• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.6
• /
• pp.361-374
• /
• 2016

When the seabed around and under gravity structures such as submerged breakwater is exposed to a large wave action long period, the excess pore pressure is generated significantly due to pore volume change associated with rearrangement soil grains. This effect leads a seabed liquefaction around and under structures as a result from decrease in the effective stress, and the possibility of structure failure is increased eventually. These facts shown above have been investigated in the previous studies related to regular and irregular waves. This study suggested a concrete mat for preventing the seabed liquefaction near the submerged breakwater. The concrete mat was mainly used as a countermeasure for scouring protection in riverbed. According to installation of the concrete mattress, the time and spatial series of the deformation of submerged breakwater, the pore water pressure, and the pore water pressure ratio in the seabed were investigated. Their results were also compared with those of the seabed unprotected with the concrete mat. The results presented were confirmed that the liquefaction potential of seabed under the concrete mattress is significantly reduced under regular wave field.

• Journal of Bio-Environment Control
• /
• v.15 no.2
• /
• pp.138-148
• /
• 2006

This study was carried out to evaluate the structural safety fur both the attached wind-protecting wall in greenhouse and the detached one installed outside. Regarding the attached wind-protecting wall in greenhouse, the analysis was conducted by doing a fluid-structure coupled field analysis using both CFX-5.7 and ANSYS 8.1 and also under the design condition of an instantaneous maximum wind velocity of $30.9m{\cdot}s^{-1}$. Three kinds of the width ranged from 30 to 90cm were considered in this study. With regard to the detached wind-protecting wall, the structural saffty was analyzed under the pressure difference of 1,117 Pa which corresponded to a wind velocity of $50m{\cdot}s^{-1}$ and the analytical results were also compared with theoretical ones. The result showed that there was little difference in the distribution of velocity overall and total pressure on the lateral side according to the width of the attached wind-protecting wall, but greenhouse with wind-protecting widths of 30 to 60cm has been reinforced to the extent of about 11% when compared with the case of being without the wall. The result also showed that the detached wind-protecting wall with a main-column interval of 3m was not stable so that it was necessary for the detached wind-protecting wall to be adequately reinforced to secure structural stability. Finally, there was great difference between analytical results and theoretical studies. The difference meant that there was some possibility of including errors when a theoretical study was done in three dimensional structure.

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.6
• /
• pp.101-111
• /
• 2006

In case of drilled shafts installed by drilling through soft overburden onto a strong rock, the piles can be regarded as end-bearing elements and their working load is determined by the safe working stress on the pile shaft at the point of minimum cross-section or by code of practice requirements. Drilled shafts drilled down for some depth into weak or weathered rocks and terminated within these rocks act partly as friction and partly as end-bearing piles. The base resistance component can contribute significantly to the ultimate capacity of the pile. However, the shaft resistance is typically mobilized at considerably smaller pile movements than that of the base. In addition, the base response can be adversely affected by any debris that is left in the bottom of the socket. The reliability of base response therefore depends on the use of a construction and inspection technique which leaves the socket free of debris. This may be difficult and costly to achieve, particularly in deep sockets, which are often drilled under water or drilling slurry. As a consequence of these factors, shaft resistance generally dominates pile performance at working loads. The efforts to improve the prediction of drilled shaft pile performance are therefore primarily concerned with the complex mechanisms of shaft resistance development. In this study, the numerical analyses are carried out to investigate the behavior characteristics of side of rock socketed drilled shafts varying the loading condition at the pile head. The difference of behavior characteristics of side resistance is also evaluated with the effects of modelling of asperity.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.7
• /
• pp.59-66
• /
• 2014

Nowadays, some studies are performed in order to introduce the Limit State Design method widely used in foreign work sites. LRFD (Load Resistance Factor Design) method is widely used in the fields in which the data accumulation is possible - such as deep foundations, and shallow foundations, etc. The limit state design in the retaining walls is insufficient in the country owing to difficulties applying load tests. The limit state design method for retaining wall structures are studied based upon the National Retaining wall Design Standard legislated in 2008 by Ministry of Land, Transport, and Maritime Affairs. In this paper several retaining walls were calculated according to LRFD design criteria analysis using the general program with limit state design method and the factor of safety for sliding and overturning. Comparing with their results, the Taylor's series simple reliability analysis was performed. In the analysis results of retaining wall section, safety factors calculated by LRFD were found to be lowered than those calculated in current WSD, and it is possibly judged to be economic design by changing wall dimensions. In the future, pre-assessment of the geotechnical data for ensuring the reliability and the studies including reinforced retaining walls with ground anchor are needed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.5
• /
• pp.287-296
• /
• 2020

