• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.447-456
• /
• 2001

Many investigators have tried to represent the nonlinear behavior of stress-strain relationship of concrete using mathematical curves. Most of empirical expressions for stress-strain relationship, however, have focused on old age concrete, and were not able to represent well the behavior of concrete at an early age. Where wide understanding on the behavior of concrete from early age to old age is very important in evaluating the durability and service life of concrete structures. In this paper, effect of 5 different strength levels and ages of from 12 hours to 28 days on compressive stress-strain relationship was observed experimentally and analytically. Tests were carried out on $\phi$100${\times}$200mm cylindrical specimens water-cured at 20${\pm}$3$^{\circ}C$. An analytical expression of stress-stain relationship with strength and age was developed using regression analyses on experimental results. For the verification of the proposed model, the model was compared with present and existing experimental data and some existing models. The analysis shows that the proposed model predicts well experimental data and describes well effect of strength and age on stress-strain relationship.

• Journal of Energy Engineering
• /
• v.21 no.4
• /
• pp.362-372
• /
• 2012

The steam generator tubes of nuclear power plants are pressure boundaries, and if tubes are leaked, the coolant with the radioactive materials was flowed out from the primary system to the secondary system and polluted the plant and the air. Recently most crack defects of tubes are stress corrosion cracks and these defects are located in expansion transition area, sludge pile-up region, and U-bend area. The most effective one of crack initiation factors in expansion transition area and U-bend area is the residual stress. According to the experiences of Korea standard nuclear plants(Optimized Power Reactor-1000), they had the stress corrosion cracks at the tube expansion transition area in early operating stage and especially lots of circumferential cracks were occurred. Therefore in this study, the distributions and conditions of residual stresses by tube expansion methods were compared and the dominant reason of a specific direction was examined.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.5
• /
• pp.409-414
• /
• 2017

In the thin strip coiling process, it is necessary to use a sleeve with a mandrel to prevent excessive deformation of the strip. The stress distribution in the sleeve and strip is an important factor to determine the size of the sleeve. However, an experimental approach is almost impossible because of the accumulation of high pressure. A finite element (FE) model of the strip coiling process was developed in this study. Then, the radial and hoop stresses on the sleeve and strip were investigated using FE analyses. The theoretical values and analysis results under idealized conditions were compared to verify the FE model. The effect of the strip thickness on the stress distribution was also investigated. The radial stress increased by 6.3 times for a 1-mm-thick strip at the coil starting point. The radial stress at the sleeve increased by 14.8 % with a stacked thickness of 90 mm because of the reaction force applied by the mandrel.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.176-176
• /
• 2011

환형수조는 점착성 퇴적물의 이송특성 연구를 위해 가장 선호되는 실험 장치로 알려져 있다. 과거 많은 연구자들은 퇴적물의 이송특성, 특히 침식/퇴적 특성 조사를 위해 주로 수로를 이용한 실험적 연구를 수행하였는데, 최초의 실험적 연구들은 주로 직선수조에서 수행되었다. 그러나 입자간의 응집이 중요한 역할을 하는 점착성 퇴적물의 경우에, 직선수조 끝단에서의 자유낙하 및 재순환 펌프의 날개에 의해 응집된 토사가 쉽게 분리될 수 있어 그 타당성이 의문시 되어 왔으며, 이러한 단점을 보완하기 위해 환형수조가 고안되었다. 환형수조는 수면과 접하여 회전하는 상부링의 마찰력에 의해 흐름이 생성되기 때문에 시간의 제약 없이 흐름조건을 동일하게 만들 수 있다는 큰 장점을 갖는다. 그러나 환형수조는 원주유속의 속도차이 및 원심력으로 인한 2차 순환류를 형성시켜 반경 방향(radial direction)에서의 바닥전단응력을 불균일하게 하는 단점을 갖는다. 이러한 2차 순환류와 바닥전단응력의 불균일을 저감시키기 위하여 환형수조의 몸체를 상부링의 회전 방향과 역방향으로 직접 회전시키는 방법이 채택되어져 왔다. 한편, 환형수조의 상부링과 몸체를 서로 역방향으로 동시에 회전시키는 양방향 회전(counter-rotation)의 적용을 위해서는 2차 순환류가 최소가 되며 바닥전단응력이 균일해지는 최적 회전속도비에 대한 분석은 필수적 사항이다. 이를 위하여, 상부링과 몸체의 회전속도에 따라 변화하는 수조내부의 흐름특성 및 평균바닥전단응력에 대한 연구가 선행되어야만 한다. 이에 본 연구에서는 전산유체역학을 이용하여 전북대에 설치된 환형수조의 상부링과 몸체의 회전속도에 따라 변화하는 수조내부에서의 흐름특성 및 바닥전단응력에 대한 분석이 수행되었다. 또한, 이를 기초로, 환형수조의 최적 회전속도비 산출을 위한 연구가 수행 중에 있다. 이러한 결과들은 추후 환형수조를 이용한 점착성 퇴적물의 침식/퇴적 등과 같은 이송특성 연구시, 퇴적물에 작용하는 흐름조건의 정밀산정을 위한 기초자료로 활용될 수 있을 것이다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.828-834
• /
• 2002

