• Journal of Bio-Environment Control
• /
• v.25 no.3
• /
• pp.218-223
• /
• 2016

The calculation method of ground heat exchange in greenhouses has different ideas in each design standard, so there is a big difference in each method according to the size of greenhouses, it is necessary to establish a more accurate method that can be applied to the domestic. In order to provide basic data for the formulation of the calculation method of greenhouse heating load, we measured the soil temperature distribution and the soil heat flux in three plastic greenhouses of different size and location during the heating period. And then the calculation methods of ground heat exchange in greenhouses were reviewed. The soil temperature distributions measured in the heating greenhouse were compared with the indoor air temperature, the results showed that soil temperatures were higher than room temperature in the central part of greenhouse, and soil temperatures were lower than room temperature in the side edge of greenhouse. Therefore, it is determined that the ground heat gain in the central part of greenhouse and the perimeter heat loss in the side edge of greenhouse are occurred, there is a difference depending on the size of greenhouse. Introducing the concept of heat loss through the perimeter of building and modified to reflect the size of greenhouse, the calculation method of ground heat exchange in greenhouses is considered appropriate. It was confirmed that the floor heat loss measured by using soil heat flux sensors increased linearly in proportion to the temperature difference between indoor and outdoor. We derived the reference temperature difference which change the direction of ground heat flow and the perimeter heat loss factor from the measured heat flux results. In the heating design of domestic greenhouses, reference temperature differences are proposed to apply $12.5{\sim}15^{\circ}C$ in small greenhouses and around $10^{\circ}C$ in large greenhouses. Perimeter heat loss factors are proposed to apply $2.5{\sim}5.0W{\cdot}m^{-1}{\cdot}K^{-1}$ in small greenhouses and $7.5{\sim}10W{\cdot}m^{-1}{\cdot}K^{-1}$ in large greenhouses as design standard data.

• Progress in Medical Physics
• /
• v.17 no.1
• /
• pp.47-53
• /
• 2006

The accuracy of the dosimetry in the Cyberknife system is accomplishing important role from all processes of the stereotactic radiosurgery. In this study, we estimated relative output factors for Cyberknife. All measurements were peformed by six different detectors: diode detector, X-Omat V film, Gafchromic EBT film, 0.015 cc, 0.125 cc and 0.6 cc ionization chamber The diode detector and three ionization chambers peformed using water phantom at 80 cm SSD and 1.5 cm depth. When the film measurements were peformed, the water phantom was replaced with a solidwater phantom. Each collimator normalized with respect to the output factor of the largest collimator (60 mm). For the collimators over than 30 mm, the output factors from the different detectors showed a good agreement within 0.5% except 0.6 cc ion chamber For the collimators less than 15 mm, there were substantial differences In the output factors among different detectors. That is, the value of output factor for the 5 mm collimator of a diode and Gafchromic film was each $0.656{\pm}0.009$ and $0.777{\pm}0.013$. In the ion chamber and diode detector, those difference were due to the presence of large dose gradients and lack of electronic equilibrium in narrow megavoltage x-ray beams Therefore, the Gafchromic EBT film were considered more accurate than the others detectors.

• Progress in Medical Physics
• /
• v.24 no.4
• /
• pp.237-242
• /
• 2013

In the intracranial regions, an accurate delineation of the target volume has been difficult with only the CT data due to poor soft tissue contrast of CT images. Therefore, the magnetic resonance images (MRI) for the delineation of the target volumes were widely used. To calculate dose distributions with MRI-based RTP, the electron density (ED) mapping concept from the diagnostic CT images and the pseudo CT concept from the MRI were introduced. In this study, the look up table (LUT) from the fifteen patients' diagnostic brain MRI images was created to verify the feasibility of MRI-based RTP. The dose distributions from the MRI-based calculations were compared to the original CT-based calculation. One MRI set has ED information from LUT (lMRI). Another set was generated with voxel values assigned with a homogeneous density of water (wMRI). A simple plan with a single anterior 6MV one portal was applied to the CT, lMRI, and wMRI. Depending on the patient's target geometry for the 3D conformal plan, 6MV photon beams and from two to five gantry portals were used. The differences of the dose distribution and DVH between the lMRI based and CT-based plan were smaller than the wMRI-based plan. The dose difference of wMRI vs. lMRI was measured as 91 cGy vs. 57 cGy at maximum dose, 74 cGt vs. 42 cGy at mean dose, and 94 cGy vs. 53 at minimum dose. The differences of maximum dose, minimum dose, and mean dose of the wMRI-based plan were lower than the lMRI-based plan, because the air cavity was not calculated in the wMRI-based plan. These results prove the feasibility of the lMRI-based planning for brain tumor radiation therapy.

