• Transactions of The Korea Fluid Power Systems Society
• /
• v.6 no.1
• /
• pp.10-16
• /
• 2009

Automatic power transmission systems consisted of a torque converter and several planetary gear sets, clutches and brakes are controlled by a hydraulic shift control circuit and an electronic transmission control unit. The hydraulic circuit serves for the operation of the torque converter and lubrication oil supply of the transmission system as well as for the actuation of clutches for the automatic gear shift. The complicated hydraulic control circuit constructed by many spools, solenoids, orifices and flow passages are integrated into one small valve block and it is powered by one hydraulic pump. In this paper, a test equipment was developed to measure the oil consumption of each component at various wide operating conditions. Test data about 730 sets acquired from five test items are analyzed and discussed on the oil capacity of the circuit.

• Journal of Biosystems Engineering
• /
• v.28 no.3
• /
• pp.187-198
• /
• 2003

This study was conducted to investigate the effect of design parameters of modulating valve and hydraulic clutch on the shift quality of a power shuttle transmission using a computer simulation. Computer simulation models of a hydraulic control system and a power shuttle drive train were developed and verified by an experimental power train in a laboratory. The software EASY5 was used for the modeling and simulation of the power shuttle transmission. Results of the study were summarized as follows: For a good shift quality. it is required to reduce the transient torque transmitted to the output shaft of the transmission as much as possible. This may be achieved by reducing the modulating time and clutch pressure. It was found that the design parameters most significantly affecting the modulating time and clutch pressure were the spring constant and displacement of a load piston of the modulating valve, and the spring constant and damping of the clutch piston. The modulating time decreased as the spring constant increased and increased as the displacement of the load piston decreased. The transient torque decreased as the modulating time increased. However their relationships were not always linear. As the damping decreased, both the modulating pressure and time decreased, which also resulted in a decrease in the transient torque. The spring constant of the clutch piston affected the modulating time and the peak transient torque. As the spring constant of the clutch increased, the peak transient torque decreased.

• Journal of Korean Society of Forest Science
• /
• v.97 no.1
• /
• pp.61-70
• /
• 2008

This study was conducted to develop a mobile tower-yarder with tractor for agriculture and forestry that is the efficient yarder in steep terrains, thinning operation and small scale logging operation. It was designed and manufactured that the power source of tower-yarder is equiped three hydraulic pump connected to PTO of tractor, and three hydraulic pump is used to operate the four motor for drum, the cylinder for clutch of interlocker, the cylinder for tower expanding and the out-rigger cylinder. It was to adopt the running skyline system and the inter-lock function, and to equip the double capstan drum, the storage drum and the clutch for interlock in the development of tower-yarder. It was to develop the tower-yarder which the winch torque of double-capstan drum, the traction force of double-capstan drum, the number of rotation of double-capstan drum and the line speed is $191kg{\cdot}m$, 1,910 kgf, 220.5 rpm and 138.5 m/min, respectively. And it was known that the optimum flange diameter of the main and haulback storage drum is about 360 mm and about 460 mm in order to storage the main line length of 250m and the haulback line length of 450 m. The carriage was made to adopt the running skyline system and to equip the lock function in order to the convenience of chocking and the fall down preventing of tree. It was provided to develop the wire remote controller for the inter-lock function, the convenience of control and the efficiency of yarding. In development process, this tower-yarder was attached the 3-point linkage hitch equipment and the tire wheel for the traction and moving of tower-yarder. Also, it was equipped that the out-rigger and the guy line in order to raise the safety and efficiency of yarding of tower-yarder.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.78-78
• /
• 2017

현재 국내에 공급되고 있는 잡곡류 수확기는 보행형 예취기, 탈곡기 위주의 저능률 기계화 수준으로 고능률의 콤바인 수확기 개발이 필요하며, 특히 잡곡류가 소규모 경작지의 영세농가 위주로 재배되어 저가격의 소형 콤바인 수확기 개발이 절실히 요구되고 있다. 따라서 본 연구는 소규모 밭의 두류 및 잡곡 수확작업에 적응성이 뛰어나며, 농기계 임대사업소의 활용도를 높일 수 있고, 여성과 고령자도 쉽게 운전할 수 있어 수확작업의 노동력을 크게 절감할 수 있는 저가격의 25kW급 자주식 소형 콤바인을 개발하고자 시작기를 설계 제작하였다. 시작기의 주요부로 엔진은 25kW/2600rpm 3기통 디젤엔진을 탑재하였으며, 동력전달부는 주변속 3단, 부변속 2단의 선택맞물림 기어식의 변속장치를 이용하였다. 주행부는 궤도형으로 조향클러치와 습식 원판식 제동장치를 채용하였다. 전처리부는 선단거리 1700 mm의 디바이더와 상하좌우 수동 조절되는 회전속도 약 42 rpm의 정오각형 릴로 구성하였으며, 전처리부의 최대 승강높이는 740 mm이었다. 작물이송부는 돌기부착 오거와 체인컨베이어로 구성되어 있으며, 탈곡부는 단동형 축류식의 직경 440 mm, 길이 1180 mm의 급동과 높이 65 mm, 지름 10 mm의 46개 강봉형 급치, 격자형 수망으로 구성하였으며, 회전속도는 약 325 rpm으로 작동하도록 하였다. 선별 정선부는 요동 송풍선별식으로 곡립판, 볏짚체, 곡립체, 송풍팬으로 구성하였고 송풍팬의 회전속도는 약 850 rpm, 요동진동수는 약 5.8 Hz로 작동하도록 하였다. 곡물이송부와 재처리부는 수평이송 외경 103 mm, 수직이송 외경 110 mm의 피치가 모두 82 mm인 스크류컨베이어를 이용하였으며, 곡물탱크는 용량이 250 로 2개의 배출구로 곡물을 포대에 담도록 하였다. 그 외 시작기는 운전조작부, 유압장치부, 전기장치부 등을 갖도록 설계 제작하였다. 전체적인 기체의 크기는 길이${\times}$폭${\times}$높이 $3935{\times}1900{\times}2440mm$이었으며, 기체 중량은 약 1753 kg이었다. 콩 대상 기초 성능시험 결과 시작기의 작업속도는 약 0.5 m/s, 작업능률은 약 11 a/h로 나타났다.