In this paper, for the mixed mode fatigue problem, the method of determining testing load was proposed. It is based on the plastic zone size and the limited maximum stress intensity factor by ASTM STANDARD E 647-00. The application method of maximum tangential stress criterion and the stress intensity factor for the finite width specimen was proposed. In the result of applying the method to mixed mode fat gut test for A5052 H34, it obtained the satisfactory experimental results on the stable crack growth.

• 한국가스학회:학술대회논문집
• /
• 2003.10a
• /
• pp.53-58
• /
• 2003

API 5L X65 배관에 50mm이상의 단관을 삽입하여 용접하였을 경우, 삽입된 단관 길이 변화에 따른 용접부 기계적 특성 평가 결과를 요약하면 다음과 같다. 1. 단관삽입 용접부위의 거시적 조직관찰, 미소경도측정, 인장시험, 굽힘시험을 수행한 결과, 단관삽입 용접부의 건전성에는 문제가 없는 것으로 평가되었다. 2. 단관삽입 용접부의 원주방향 최대 인장 잔류응력의 크기는 단관 삽입 길이에 관계없이 약 150MPa로서 그리고 최대 압축 잔류응축은 약 300MPa로 측정되었다. 모재의 항복강도가 492MPa인 것과 비교하여보면 단관 삽입 용접에 의한 잔류응력의 영향은 매우 작은 것으로 평가되었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.5 no.4
• /
• pp.354-361
• /
• 1981

This study aims to compare stress concentratior factors in a loaded elastic body of the infinite plate with pressure coefficients of a fluid in the potential flow. First in view of hydrodynamics, when a single elliptic cylinder in the form of a bluff body stands in the potential flow, the pressure distribution(doefficient, C$\_$p/around the elliptic cylicder which is changed according to the position(angular displacements)is theoretically analyzed and calulated; secondly, in view of theory of elasticity, when an eliptic hole which is made on a flat plate gets tension, the stress distribution(factor) around the elliptic hole which is changed according to the position(angular displacements )is theoretically(K$\_$t/) and experimentally (K$\_$e/) measured; and finally. The results are compard and examined.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.430-434
• /
• 2001

To perform the integrity evaluation of RPV more realistically, it is necessary to evaluate the metallurgical microstructure and residual stress considering more real phenomena such as multi-pass welding process and PWHT. Accordingly, firstly, this paper proposes the integrated assessment methodology systematically developed for residual stress on weldment of RPV by using thermodynamics, diffusion theory, finite element method and validation experiment. Also, the residual stress on circumferential weldment of reactor pressure vessel is calculated considering multi-pass welding process by the commercial finite element package, ABAQUS.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.6
• /
• pp.938-945
• /
• 2012

This research proposes FEM analysis for Tandem welding process used in wind tower and predicts optimal welding process to improve the stability of welded structures. Three dimensional elasto-plastic analyses are employed to evaluate thermo-mechanical behavior of residual stress and deformation during Tandem welding for different distance between two touches. To confirm the thermal distribution, Goldak's ellipse heat source model and the real size wind tower pipe model are utilized. Four different analyses are being performed, where in each case the distance between two electrode torches is being changed and residual stress and welding deformation are predicted. Depending on base material state, each case is divided into: Liquid (100mm), Austenite+Liquid (200mm), Austenite+Cementite (400mm), Pearlite+Cementite (800mm).

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.115-121
• /
• 2008

A knowloedge of the residual stress distribution at circumferential welds can increase the prediction accuracy of a fracture assessment in pipe lines. In this study, in order to predict the residual stress distribution in the circumferential butt-welded pipes were measured, using the hole-drilling strain gauge method. Their practical applications were performed in to two kinds of pipes. As the results, the following characteristics were found. On the inner surface of pipes, the circumferential and axial residual stresses were both tensile near the center line of welding and both of them changed from tensile to compressive as the distance from the center line increased. On the outer surface, however, the circumferential residual stress was shown to be tensile wile the axial residual stress was compressive near the center line of welding, and later they were revered at the region far away from the centerline.