• Geophysics and Geophysical Exploration
• /
• v.13 no.4
• /
• pp.357-363
• /
• 2010

In this study, we investigated the geologic structure of the basement and overlying sediments of the construction site of the dinosaur egg fossil museum in Hwasung, Gyeonggi Province through refraction seismology, drilling, and downward seismic velocity measurements in the drill holes. The construction site ($350{\times}750\;m^2$) is located in the reclaimed area south of Sihwa Lake, Gojeong-ri. About 6,950 m of seismic refraction data consisting of 11 lines were acquired using a sledge hammer source. Drilling to the basement was performed at five sites. Sediment samples from drilling were analysed for grain-size distribution and age dating. At two drill holes, seismic velocity was measured with depth using a hammer as a seismic source. The geological structure of the study area consists of, from top to bottom, a tidal flat layer (5 ~ 12 m thick), a weathered soil layer (2 ~ 8 m thick), and the basement. The basement is interpreted as Cretaceous sedimentary rocks that tend to be shallow eastward. The volume of the tidal flat sediments and weathered soil in the study area is estimated as $1.4{\times}10^6\;m^3$, weighing $3.5{\times}10^6$ tons. The rate of sea level rise since 8,000 yrs BP is estimated to be 0.1 ~ 0.15 cm/yr.

• Korean Journal of Environment and Ecology
• /
• v.27 no.1
• /
• pp.113-126
• /
• 2013

This study was performed to introduce ecological education program as for reporting the current vegetation state within the remaining trees as ecological golf course and to provide basic data. The survey site was S Golf course, which is located in Woonseodong, Incheon city. Its total area was about $3,298,428m^2$, but the relict forest was about $225,143m^2$. Existing landuse, topological structure, the flora, actual vegetation, and plants community structure survey were performed within the relict forest. As result of comparing and analyzing the existing land use, the relict forest was distributed in the forested areas (89.2%) and around the area (10.8%) which had been bare land and SAMMOK earthen ramparts. There were two courses (Ocean and Hanul) with the relict forests. The ocean course was compared of a natural forest, such as Quercus spp. mixed forest, Quercus acutissima forest, Pinus thunbergii forest within the rock fields, and an artificial forest (Ailanthus altissima-Robinia pseudoacacia forest, Robinia pseudoacacia forest) and Quercus acutissima - Elaeagnus umbellata forest. On the Hanul course, Pinus rigida forest and Robinia pseudoacacia forest were the main vegetation, which were artificial forest. It was the contrast aspect of vegetation species in a natural forest, a restoration forest and an artificial forest, which were Q. spp. mixed forest 26~28 species in a natural forest within the vegetation type per investigation area, 3 Pinus thunbergii forest species, and 5~7 artificial forest species on the Hanul course. Based on these vegetation status, the Ocean course was designed into ecological theme spaces named 'Quercus spp.' indigenous forest, 'Pinus thunbergii' restoration forest and ecological story of 'SAMMOK earthen ramparts'. The Hannul course was designed into an artificial forest observation area of 'Robinia pseudoacacia' and 'Pinus rigida' and a fragrance forest area of 'Robinia pseudoacacia'. At the time of the discussion about the introduction of eco-friendly approval system of golf course, it would be estimated that this survey would work as a major material not only raising awareness of the golf course on the ecological environment but also providing programs that can contribute to the community.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.75-82
• /
• 2019

