• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.94-101
• /
• 1994

About vibration model of Six-degrees-of-freedom(DOF), in mass load, examined results for knowing dynamic interference and response variation is as follows; In case of putting mass load upon the object, experimented results on two-degrees-of-freedom of the translation-1 direction and the rotation-1 direction at open-loop-control system, about 0.19 arcsed in input of the translation-$0.1{\mu}m$ and $0.022{\mu}m$ on input of the rotation-0.5 arcsec, the justicse of motion equation is acknowledged as confirming the appearance of the interference-$0.022{\mu}m$. In establishing calculation of transformation matrix by using analogue circuit, as simulating results that used incomplete differentiation, interference is $1.7{\times}10^{-3}$ arcsec on input of the translation-$0.1{\mu}m$ and $1.4{\times}10^{4}{\mu}m$ on input of the rotation-0.5 arcsec in open-loop-control system. Also it is $4.2{\times}10^{-4}$ arcsec on input of the translation-$0.1{\mu}m$ and $5.6{\times}10^{-5}{\mu}m$ on input of the rotation-0.5 arcesc in closed-loop-control system. As closed-loop-control system is better than open-loop-control system, equivalent accordance is confirmed on original response. Finally, fundamental validity of this theory is acknowledged.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.36-43
• /
• 2010

A GEO satellite launched by Arian 5 ECA launcher will be located in a transfer orbit where it requires several Apogee burn maneuvers to reach the target orbit. To obtain the required performance of Apogee burn maneuvers, a calibration of gyro drift error needs to be performed before each maneuver. In this paper, a unique gyro calibration scheme which is applied to COMS is described and the calibration error budget analysis is performed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.364-367
• /
• 2017

The basic design concept of the DACS(Divert and Attitude Control System) propellant is presented and the geometry optimization of the DACS propellant with limited outer diameter and maximum burning rate of the propellant is performed. Two-side burning surface conditions burned at the core and the one side of the propellant are applied to the propellant. And the optimized values for the radius of core, length of propellant, angle of end-side surface are obtained by the PSO algorithm. The direction for DACS propellant design is suggested by analyzing optimized design points for various burning rate.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.98-106
• /
• 2018

With the advancement in technology, miniaturization, integration, and weight reduction of satellite components have become possible. In this regard, existing medium and large satellites have been replaced by small satellites. As the demand for small satellites increases, the need for micro-thrusters has emerged for precise attitude and position control. A laser ablation micro-thruster, which generates thrust by using ablation jets that offer a wide range of thrusts and low-impulse thrusts, is considered as an alternative for micro-thrusters in small satellites. The objective of the present study is to introduce configurations of the laser ablation micro-thruster and its research trend.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.2
• /
• pp.209-218
• /
• 2019

This study proposes a new approach to Control the Orientation and position based on obstacle avoidance technology by multi sensors fusion and autonomous travelling control of mobile robot system for implimentation of Smart FA. The important focus is to control mobile robot based on by the multiple sensor module for autonomous travelling and obstacle avoidance of proposed mobile robot system, and the multiple sensor module is consit with sonar sensors, psd sensors, color recognition sensors, and position recognition sensors. Especially, it is proposed two points for the real time implementation of autonomous travelling control of mobile robot in limited manufacturing environments. One is on the development of the travelling trajectory control algorithm which obtain accurate and fast in considering any constraints. such as uncertain nonlinear dynamic effects. The other is on the real time implementation of obstacle avoidance and autonomous travelling control of mobile robot based on multiple sensors. The reliability of this study has been illustrated by the computer simulation and experiments for autonomous travelling control and obstacle avoidance.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.7
• /
• pp.637-648
• /
• 2007

This paper presents a sensor fusion method based on indirect Kalman filter(IKF) for error compensation of low-cost inertial sensors and its application to the determination of attitude and position of small flying robots. First, the analysis of the measurement error characteristics to zero input is performed, focusing on the bias due to the temperature variation, to derive a simple nonlinear bias model of low-cost inertial sensors. Moreover, from the experimental results that the coefficients of this bias model possess non-deterministic (stochastic) uncertainties, the bias of low-cost inertial sensors is characterized as consisting of both deterministic and stochastic bias terms. Then, IKF is derived to improve long term stability dominated by the stochastic bias error, fusing low-cost inertial sensor measurements compensated by the deterministic bias model with non-inertial sensor measurement. In addition, in case of using intermittent non-inertial sensor measurements due to the unreliable data link, the upper and lower bounds of the state estimation error covariance matrix of discrete-time IKF are analyzed by solving stochastic algebraic Riccati equation and it is shown that they are dependant on the throughput of the data link and sampling period. To evaluate the performance of proposed method, experimental results of IKF for the attitude determination of a small flying robot are presented in comparison with that of extended Kaman filter which compensates only deterministic bias error model.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.762-765
• /
• 2021

