• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.721-727
• /
• 2002

In order to overcome trade-off among compositions, process and properties of the glasses with high PbO-base composition for PDP Rib, we studied glass crystallization and crystallization kinetics by Differential Thermal Analysis(DTA). Glass powder was obtained through melting/cooling/grinding, with 3 wt%TiO2 addition for the crystal nucleation and growth in $62PbO-19B_2O_3-10SiO_2-9(Al_2O_3-K_2O-BaO-ZnO)$(in wt%) composition glass. This powder was heat-treated for 1 to 10 h at $445^{\circ}C$ for nucleation. DTA measurements were performed to obtain the crystallization peak with $5∼25^{\circ}C/min$ heating rates. DTA crystallization peak temperature increased with increasing the heating rate and decreased with increasing the heating time. Because the Avrami parameter (n) was approximately 1, the surface crystallization occurred. The maximum nucleation time was 2 h.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.272-277
• /
• 2019

In this paper, a manufacturing method of an anti-glare cover glass on LCD for outdoor use is proposed. The main specification of cover glass is hardness and anti-glare. Hardness is achieved by using the tempered glass, and anti-glare(AG) film is laminated to meet anti-glare specification no the tempered glass. However, the AG film is difficult to maintain the AG performance continuously because the abrasion resistance of the PET film itself is as weak as about 3H. Therefore, a novel production procedure using screen printing method is proposed. The proposed coating is implemented by applying $ZnO-B_2O_3-SiO_2$ powder on glass surface and the glass is made with enhanced hardness through tempering process. In order to apply the ZBS powder uniformly on the glass surface, a screen printing process is used. The main parameters to be considered in screen printing are the oil concentration and mesh opening size. Because the amount of ZBS powder applied to the printing process is controlled by these two parameters, the correlativity is confirmed through the experiments. In order to evaluate the performance of the proposed method, the haze, surface roughness and transmittance are selected as the performance index and are compared with the AG film. As a result of comparison, it is verified that the transmittance of the proposed tempered glass is 83.1%, which is slightly lower than 89.5% of AG film, but the hardness is more than double to 7H.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.337-337
• /
• 2009

가시광선영역에서 매우 균일한 높은 투과성뿐만 아니라 근적외선영역에서 가파른 홉수성 엣지와 함께 낮은 투과율을 제공하는 산화구리(II)를 함유하는 포스페이트 유리는 컬러 비디오 카메라의 컬러 보정 필터, 발광 컬러 디스플레이용 보호판(sheild), 모노크로메이터의 미광 필터, 플라스틱 복합재 필터의 무기 성분 및 CCD(전하 결합 소자) 및 CMOS(상보성 금속 산화물 반도체) 카메라 및 검출기 분야용 필터 유리로서 사용된다. 용융온도 및 산화구리(II) 첨가량에 따른 투과율을 측정하기 위해 포스페이트 유리 시료를 $1100\sim1500^{\circ}C$ 용융한 후 $400^{\circ}C$에서 2시간 동안 어닐링 공정을 거쳐 제조하였다. 제조된 시료는 두께 0.3mm로 폴리싱하여 자외선-적외선 분광 광도기를 이용하여 광학적 특성을 측정하였다. 본 실험을 통하여 용융온도에 따라 가시광선영역 및 근적외선영역에서의 투과율 거동을 비교한 결과 $1100\sim1200^{\circ}C$에서의 우수한 투과율 특성을 나타냈다. 용융온도가 내려감에 따른 가시광선영역 (400~600nm)에서 높은 투과율 및 근적외선영역 (750~1100nm)에서 낮은 투과율과 가파른 흡수성 엣지를 나타냈다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.71-71
• /
• 2003

최근 통신용 전자부품의 소형화, 저가격화, 고기능화의 요구가 점점 더 증대되고 있으며 이를 위해서 기판의 배선밀도를 높이는 것과 개별 부품 또는 모듈의 크기와 무게를 줄이는 것이 절실히 필요하다. 본 연구에서는 저융점의 phosphate계 유리 프릿의 첨가를 통해 LTCC (Low Temperature Co-fired Ceramic) 에 적용 가능한 조성을 개발하고자 하였다. 마이크로파 용 유전재료로서 널리 사용되고있는 BNT (BaO-Nd$_2$O$_3$-TiO$_3$) 계 세라믹스에 저융점 유리 프릿의 양을 10-30wt% 범위로 변화시키면서 900-110$0^{\circ}C$ 범위에서 소결하여 이에 따른 수축률 변화와 상대밀도의 변화를 조사하였다 유리 프릿으로 P$_2$O$_{5}$-ZnO-BaO-Nd$_2$O$_3$ 계, P$_2$O$_{5}$-SnO-ZnO 계 2가지 조성의 유리를 사용하였다 그 결과로 소결체의 상대밀도는 소성온도가 900-110$0^{\circ}C$ 로 증가함에 따라 85-96% 로 증가하였고, 그 수축률은 소결온도 100$0^{\circ}C$ 에서 급격히 증가하였다. 이러한 결과는 저온 동시소성 세라믹 조성의 사용을 위해 좋은 결과가 예상된다.