Flexible solar cells have attracted enormous attention in recent years due to their wide applications such as portable batteries, wearable devices, robotics, drones, and airplanes. In particular, the demands of the flexible silicon and compound semiconductor solar cells with high efficiency and high reliability keep increasing. In this study, we fabricated a flexible InGaP/GaAs double-junction solar module. Then, the effects of the wind speed and ambient temperature on the operating temperature of the solar cell were analyzed with the numerical simulation. The temperature distributions of the solar modules were analyzed for three different wind speeds of 0 m/s, 2.5 m/s, and 5 m/s, and two different ambient temperature conditions of 25℃ and 33℃. The flexibility of the flexible solar module was also evaluated with the bending tests and numerical bending simulation. When the wind speed was 0 m/s at 25 ℃, the maximum temperature of the solar cell was reached to be 149.7℃. When the wind speed was increased to 2.5 m/s, the temperature of the solar cell was reduced to 66.2℃. In case of the wind speed of 5 m/s, the temperature of the solar cell dropped sharply to 48.3℃. Ambient temperature also influenced the operating temperature of the solar cell. When the ambient temperature increased to 33℃ at 2.5 m/s, the temperature of the solar cell slightly increased to 74.2℃ indicating that the most important parameter affecting the temperature of the solar cell was heat dissipation due to wind speed. Since the maximum temperatures of the solar cell are lower than the glass transition temperatures of the materials used, the chances of thermal deformation and degradation of the module will be very low. The flexible solar module can be bent to a bending radius of 7 mm showing relatively good bending capability. Neutral plane analysis was also indicated that the flexibility of the solar module can be further improved by locating the solar cell in the neutral plane.

• Korean Journal of Ichthyology
• /
• v.6 no.2
• /
• pp.132-159
• /
• 1994

The taxonomic revision of the family Congridae was made based on the specimens collected from the south-western coasts of the Korea from June 1988 to Oct. 1993. The family Congridae was classified into 8 species belonging to 6 genera. based on the external and internal morphological characters : Anago anago, Ariosoma anagodies, Ariosoma shiroanago shiroanago, Conger myriaster, Conger japonicus, Gnathophis nystromi nystromi, Rhechias retrotincta and Uroconger lepturus. Among the species reported as the congrid eels from Korea until now, four species were transferred into different generic or specific name Conger flavirostris into Ariosoma anagoides ; Astroconger myriaster into Conger myriaster ; Congrina retrotincta into Rhechias retrotincta and Rhynchocymba nystromi into Gnathophis nystromi nystromi. A Korean congrid eel, Ariosoma shiroanago shiroanago, was reported for first time in Korea. Intergeneric characters of the family Congridae were the form of the lateralline scales, the state of the tip of tail, the segmented state of the dorsal and anal fin rays, the existance of the supraoccipital bone and of lateral ethmoid process of the skull, the origin of dorsal fin and the forms of upper labial flange. The interspecific classification was made according to the characters such as the numbers of sensory pores of head part and in front of vent, teeth rows and numbers of upper and lower jaw, the numbers of vertebrae, the body color, the shapes of the head part, the color of intestine, the size of eye, the structure of air bladder and the number of branchiostegal rays. A new key on the taxonomical characteristics to the genera and species of the family Congridae has been estabilished and their distribution in Korea is described.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.182-190
• /
• 2009

