• Journal of computational fluids engineering
• /
• v.19 no.1
• /
• pp.41-46
• /
• 2014

The aerodynamic drag of high-speed train has been calculated and the effect of bogie side fairing on the aerodynamic drag has been investigated. Computational Fluid Dynamics (CFD) simulation based on steady-state 3 dimensional Navier-Stokes equation has been conducted employing FLUENT 12 and the aerodynamic model of HEMU-430x, the Korean next generation high-speed train under development has been built using GAMBIT 2.4.6. Three types of bogie side fairing configuration, the proto-type without fairing, half-covered fairing to avoid the interference with the bogie frame and full-covered fairing have been adopted to the train model to compare the drag reduction effects of the bogie side fairing configurations and the numerical results yields that the bogie side fairing can reduce the aerodynamic drag of the 6-car trainset up to 7.8%. The aerodynamic drag coefficient of each vehicle as well as the flow structures around the bogie system have also been examined to analyze the reason and mechanism of the drag reduction by bogie side fairing.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.11a
• /
• pp.218-219
• /
• 2018

쌍동선형은 단동선형에 비해 안정성 및 저항성능이 우수하며 그 형상은 일반적으로 대칭 및 비대칭으로 구분한다. 이러한 쌍동선은 고속으로 운항하는 경우 선체사이의 파랑 중첩현상을 줄이기 위해 주로 비대칭선형을 사용한다. 또한, 중소형선박은 선미터널을 적용하여 추력효율을 향상시킨다. 본 연구에서는 비대칭 고속 쌍동선의 선미터널 입구영역의 경사각 변화에 따른 유체역학적 특성(저항성능, 항주자세, 압력분포)에 대한 수치해석 연구를 수행하였다. 수치해석은 상용프로그램 STAR CCM+를 이용하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1301-1309
• /
• 1989

본 연구의 목적은 Lumley의 저항감소 모델을 사용하여 여러 부하도하에서 부유유동의 유동 특성을 관찰하는 것으로, 특히 저항감소가 일어날 때와 일어나지 않을 때의 유동특성을 알아 보고자 한다.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.588-592
• /
• 2016

선박의 최적 운항 자세를 찾기 위해 자유 수면을 포함한 저항 해석을 수행할 경우 많은 격자를 이용한 비정상 해석으로 인해 계산 시간이 오래 소요되는 단점이 있다. 본 연구에서는 이를 개선하여 이중 모형을 이용한 정상 해석을 통해 보다 효율적으로 선박의 최적 운항 자세를 도출하는 방법을 연구하였다. KCS를 대상선으로 선정하여 설계속도(24knots)와 저속(15knots)인 경우에 대하여 평형 상태 및 선수/선미 트림 상태에서 이중 모형 수치해석을 수행하고 기존의 연구결과와 비교하였다. 그 결과 자유수면 유무와 속도에 상관없이 선체 자세에 따른 저항 값은 동일한 경향을 갖는 것을 확인하였다. 하지만 저속일 경우 트림조건에 따른 저항의 변화의 폭에서 차이를 보였으며, 이는 압력저항에 기인한 것이다. 따라서 이중 모형을 이용한 저항 해석은 압력저항의 변동이 큰 경우에는 적용되기 어렵다는 한계점이 있다. 하지만 마찰 저항이 주요한 경우에 적용되어 계산효율을 획기적으로 높일 수 있으며, 정성적인 경향을 제시할 수 있는 타당한 방법이라 사료된다.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.08a
• /
• pp.132-138
• /
• 2003

The optimal design for a leading car considering the aerodynamic resistance is required on the high-speed train due to increasing of ratio of drag force with proportion for the square of velocity. The aerodynamic analysis using CFD in the stage of concept design offers more economical analysis method which is used to estimate the influence of flow and pressure around the leading car than the experimental method using the Mock-up. In this study, we want to assist the artistic design with aerodynamics analysis in order to get the optimal design for leading car with the operation speed of 180km/h. The results of aerodynamic analysis for two leading car models which one is expressed with lineal beauty and the other is with curvaceous beauty are compared with each other and they offer the proposal of modification for two models in order to decrease the drag force. The shape of curvaceous model is better for the pressure force but slightly worse for the viscous force than the other. The Fluent software is used for the calculation of flow profile in this study.