The wave-impact load on offshore structures can be divided into green-water and wave-slamming impact loads. These wave impact loads are known to have strong nonlinear characteristics. Although the wave impact loads are dealt with in the current classification rules in the shipping industry, their strong nonlinear characteristics are not considered in detail. Therefore, to investigate these characteristics, wave-impact loads induced by a breaking wave on a circular cylinder were analyzed. A model test was carried out to measure the wave-impact loads due to breaking waves in a two-dimensional (2D) wave tank. To generate a breaking wave, the focusing wave method was applied. A series of 2D tank tests under a horizontal wave impact was carried out to investigate the structural responses of the cylindrical structure, which were obtained from the measured model test data. According to the results, we proposed a structural damage-estimation procedure of an offshore tubular member due to a wave impact load. Furthermore, a recommended wave-impact load is suggested that considers the minimum required thickness of each member. From the experimental results, we found that the required minimum thickness is dependent on the impact pressure located in a three-dimensional space on the surface of a tubular member.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.9
• /
• pp.167-176
• /
• 2004

Underground structures will be affected by the additional surcharge loads such as traffic load et al. Terzaghi (1956) suggested the equation on the influences of surcharge loads in vertically backfilled spaces. In field, the shapes of backfill spaces are not always formed vertically. Then the Terzagi (1956) equation is not suitable to use because of boundary condition. This study suggests equation to calculate the stress in backfilled space caused by surcharge loads when the backfilled space is sloped symmetrically. The suggested equation is verified by carbon box test and numerical analysis. The experimental results show good agreement with the suggested equation but the numerical analysis result shows a little disagreement. The differences are estimated to be caused by the fact that ground made by carbon rod has become more dense and internal frction and wall friction has increased itself as surcharge load is added but that this increase can not be considered in the numerical analysis. The suggested equation shows good agreement with Terzaghi (1956) equation in case of sloped backfill ground. According to the results, it is considered that the suggested equation can be applied not only to sloped space but also to vertical space. Further investigation using full scale experiment is needed.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.33-43
• /
• 2005

This work reports results of our study on the dynamic responses of the buried pipelines both along the axial and the transverse directions under various boundary end conditions. In order to investigate the effect of the boundary end conditions for the dynamic responses of the buried pipeline, we have devised a computer program to find the solutions of the formulae on the dynamic responses (displacements, axial strains, and bending strains) under the various boundary end conditions considered in this study, The dynamic behavior of the buried pipelines for the forced vibration is found to exhibit two different forms, a transient response and a steady state response, depending on the time before and after the transfer of a seismic wave on the end of the buried pipeline. We have observed a resonance when the mode wavelength matches the wavelength of the seismic wave, where the mode number(k) of resonance f3r the axial direction. On the other hand, we have not been able to observe a resonance in the analysis of the transverse direction, because the dynamic responses are found to vanish after the seventh mode. From the results of the dynamic responses at many points of the pipeline, we have found that the responses appeared to be dependent critically on the boundary end conditions. Such effects are found to be most prominent especially for the maximum values of the displacement, the strain and its position.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.248-252
• /
• 2010

