• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.223-233
• /
• 2003

Sand compaction pile (SCP) is one of the ground improvement techniques which are being used for not only accelerating consolidation but also increasing bearing capacity of loose sands or soft clay grounds. In this study, laboratory model tests and 3-D finite element analyses were performed to investigate the interaction between sand compaction piles and surrounding soft soils. Based on the results obtained, as the area replacement ratio increases, the stress concentration ratio increases at the pile point, the settlement decreases, and the relative displacement between column and soil also decreases. It is also found that numerical study is illustrated by good comparison with model test results, and the numerical analysis revealed slip effects which could not be specifically identified in the model tests.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.11
• /
• pp.1125-1130
• /
• 2017

The tooth shapes of serration-type and spline-type reactors are optimized using finite element methods to improve the working life of the part and to lower the stress concentration during rotation resulting from contact with the outer race for a reactor operating with $170^{\circ}C$ transmission oil. The results of thermal expansion analyses between an Al reactor and the steel outer race indicate that, before optimization, the gap between the two parts increases further as the serration-type reactor expands by 0.1 mm and the spline-type one strains by 0.08 mm. Because of shape optimization, a trapezoidal shape is obtained from the initial triangular serration and the rectangular spline of the two reactors. The maximum von Mises stress of the serration-type convertor decreased by 24.5 ％, and by 9.3 ％ for the spline-type convertor. In addition, there is a 13 ％ reduction in the axial thickness, as compared to the initially designed model.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.1
• /
• pp.55-65
• /
• 2019

This paper describes results of experimental and numerical analyses, in order to analyze a reinforcement effect of concrete mat on open cut restoration of underground cavity. The plate loading tests were conducted to evaluate a reinforcement effect of concrete mat, at reinforcement depths from the ground surface of 10 cm, 20 cm, and 30 cm. The result showed that the reduction ratio of stress (earth pressure) was about 60% at all reinforcement depth. The reinforcement effect considering ground surface settlement and reduction ratio of stress based on laboratory tests and numerical analysis was significant, at reinforcement depths from the ground surface of 10 cm~20 cm. LFWD test results showed that subgrade modulus was the largest when concrete mat was installed 20 cm below ground surface. Therefore, it is effective to reinforce concrete mat within 20 cm from the surface, when the underground cavity due to damage of underground utilities was formed in the height direction to the bottom of the pavement layer.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.11
• /
• pp.5-14
• /
• 2007

In this study, Matsuda formula used to evaluate the loads acting on the pillar was investigated and load reduction factor(${\alpha}$) was evaluated by numerical analysis to better apply for the design. From the results, normal stress was concentrated to one side due to excavation of preceding tunnel after construction of pillar. And 86.5% of maximum normal stress was revealed partly unequally when the ground was poor. By numerical analysis, $14{\sim}83%$ of total loads calculated by Matsuda formula decreased and then, from these results, load reduction factor(${\alpha}$) was estimated. From now on, stability and economic aspects could be guaranteed by applying the load reduction factor(${\alpha}$).

• Korean Journal of Agricultural Science
• /
• v.14 no.2
• /
• pp.329-344
• /
• 1987

This paper described the behavior under repeated loading in triaxial compression test on clay. The experiment was conducted to investigate the influence of controlled various over-consolidation ratio and compaction energy, on the stress-strain behavior of clays. 1. The difference of deviator stress during repeated loading was greatly appeared at large strain. And pore water pressure was decreased at initial of unloading, but it was increased again before long. 2. The recoverable elastic strain (${{\Delta}{\varepsilon}e}$) and the slope of un-reloading were decreased with the increment of over-consolidation ratio (OCR). 3. The recoverable elastic strain (${{\Delta}{\varepsilon}e}$) was increased with the increment of strain rate but it was decreased with the increment of strain in strain rate tests. The slope of un-reloading (Eur) tends to increase with the increment of strain rate and it was decreased with the increment of strain. 4. The recoverable elastic strain was greatly increased with the increment of compaction energy and it slightly tends to decrease with the increment of strain on various compaction energy. The slope of un-reloading was not appeared markedly with increment of compaction energy but it tends to decrease with the increment of strain generally.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.9
• /
• pp.3148-3154
• /
• 2010

This paper presents the probabilistic analysis for fatigue life of Glass/Epoxy laminates with impact-induced damage. For this, a series of impact tests were perfomed on the Glass/Epoxy laminates using instrumented impact testing machine. Then, tensile and fatigue tests carried out so as to generate post-impact residual strength and fatigue life. Two Parameter Weibull distribution was used to fit the residual strength and fatigue life data of Glass/Epoxy composite laminates. The residual strength was affected by impact energy and their variance decreased with increasing of impact energy. The fatigue life of impacted laminates was greatly reduced by impact energy and this trend depended on applied stress amplitude. Additionally, the variation of fatigue life was gradually decreased with the applied stress amplitude.

