• The Korean Journal of Rheology
• /
• v.10 no.4
• /
• pp.185-194
• /
• 1998

Flow-induced voids during resin impregnation and poor fiber wetting give serious effects on the mechanical properties of composites in resin transfer molding process. In order to better understand the characteristics of resin flow and to investigate the mechanism of void formation, flow visualization experiment for the resin impregnation was carried out on plain weaving glass fiber mats using silicon oils with various viscosity values. The permeability and the capillary pressure for the fiber mats of different porosities were obtained by measuring the penetration length of the resin with time and with various injection pressure. At low porosity and low operating pressure, the capillary pressure played a significant role in impregnation process. Video-assisted microscopy was used in taking the magnified photograph of the flow front of the resin to investigate the effect of the capillary pressure on the void formation. The results showed that the voids were formed easily when the capillary pressure was relatively high. No voids were detected above the critical capillary number of 2.75$\times$$10^{-3}, and below the critical number the void content increased exponentially with decrease of the capillary number. The content of void formed was independent of the viscosity of the resin. For a given capillary number, the void content reduced with the lower porosity of the fiber mat.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.7
• /
• pp.435-443
• /
• 2017

The Characteristics of the flowfields of a square prism having a small square prism were investigated by measuring of lift and drag on the square prism and visualizing the flowfield using PIV. The experimental parameters were the width ratios(H/B=0.2~0.6) of small square prisms to the prism width and the gap ratios (G/B=0~3) between the prism and the small square prism. The drag reduction rate of the square prism initially increased and then decreased with the G/B ratio for the same H/B ratio, and increased with the H/B ratio for the same G/B ratio. The maximum drag reduction rate of 98.0% was observed at H/B=0.6 and G/B=1.0. The lift reduction rate of the square prism was not affected by the width and gap ratios; the total average value was approximately 66.5%. In case of a square prism having a small square prism, the stagnation regions were represented in the upstream and downstream sides of the square prism.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.6
• /
• pp.373-381
• /
• 2016

In this study, we investigate the characteristics of the drag reduction of a circular cylinder having a detached splitter plate at the wake side. We measure the fluid force on a circular cylinder and visualize the field using particle image velocimetry (PIV) with a high Reynolds number, Re = 10,000. The experimental paraeters used were the width ratios (H/B = 0.5~1.5) of splitters to the prism width and the gap ratios (G/B = 0~2) between the prism and the splitter plate. The drag-reduction rate of the circular cylinder increased with H/B in the case of the same G/B, and it increased and then decreased with G/B in the case of the same H/B. The vortices of the opposite direction on the upper and lower sides of the detached splitter plate were generated by installing the plate. Reverse flow was caused by the vortices at the wake region of the circular cylinder, and the drag of the circular cylinder was decreased by the reverse flow.

• Clean Technology
• /
• v.13 no.2
• /
• pp.151-158
• /
• 2007

An experimental study to investigate the condensing heat transfer characteristics of small diameter horizontal double pipe heat exchangers with R-22 and R-410A was performed. Experimental facility was constructed to calculate and observe HTC(heat transfer coefficients), flow patterns and pressure drop. The main components include a liquid pump, an evaporator, a condenser(test section), a sight-glass, pressure taps and measurement apparatus. Two pipes of different diameters are tested; One 5.35 mm ID 0.5 mm thick, the other 3.36 mm ID 0.7 mm thick. The mass flow rate ranged from 200 to $500\;ks/m^2{\cdot}s$ and heating capacity were form 1.0 to 2.4 kW. The flow patterns of R-22 and R-410A were observed with a high speed camera through the sight-glass. The tests revealed that HTC of R-410A was higher than that of R-22 by maximum 5%. Annular pattern was observed for the most cases but stratified flow was also detected when x<0.2. The pressure drop in 3.36 mm ID pipe was higher than that of 5.35 mm by $30{\sim}50%$. Comparing with previous correlations such as Shah, Fujii and Soliman's, Fujii' showed the best good agreement with my data with a maximum deviation of 40%.