• Journal of computational fluids engineering
• /
• v.18 no.3
• /
• pp.8-13
• /
• 2013

Drag reduction of a running vehicle is very important issue for the energy savings and emission reduction of its power train. Especially for a solar powered electric vehicle, the drag reduction and weight lightening are two serious problems to be solved to extend its driving distance under the given energy condition. In this study, the ground effect of an airfoil shaped road vehicle was studied for an optimum body design of an ultra-light solar powered electric vehicle. Clark-Y airfoil type was adopted to the body shape of the model vehicle to reduce aerodynamic drag. From the study, it was found that the drag of the model vehicle was reduced as the height(h) between ground and the lower surface of the model vehicle was decreased. It is due to the reduction of the down-wash decreasing the induced drag of the vehicle. The lift was also decreased as the height decreased. It is due to the turbulent boundary layer developed beneath the vehicle body. The drag is classified into two types; the form and friction drag. The fraction of form drag to friction one is 76 to 24 on the model vehicle. As the height(h) of the model vehicle from the ground surface increases the form drag also increases but the friction drag is in reverse.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.656-665
• /
• 2021

In this study, trim tabs were attached to end of stern hull of a small high-speed vessel of length approximately 10 m and Froude number 1.0 to improve resistance performance and passenger comfort. Before computational fluid dynamics (CFD) simulations to assess the performance according to various geometries of the trim tab, the scale effect had been found through a previous study, so full-scale simulations were performed. The trim tab chord length was set to 0.5 %, 1.0 % and 1.5 % of L_PP, and its angle to base line was varied in intervals of 5°. It decreased trim by stern and flotation: the greater the angle and length, the greater was the effect. Then it had pressure resistance decreased and shear resistance increased, and reduction ratio of total resistance varied accordingly. The results of this study indicated that the resistance performance was improved about 27 % at optimal running attitude that was the trim by stern about 1.5°.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1694-1695
• /
• 2011

최근 에너지에 대한 관심의 증대 및 센서 노드로의 개발을 위해 무전원 동력 장치(sustainable energy conversion system)에 대한 관심이 크게 증대되고 있다. 본 연구에서는 수압(hydraulic pressure)을 이용하여 전기를 발생시키는 새로운 개념의 나노유체 에너지 변환 시스템에 대한 연구를 진행하였다. 표면 패터닝 기법을 통해 제작된 나노 채널 및 일차원 마이크로 유체 기반의 플루이딕 소자를 이용하여 외부저항, 버퍼용액의 농도, 압력에 따른 streaming potential을 구하였다. electrokinetic 현상과 이에 따른 유체의 streaming potential을 이용하여 압력(pressure)을 전기적으로 변환시키는 에너지 변환용 나노 유체시스템을 본 논문을 통해 제안하고자 한다.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.135-144
• /
• 2009

In this study, the heat transfer and fluid flow characteristics of a condenser for a refrigerator are analyzed with the numerical method. The main objective of the study is to obtain basic data in order to develop a new type of condenser focused on an influence of thermal resistance of air side and thermal contact resistance on the heat transfer performance. The CFD technique was used for whole study, and experiments were performed in order to verify the reliability of the numerical analysis and predict the thermal contact resistance. In this study, a heat exchanger sample was made of a part of condenser to make the experimental and numerical analysis simple and efficient. Water was used for the inner working fluid of the heat exchanger, and an experimental apparatus was composed concisely. A heat exchanger sample of tube type was used to verify the reliability of numerical analysis, and a heat exchanger of fin and tube type was used to predict the ratio of thermal contact resistance to the overall thermal resistance.

• Journal of computational fluids engineering
• /
• v.15 no.1
• /
• pp.81-87
• /
• 2010

In this study, we conducted resistance and propulsion performance test of ship composed of the Resistance Test, Propeller Open Water Test and Self Propulsion Test using the CFD(Computational Fluid Dynamics). We used commercial RANS(Reynolds Averaged Navier Stokes equation) solver, as a calculating tool. The unstructured grids were used in a bow and stern of ship, having complex shape, for a convenience of generating grids, and the structured grids were adopted in a central hull and rest of hull having a relatively simple shape which is called hybrid grid method. In addition, The sliding mesh method was adopted to rotate a propeller directly in the Propeller Open Water and Self Propulsion Test. The Resistance Test and Self Propulsion Test were calculated using Volume of Fluid (VOF) model and considering a free surface. And all The three cases were applied realizable k-epsilon model as the turbulence model. The results of calculations were verified for the suitability of calculations by comparing MOERI's EFD results.