In this paper, an automotive ECU (electronic control unit) with Kalman filter accelerator is designed and implemented. RISC-V is exploited as a processor core. Accelerator for Kalman filter matrix operation, CAN (controller area network) controller for in-vehicle network, and LIN (local interconnect network) controller are designed and embedded. Kalman filter operation consists of time update process and measurement update process. Current state variable and its error covariance are estimated in time update process. Final values are corrected from input measurement data and Kalman gain in measurement update process. Usually floating-point multiplication is exploited in software implementation, but fixed-point multiplier considering accuracy analysis is exploited in this paper to reduce hardware area. In 28nm silicon fabrication, its operating frequency, area, and gate counts are 100MHz, 0.37mm², and 760k gates, respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.10
• /
• pp.738-746
• /
• 2019

Instead of hydraulic actuation systems, an electromechanical actuation system is more efficient in terms of weight, cost, and test evaluation in the thrust vector control of the 7-ton gimbal engine used in the Korea Space Launch Vehicle-II(KSLV-II) $3^{rd}$ stage. The electromechanical actuator is a kind of servo actuator with position feedback and uses a BLDC motor that can operate at high vacuum. In the case of the gimballed rocket engine, a synthetic resonance phenomenon may occur due to a combination of a vibration mode of the actuator itself, a bending mode of the launcher structure, and an inertial load of the gimbals engine. When the synthetic resonance occurs, the control of the rocket attitude becomes unstable. Therefore, the requirements for the stiffness have been applied in consideration of the gimbal engine characteristics, the support structure, and the actuating system. For the 7-ton gimbal engine of the KSLV-II $3^{rd}$ stage, the stiffness requirement of the actuation system is $3.94{\times}10^7N/m$, and the direct drive type electromechanical actuator is designed to satisfy this requirement. In this paper, an equivalent stiffness analysis model of a direct drive electromechanical actuator designed based on the stiffness requirements is proposed and verified by experimental results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.3
• /
• pp.187-194
• /
• 2020

In this study, computational analyses are carried out to investigate the interference flows and the aerodynamic characteristics of a hit-to-kill intercepter due to lateral jets at medium altitude. In addition, the analyses are performed for air and multi-species gas used in the side jet. The results indicate that the position of the barrel shock are shifted upstream and the structure of the shock wave are changed for the multi-species jet when compared to the air jet. As a result, the high pressure region with multi-species jet moves forward and the pitching moment is higher under the same flow condition. Moreover, the inclusion of high temperature effects makes drastic changes in pressure distribution. The jet width is much bigger, and the jet diffuses over wider range in medium altitude than in low altitude, because of the low density of the freestream.

• Journal of the Institute of Convergence Signal Processing
• /
• v.11 no.4
• /
• pp.338-344
• /
• 2010

Both ends of welding line are often closed by wall in the welding of ship blocks. In this research, seam tracking sensing system for butt welding in the condition with wall was developed. Seam tracking sensing system measures position of carriage from wall and detects root-pass of welding line. The system consists of the laser displacement sensors and ultrasonic sensors. The laser displacement sensor reciprocal1y rotates by the motor and measures a distance from laser sensor to the welding material. The ultrasonic sensor measures a distance between welding system and walls. The distance measured by the ultrasonic sensor is used to get X(driving) position and to determine initial and end point of the weld line. Y(weaving) and Z(height) of the weld line are obtained by the distance measured by the laser displacement sensor and the orientation of the sensor. The sensing system includes the controller that is independent from the welding carriage. The seam tracking sensing system is attached to both side of welding carriage so that interference between welding torch and sensing system can be avoided during the welding. And both side sensing system minimize dead zone. Finally, developed sensing system was adhered to welding carriage and verified usefulness by experiments.