life.

• Composites Research
• /
• v.14 no.3
• /
• pp.32-41
• /
• 2001

Z-section composite stringers with various lengths and flange-widths are tested in axial compression for the validation of a finite element algorithm to calculate the buckling and crippling stresses of composite laminated stringers. The stacking sequence considered is $[{\pm}45/0/90]s$. Strain gages are attached to each specimen, and deflection and end-shortening are obtained by two LVDTs. The buckling load is determined from the load vs. strain response, load vs. end-shortening curves, and load vs. out-of-plane deflection curves. The ultimate stress after local buckling is used as the crippling stress. Comparison between finite element and experimental results shows good agreement in the local buckling and crippling stresses.

• Elastomers and Composites
• /
• v.44 no.4
• /
• pp.423-428
• /
• 2009

The non-Newtonian flow curves of polyurethane melts were obtained by using a Physica cone-plate rheometer at various temperatures. The rheological parameters were obtained by applying non-Newtonian flow equation to the flow curves for polyurethane samples. When the polyurethane samples are under increasing-decreasing shear rate modes, the hysteresis loop and thixotropic behavior were shown. Polyurethane melts behave as strong gels when they are subjected to shear flow, but when the applied stress surpasses the yield stress, they exhibit non-linear viscoelasticity. Upon decreasing shear rate, its shear stress remains smaller than the values measured in the increasing shear rate mode, because of broken of its structure.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.5
• /
• pp.52-57
• /
• 2011

Most ships and offshore structures are equipped with a variety of pipes, which inevitably contain curved portions. While it has been a usual practice to conduct bending stress analyses of these curved pipes using the straight-beam theory, this paper adopts two different types of finite elements, straight-beam elements and two-dimensional shell elements, for finite element analyses of a variety of curved pipes. It then compares the analysis results for two different types of elements to determine correction factors, which can be used to transform the bending displacements and bending stresses obtained by straight-beam elements to those obtainable by two-dimensional shell elements. The paper ends with a practical suggestion on how to efficiently use these correction factors to estimate the combined axial and normal stresses in a curved portion of a pipe.

• Tunnel and Underground Space
• /
• v.10 no.1
• /
• pp.59-69
• /
• 2000

Acoustic emission is n burst of microseismic waves generated by microscopic failure due to deformation in materials. The study on the detection of initiation and propagation of microcracks from acoustic emission measurement is very important for the evaluation of the stability of underground rock structures by the nondestructive letting method. In this study, acoustic emission was measured under uniaxial stiffness loading test used to obtain the complete stress-strain curves of marble and concrete used as reinforced materials of rock structures. The analysis of acoustic emission parameters and source location were performed to discuss the characteristics of the deformation and failure behavior of rock and concrete. And acoustic emission was measured under cyclic loading test to verify the Kaiser effect associated with the damage of materials, in situ stress of rock, and stress history of concrete structure.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.5
• /
• pp.291-296
• /
• 2006

The residual stress in shot-peened Al 7075 alloy was evaluated using surface acoustic wave (SAW). Shot peening was conducted to produce a variation in the residual stress with the depth below the surface under a shot velocity of 30 m/s. The SAW velocity was measured from the V(z) curve using a scanning acoustic microscopy (SAM). The Vickers hardness profile from the surface showed a significant work hardening near the surface layer with a thickness of about 0.25 mm. As the residual stress became more compressive, the SAW velocity increased, whereas as the residual stress became more tensile, the SAW velocity decreased. The variation in the SAW velocity through the shot peened surface layer was in good agreement with the distribution of the residual stress measured by X-ray diffraction technique.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.5
• /
• pp.1897-1905
• /
• 2013

Rheological properties such as yield stress and viscosity is the main parameters to determine the fluidity of the debris flow. In this study, several series of rheometer tests were performed to investigate rheological properties of fine-grained soil samples with various sand contents and various liquidity indices. Test results indicated that the general shape of the flow curves for fine-grained soils had characteristics of a shear thinning fluid, with a decrease in viscosity as shear rate increases. The yield stress and viscosity of fine-grained soil samples with same sand content gradually decreased as the liquidity index increased. At the same liquidity index, yield stress and viscosity of fine-grained soil increased with an increase in sand content. The yield stress and viscosity of fine-grained soil greatly decreased with a slight increase in water content. Also, the yield stress and viscosity tend to increase with increasing concentration by volume($C_v$) of the fluid matrix. The values of the four coefficients ${\alpha}_1$, ${\alpha}_2$, ${\beta}_1$, and ${\beta}_2$ were obtained by regression analysis for each fine-grained soil.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.185-192
• /
• 2000

A novel indentation theory is proposed by examining the data from the incremental plasticity theory based finite element analyses. First the optimal data acquisition location is selected, where the strain gradient is the least and the effect of friction is negligible. This data acquisition point increases the strain range by a factor of five. Numerical regressions of obtained data exhibit that strain hardening exponent and yield strain are the two main parameters which govern the subindenter deformation characteristics. The new indentation theory successfully provides the stress-strain curve with an average error less than 3%.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.12
• /
• pp.87-105
• /
• 2009

Nonlinear dynamic deformation characteristics, expressed in terms of normalized shear modulus reduction curve (G/$G_{max}-\log\gamma$, G/$G_{max}$ curve) and damping curve (D-$\log\gamma$), are important input parameters with shear wave velocity profile ($V_s$-profile) in the seismic analysis of (new or existing) fill dam. In this paper, the reasonable and economical methods to evaluate the nonlinear dynamic deformation characteristics for core zone and rockfill zone respectively are presented. For the core zone, 111 G/$G_{max}$ curves and 98 damping curves which meet the requirements of core material were compiled and representative curves and ranges were proposed for the three ranges of confining pressure (0~100 kPa, 100 kPa~200 kPa, more than 200 kPa). The reliability of the proposed curves for the core zone were verified by comparing with the resonant column test results of two kinds of core materials. For the rockfill zone, 135 G/$G_{max}$ curves and 65 damping curves were compiled from the test results of gravelly materials using large scale testing equipments. The representative curves and ranges for G/$G_{max}$ were proposed for the three ranges of confining pressure (0~50 kPa, 50 kPa~100 kPa, more than 100 kPa) and those for damping were proposed independently of confining pressure. The reliability of the proposed curves for the rockfill zone were verified by comparing with the large scale triaxial test results of rockfill materials in the B-dam which is being constructed.

• Journal of the Korea Concrete Institute
• /
• v.24 no.1
• /
• pp.15-23
• /
• 2012

This paper is about proposal of a calculation method and development of an analytical program for predicting crack width and deflection in structural concrete members. The proposed method numerically calculate stresses in steel rebar using a parabola-rectangle stress-strain curve and a modified tension stiffening factor considering the effect of the cover thickness. Based on the study results, a calculation method to predict crack width and deflection in reinforced concrete flexural members is proposed utilizing effective tension area and idealized tension chord as well as effective moment-curvature relationship considering tension stiffening effect. The calculation method was applied to the test specimens available in literatures. The study results showed that the crack width and deflections predicted by the proposed method were closed to the experimentally measured data compared the current design code provisions.