• The Journal of Engineering Research
• /
• v.3 no.1
• /
• pp.199-205
• /
• 1998

Cullet Quality Control in auto glass bottle factory is the most important in recent days because of the increasing cost of materials in glass bottle. Since the composition of plate glass cullet is similar, the cullet quality using plate cullet in glass bottle factory is easily controlled. In addition to this, the price of plate glass cullet is so low that the cost reduction can be achieved. If the ratio of plate glass cullet and gush is over 25%, the liquidity of glass water become worse, which is caused by different compositions and viscosity of the components. As a results, Furnace bottom temperature becomes low and glass water becomes inhomogeneous. Thus production efficiency of glass bottle becomes low because of increasing devitrification in Dead Corner part in glass melting furnace. Three experimental methods – (1) increasing melting temperature, (2) using Booster, (3) using bubbler – were performed to increase the furnace bottom temperature and glass water homogeneity. The amounts of plate glass cullet was able to increase up to 90%, 70% and 60% without any devitrification using booster, bubbler and the method of glass melting temperature increase from $1480^{\circ}C$ to $1560^{\circ}C$ respectively. It is not possible to increase the glass melting temperature without the reduction of furnace operation time and the increase of fuel cost. The booster process has disadvantage of much electric energy consumption. Since the bubbler process uses physical convection of melting glass based on compression air, the homogeneity of molten glass is not so good as that of booster process but it can reduce the cost of glass bottle.

• Applied Chemistry for Engineering
• /
• v.2 no.3
• /
• pp.289-299
• /
• 1991

In order to obtain glasses appropriate to the thick film copper conductors, nine glasses based on both lead borosilicate and leadless borosilicate systems were made and the applicabilities of them were examined in conjunction with the requirements for thick film copper conductors. As the results, it was found that all the glasses are fitted to provide suitable sheet resistance, solderability and solder leach resistance to thick film copper conductors. However, it was turned out that only the lead borosilicate based glasses worked for getting usable aged adhesion strength of copper thick film to the alumina substrate, while copper conductor films made from the other glasses had poor aged adhesion strengths. Particularly cuprous oxide added lead borosilicate glass was considered as one of the most favorable glasses for manufacturing thick film copper conductors.

• Journal of the Korean Ceramic Society
• /
• v.41 no.12 s.271
• /
• pp.939-945
• /
• 2004

Glasses of $SiO_2-B_{2}O_3-Al_{2}O_3-CaO-La_{2}O_3$ with various amounts of $La_{2}O_3$ were infiltrated into a porous alumina to make an alumina-glass composite. The infiltration characterization and bending strength of the composite were examined in terms of glass composition. $La_{2}O_3$ in the glass decreased the high temperature viscosity and this enhanced the wetting behaviour of this glass to alumina, and made glass infiltration easier. The infiltrated glass dissolved the alumina skeleton, and $Al_{2}O_3$ component in the glass melt reprecipitated on the alumina. The grain growth occurred to a specific crystal direction. The glass containing $20mole\%$ of $La_{2}O_3$ was crystallized after infiltration, and this enhanced the bending strength of the composite.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.167-167
• /
• 2010

Ge-Sb-Se계 칼코게나이드 유리의 Melting 조건변화에 따른 특성변화를 연구하였다. Glass melting 조건(homogenization-temperature, homogenization-time, annealing) 에 따라 제작된 칼코게나이드 유리 bulk를 FT-IR, XRD, SEM 등의 분석장비를 이용하여 특성을 분석하였다. Homogenization temperature가 높을수록 석영관 급냉 시 발생되는 mechanical stress와 내부응력차로 인해 칼코게나이드 유리 깨짐현상이 증가하였으며 조성비와 melting 조건에 따라 XRD분석에서 확인되지 않는 미소결정이 SEM 분석결과 관찰되었다. 본 연구를 통해 칼코게나이드 유리의 melting 조건에 따른 경향성을 확인할 수 있었다.

• Proceedings of the KAIS Fall Conference
• /
• 2005.05a
• /
• pp.89-92
• /
• 2005

본 연구에서는 미량원소 함유 $K_2O-CaO-P_2O_5$유리를 제조하였으며, 화학비료와의 혼합을 통하여 얻어진 유리질 비료를 사용하여 작물배지 적합성 및 친환경성을 평가하였다. 용출특성의 경우 유리조성변화를 통하여 장기 및 단기용출이 가능하였으며, 벼에 적응한 결과 생육, 수량은 대조구와 유사하였으며, 식미치의 경우 보다 우수하였다. 또한, 용탈수 분석으로부터 환경친화적 유리질 비료로서의 가능성을 보였다.

• Journal of the Korean Ceramic Society
• /
• v.37 no.9
• /
• pp.879-886
• /
• 2000

고온용 전기.열 절연재의 유리모재로 사용하기 위한 산화크롬함유 인산염 유리 복합체의 소결거동, 물성, 그리고 미세구조변화를 연구하였다. 단미의 유리는 점성유동에 의한 1단계 소결수축을 보이나 복합체는 점성유동 및 반응 액상소결에 의한 2단계 수축을 보였다. 단미 유리는 소결온도 증가에 따라 재기공율이 감소하고 기공크기가 작아지지만 93$0^{\circ}C$ 이사에서는 폐기공이 생성되면서 기공이 성장함을 보였다. 복합체 소결밀도는 산화크롬 증가에 따라 감소하였으며, 특히 산화크롬 40% 이상에서는 percolation에 의해 소결수축율이 급격히 저하하였다. 복합체의 곡강도는 산화크롬 증가에 따라 거의 직선적으로 감소한 반면 열팽창율은 오히려 급속히 증가함을 보였다.