Statement of problem: Microleakage at the occlusal and gingival margin of Class V cavities restored with composite resin has traditionally been considered an obstacle to successful restoration. Purpose: The aim of this study was to assess the effectiveness of three different surface sealants(Fortify, Permaseal and Biscover LV) on the marginal sealing of Class V light-activated composite resin restorations(Z250). Material and methods: Forty noncarious human premolars and molars extracted within a three-month period were selected. Class V cavities with the occlusal margin in enamel and gingival margin in cementum were prepared in both buccal and lingual surfaces. The teeth, randomly assigned in four groups with twenty cavities in each group, were restored with composite resin after applying an adhesive system(Clearfil SE bond). After the finishing and polishing procedures, the restorations were covered with a specific surface sealants, except for the control samples, which were not sealed. After placing restorations, the specimens were thermocycled, and immersed in a 2% methylene blue solution for twenty four hours and sectioned longitudinally. The marginal microleakage was evaluated at the occlusal and gingival interfaces using a microscope and compared among the four groups using ANOVA test and Wilcoxon Rank-Sum test($\alpha$=0.05). Results: Statistical analysis showed that there was significantly less leakage when the surface sealants were used than there was in control group(P<.05). There were no significant differences of microleakage at occlusal and gingival margins among groups. There were no significant differences between microleakage of occlusal and gingival margins in each group. Fortify was not statistically different from control group at the gingival margin(P>.05). Conclusion: Application of surface sealants was an effective method of surface coating in reducing microleakage at occlusal and gingival margins of Class V composite resin restorations. However, it is certain that some microleakage still occurred despite the application of surface sealants, especially gingival margins.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.2
• /
• pp.105-115
• /
• 2008

Statement of problem: Proper finishing and polishing enhance both the esthetics and the longevity of restored teeth. Blade finishing technique would be suited for smoothing and finishing. Evaluation of this technique are necessary. Purpose: The purpose of this study was to evaluate the blade finishing and polishing procedures on the surface profile and roughness of ormocer-based composite resin and nanohybrid composite resin. Material and methods: The material included a ormocer-based composite resin ($Admira^{(R)}$ & $Admira^{(R)}$ Flow); a nanohybrid composite resin ($Grandio^{(R)}$ & $Grandio^{(R)}$ Flow). One hundred forty specimens of each group were prepared using a mylar strip and randomly divied into blade finishing and rubber polishing groups (n=10). The average surface roughness (Ra) in micrometers was measured and the surface profile was examined by scanning electron microscopy (SEM) (Magnification ${\times}$ 200). The data were analyzed by Mann-Whitney Test at 0.05 significance level. Conclusion: The results of this study indicated that the mylar strip produced the smoothest surface on all materials and among the finishing-polishing methods was not significanct difference (P>0.05). Ormocer-based flowable composite resin performedthe lowest variability in initial surface roughness among the tested materials.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.4
• /
• pp.369-381
• /
• 2019

The aim of this study was to analyze the changes and improvements in symptoms of sleep-disordered breathing (SDB) using semi-rapid maxillary expansion (SRME) in children with narrow maxilla and SDB symptoms. Subjects were 15 patients with sleep disorder (apnea-hypopnea index, AHI ≥ 1) and narrow maxillary arch between 7 and 9 years of age. Before the SRME was applied, all subjects underwent pediatric sleep questionnaires (PSQ), lateral cephalometry, and portable sleep monitoring before expansion (T0). All subjects were treated with SRME for 2 months, followed by maintenance for the next 3 months. All subjects had undergone PSQ, lateral cephalometry, and portable sleep monitoring after expansion (T1). Adenoidal-nasopharyngeal ratio (ANR), upper airway width and hyoid bone position were measured by lateral cephalometry. The data before and after SRME were statistically analyzed with frequency analysis and Wilcoxon signed rank test. As reported by PSQ, the total PSQ scale was declined significantly from 0.45 (T0) to 0.18 (T1) (p = 0.001). Particularly, snoring, breathing, and inattention hyperactivity were significantly improved (p = 0.001). ANR significantly decreased from 0.63 (T0) to 0.51 (T1) (p = 0.003). After maxillary expansion, only palatopharyngeal airway width was significantly increased (p = 0.035). There was no statistically significant difference in position of hyoid bone after expansion (p = 0.333). From analysis of portable sleep monitoring, changes in sleep characteristics showed a statistically significant decrease in AHI and ODI, and the lowest oxygen desaturation was significantly increased after SRME (p = 0.001, 0.004, 0.023). In conclusion, early diagnosis with questionnaires and portable sleep monitoring is important. Treatment using SRME will improve breathing of children with SDB.