• Journal of the Korean Institute of Gas
• /
• v.2 no.1
• /
• pp.28-39
• /
• 1998

This study investigated the natural convection and radiation in a rectangular enclosure with ceiling vent experimentally and numerically. A heat source is located on the center of the bottom surface. The analysis was peformed a pure convection and is combination of natural convection and radiation. The shape of the considered two dimensional model is a square whose center of ceiling($30\%$) is opened. The numerical simulations are carried out for the pure natural convection case and the combined heat transfer case by using the SIMPLE algorithm. For the turbulent flow, Reynolds stresses are closed by the standard $k-{\epsilon}$ model and the wall function is used to determine the wall boundary conditions. The experiment was performed on the same geometrical shape as the computations. The radiative heat transfer is analized by the S-N discrete ordinates method. The results of pure natural convection are compared with those of combined heat transfer by the velocity vectors, stream lines, isothermal lines. The results obtained are as follows 1. Comparing the results of pure convection with those of the combined convection-radiation through the shape of stream lines, isothermal lines are similar to each other. 2. The temperature fields obtained by numerical method are compared to those obtained by experimental one, and it is found that they are showed mean relative error $8.5\%$. 3. Visualization bt smoke is similar to computational results.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.14 no.4
• /
• pp.128-136
• /
• 2011

To monitor and predict the change of coastal environment according to the construction of Saemangeum sea dyke and the development of land reclamation, we have done real-time and periodic ocean observation and numerical simulation since 2002. Saemangeum coastal environmental data can be largely classified to marine meteorology, ocean physics and circulation, water quality, marine geology and marine ecosystem and each part of data has been generated continuously and accumulated over about 10 years. The collected coastal environmental data are huge amounts of heterogeneous dataset and have some characteristics of multi-dimension, multivariate and spatio-temporal distribution. Thus the implementation of information system possible to data collection, processing, management and service is necessary. In this study, through the implementation of Saemangeum coastal environmental information system using geographic information system, it enables the integral data collection and management and the data querying and analysis of enormous and high-complexity data through the design of intuitive and effective web user interface and scientific data visualization using statistical graphs and thematic cartography. Furthermore, through the quantitative analysis of trend changed over long-term by the geo-spatial analysis with geo- processing, it's being used as a tool for provide a scientific basis for sustainable development and decision support in Saemangeum coast. Moreover, for the effective web-based information service, multi-level map cache, multi-layer architecture and geospatial database were implemented together.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.8
• /
• pp.531-536
• /
• 2017

Nano/micro technology is currently applied to improve solid surface wettability, with recent research studies indicating that nanostructures can improve surface wettability in the hydrophilic direction, and liquid spreading (propagation) is generated by capillary wicking. The majority of the existing research involves qualitative analysis of the spreading phenomena, owing to the difficulty in conducting small-scale analysis (nanostructures). In this study, the droplet interfacial behavior on silicon surfaces with micro/nano/micro-nano structures is experimentally investigated. The interfacial behavior is directly visualized using synchrotron X-ray imaging (side view). The spreading phenomena occur on structured surfaces, and the liquid interface behaviors on the surfaces differ. The liquid film thickness is uniform during spreading on the microstructured surface, but not on the nano case which shows a gentle slope. These combined spreading shapes were observed on a micro-nano structured surface, and liquid propagation was enhanced when the micro- and nano-structures are combined.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.10
• /
• pp.118-126
• /
• 2004

The propulsive characteristics of oscillating flat plates are investigated using a discrete vortex method. The plates and their wakes are represented by discrete point vortices. To analyze the closely coupled aerodynamic interference between the plates, a vortex core model and a vortex core addition scheme are combined. A calculated wake shape for a flat plate in heaving oscillation is compared with flow visualization. The effect of wake shapes on the propulsive characteristics of the plates in pitching oscillation is investigated. The propulsive characteristics of oscillating plates with three cases (1. one is stationary and another is oscillating, 2. both oscillating in phase, 3. both oscillating out of phase) are calculated. The plates oscillating out of phase showed the largest thrust force among the three cases.