• Composites Research
• /
• v.17 no.4
• /
• pp.1-6
• /
• 2004

In this paper, the importance of the size effects on the strength ratio is demonstrated by numerical results. The rate of decrease of tensile strength is for glass fiber, based on the experience of a composite manufacturing specialist. For other material, similar procedure may be used until detailed test result on such material is available. The strength criterion used is that of Tsai-Wu fur stress space. The factors influencing the ratio are, reducing the tensile strength alone or both tensile and compression strengths, selection of the normalized interaction term, that is, the generalized von Mises criterion or the Hill's criterion, and the status of applied stresses. Some of the numerical results are presented for a guideline for the future study.

• Composites Research
• /
• v.23 no.1
• /
• pp.23-30
• /
• 2010

Most of the bridge systems, including the girders, cross-beams, and concrete decks behave as specially orthotropic plates. In general, the analytical solution for such complex system is very difficult to obtain. In this paper presented, a design method of slab bridge of simple supported made by composite materials. For the design of bridge made by the composite materials, cross-section was used the form-core shape because of this shape is economical and profitable, and for output of the stress value used finite difference method. In this paper, the rate of tensile strength reduction due to increased size was considered. Strength-failure analysis procedure, using the reduced tensile strength, was presented. And also numerical study was made for these cases.

• Tunnel and Underground Space
• /
• v.24 no.1
• /
• pp.89-96
• /
• 2014

Rock joint surface roughness, which is known to be one of the most important factors for defining shear strength of rock mass, has been researched in various methods. However, approaches to separate a roughness into two groups (primary and secondary) for evaluating the roughness have been rarely performed. In this study, elements of secondary roughness were eliminated through direct shear testing with tensile joint specimen and they were quantified with joint parameters. It is revealed that roughness parameters decrease with increasing the normal stress and sampling intervals, except for the case in which the normal stress is larger than 1.5 MPa. Also it is analyzed that ratio of area reduction in the opposite direction of shearing decreases with increasing the roughness parameter.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.386-386
• /
• 2013

반도체 소자의 소형화, 고집적화로 박막의 다층화 및 선폭의 감소 등의 복잡한 제조 공정이 불가피하고, 따라서 공정 중 실리콘 웨이퍼와 금속 박막사이의 확산을 방지하기 위한 많은 연구가 이루어지고 있다. 하지만 현재까지의 연구는 확산방지막의 nano-mechanics 특성 분석에 대한 연구는 전무하다. 본 논문에서 tungsten (W)을 주 물질로, nitrogen (N)을 첨가한 확산방지막을 질소 유량을 2.5, 5, 7.5, 10 sccm으로 변화시켜가면서 rf magnetron sputter 방법으로 tungsten-nitride (W-N) 박막을 증착하였다. 박막의 기본 물성인 증착율, 비저항 및 결정학적 특성을 ${\beta}$-ray, 4-point probe, X-ray diffraction (XRD)를 이용하여 측정하였고, 측정결과 증착 중 질소 유량이 증가할수록 W-N 박막의 비저항은 증가하였고 반대로 증착율과 결정성은 감소하였다. 이는 기존의 연구 결과와 비교하여 일치한 결과로 증착된 박막이 신뢰성을 가짐을 확인하였다. 이후 가장 관심사인 nano-mechanics 특성은 nano-indenter를 이용하여 측정하였다. 측정 결과 시료는 증착 중 질소 유량이 2.5 sccm인 시료를 기준으로 5 sccm 포함된 박막에서 load force-depth 그래프가 급격히 변화하는 경향을 나타내었고, 표면강도(surface hardness)는 10.07 GPa에서 15.55 GPa로 증가하였다. 이후 질소 유량이 7.5 sccm과 10 sccm에서는 12.65 GPa와 12.77 GPa로 질소 유량이 5 sccm 포함된 박막보다 상대적으로 감소하였다. 이는 박막내 결정상으로 존재하는 질소와 비정질 상태로 존재하는 질소의 비율에 의한 것이고, 압축력에 기인하는 스트레스 증가로 판단된다.