홍수기 호우로 인한 피해는 대부분 하천구역에서 발생되며, 이러한 피해는 인간에게 직 간접적으로 영향을 미치게 된다. 자연 상태의 하천형상은 대부분 호우로 인한 홍수로 인해 자연스럽게 만들어지게 되며, 대부분 사행하천의 형태를 띠게 된다. 사행하천에서의 흐름의 기하학적 특성은 성장이나 사멸, 또는 두 가지 모두의 형태를 보인다. 사행하천에서의 흐름 및 유속 분포는 하천제방 보호, 주운, 취수, 그리고 유사 이동 및 퇴적 패턴과 관련하여 실용적인 관점에서 연구하여야 하는 하천수리학에서는 매우 중요한 주제이다. 그리고 사행하천은 특히 만곡부가 교호적으로 나타나는 곳에서의 흐름구조가 매우 복잡하다. 이러한 사행하천에서는 회전방향이 교호적으로 바뀌는 나선형의 흐름(2차류)이 3차원적으로 발생하는 것으로 알려져 있다. 본 연구에서는 사행하천이 많은 국내 하천특성을 고려하여, 하천 만곡부에서의 흐름특성을 분석하고자 하였으며 2차원 CCHE2D 와 3차원 FLOW3D 모형을 적용하였으며 가상 하도에 대하여 수리모형 실험의 실측치와 비교하여 모형의 정확성과 안정성을 검증하였다. 그리고 남강댐 하류에 대하여 만곡부의 흐름특성(유속 분포 및 최대유속경로, 수위분포, 2차류 거동, 편수위, 전단응력 분포 등)을 분석함으로써, 하천 만곡부에서의 수리적 특성을 보다 정확하게 제시하고자 한다. 모의 분석결과 동일 하도에 대하여 유량을 변동시킬 경우, 유량이 증가할수록 만곡부에서의 수리영향이 더욱 뚜렷해짐을 알 수 있었고 2차원 모형보다 3차원모형의 결과의 정확도가 더 높은 것으로 분석되었다. 곡률반경이 1,300~1,600 정도인 실제하천에 적용한 결과, 수위의 경우 2차원 결과가 3차원 결과보다 최대 3%정도 수위가 높은 것으로 나타났으며, 또한, 상관계수가 평균 0.91의 값을 보이고 있어 2차원모형과 3차원모형의 결과가 비교적 잘 일치하는 것으로 분석되었다. 흐름 분석을 통해서 만곡부에서의 최대유속은 최정점(apex)에서 보다는 오히려 최정점 이전 하도의 내측에서 발생하였으며, 정점에서의 종단유속은 감소하지만 횡단유속은 오히려 크게 증가하는 경향을 보이고 있었다. 따라서 하천설계시 사행하천의 제방 안정성 확보를 위하여 종단유속 뿐만 아니라 횡단유속 또한 고려할 필요가 있음을 확인하였다. 또한 남강댐 하류 만곡부에서의 내측 및 외측의 수위를 분석한 결과, 제방 외측의 수위가 평균수위에 비해 최대 약 37cm정도 증가하는 것으로 분석되었다. 따라서 만곡부에 대한 하천제방설계시 좌, 우안의 여유고를 일률적으로 적용하기 보다는 만곡에 따른 흐름특성을 분석하여 설계에 적용하여야 안정성 및 경제성을 동시에 확보할 수 있을 것으로 사료된다.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.8
• /
• pp.37-49
• /
• 2018

Since the observation of ground motions in South Korea, liquefaction manifestation was the first to be observed in Pohang earthquake in 2017 with $M_L$ 5.4. Because liquefaction causes ground settlement and lateral spread damaging in-ground or super structures, various researchers have been analyzing the Pohang liquefaction case history to better understand and predict liquefaction consequence and to prevent future disasters. In prior research at the 2018 EESK conference, a map of Liquefaction Potential Index (LPI), indicating the severity of liquefaction, in Pohang was created and compared with damage observations. The LPI correlated well with the observations, but the severity categorized by LPI range was significantly higher than the actual observations in most regions. The prior LPI map was created evaluating ground motions using the simplified approach. In this research, we perform the effective site response analyses with porewater pressure generation model for the detailed evaluation of liquefaction on the liquefied sites in Pohang. We found that the simplified approach for LPI evaluation can overestimate the severity.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.936-944
• /
• 2019

Submarines, which have been called an invisible force, are strategic underwater weapon systems that perform missions such as anti-surface warfare, anti-submarine warfare, and high payoff target strikes with the advantage of underwater covertness. A submarine should be able to withstand the hydrostatic pressure of the deep sea. In this respect, the submarine pressure hull, as the main structural system to resist the external pressure corresponding to the submerged depth, should ensure the survivability from hazards and threats such as leakage, fires, shock, explosion, etc. To do this, the initial scantling of the submarine pressure hull must be calculated appropriately in the concept design phase. The shape of the aft transition ring varies according to its connection with the submarine aft end conical structure, pressure hull cylindrical part, and non-pressure hull of the submarine; the design of the aft transition ring should not only take into account stress flow and connectivity but also the cost increase due to the increased man-hours of its complex geometry. Therefore, trade-off studies based on the four different shapes of the aft transition ring are carried out considering both the review of the structural strength through nonlinear finite element analysis (FEA) and economic feasibility by reviewing the estimations of the manufacturing working days and material costs. Finally, the most rational structural aft transition ring shape for a submarine amongst four reviewed types was proposed.