• 한국공간정보시스템학회:학술대회논문집
• /
• 2005.05a
• /
• pp.165-174
• /
• 2005

고압전류가 흐르는 송전탑이 주거 밀집지역 인근에 설치되거나 송전탑과 가까운 곳에 아파트가 건설되면서 주민들이 한전을 상대로 손해배상 청구소송을 추진하는 등 전자파 피해에 따른 민원이 끊이지 않고 있다. 이와 같은 문제에 대해 해결책을 제시하기 위해서는 송전선 주변 전자파의 실체에 대해 과학적이고 객관적인 조사를 거쳐 국민에게 납득할 수 있는 대안을 제시하는 것이 선행되어야할 작업이다. 그러나 현재 전자파 데이터는 조사 지점만의 단편적인 측정치를 보여주는 수준에 머물러 있어 전자파 확산 등 광역적인 분포 추이에 대한 시각적인 정보를 입수하는 데 상당한 한계가 있다. 따라서 본 연구에서는 GIS기반의 공간 모델링 기법을 활용하여 거리와 전류를 토대로 분포되는 송전선 주변의 전자파 시뮬레이션 기법을 제안하고자 한다. 이와 같은 문제에 대해 대안을 제시하고자, 지역주민이 일상생활에서 접하고 있는 지역의 지도(건물, 도로망 등)를 전자파 유동에 관한 이론에 의거하여 3차원 상에서 전자파 시뮬레이션을 수행하였다. 전자파 시뮬레이션 결과를 검증하기 위해 사용한 실측 데이터는 인천광역시 서구 가정2동에 위치한 봉수 초등학교의 학생들에게 전자파 측정장비를 부착하도록 하여 확보하였다 송전선에서 전자파 방출에 개입하는 거리와 전류의 세기에 의거하여 전자파의 분포를 예측하였으며 실측 데이터와 이론적인 데이터를 비교하여 상관성을 평가했다. 통상 전자파 조사과정은 지도에 표기된 조사지점을 일일이 확인하는 등 모든 측정 작업을 수작업에 의존하고 있다. 따라서 DB구축에 시간이 많이 소요되고 정확도도 많이 떨어질 수밖에 없어 다양한 조건으로 방대한 자료를 공간상에서 검색하는 것 자체가 불가능하였다. 전자파의 분포를 그래픽정보로 가공하여 광역적인 전자파 변화 추이를 풍부한 시각 정보로 디스플레이 하는 것도 어려웠다. 또한 수작업으로 인한 실수도 많이 발생하고 그에 따른 교정 작업도 복잡하였다. 본 연구에서는 송전선에서 방출되어지는 전자파의 이론적인 데이터와 실측 데이터의 상관성에 따른 분석 결과를 가지고 실측 데이터 없이 GIS 기반의 3D 시뮬레이션에 의거하여 전자파의 공간적인 가시화를 수행할 수 있었다. 본 전자파 시뮬레이션 기법이 실무에 이용될 경우, 일반인이 전자파의 분포에 대한 전문지식을 습득할 필요 없이, 검색하고자 하는 지역과 송전선, 전철 등 각종 전자파의 발생 공간 객체를 선택하여 실생활과 관련된 전자파 정보에 예측할 수 있어, 대민 환경정보 서비스 질의 개선측면에서 획기적인 계기를 마련할 것으로 사료된다.

• Korean Journal of Construction Engineering and Management
• /
• v.5 no.6 s.22
• /
• pp.218-225
• /
• 2004

The supply for the apartment complex in Korea has been accomplished by the sale before building system as a way of institutional means to support massive housing supply in the past. Although this sale before building system has helped the provision of the housing, the necessity of that has been weakened in the current housing market. As this market is changed to emphasize on consumer, the necessity of conversion to sale after building system was raised and finally enforced partially. However, the sale after building system has difficulty in ensuring construction fund and the safety of housing business. So, the diversification in the style of business structure we and the strategy for the activation of construction fund will solve these problems. Consequently, this essay examine the change and influence in the construction fund after adopting sale after building system and suggest the appropriate strategy in project financing for providing fund and reducing the risk in construction business.