• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2002.11a
• /
• pp.13-18
• /
• 2002

증기 발생기 전열관의 파열 사고는 지난 20년 동안 2년마다 1개씩의 비율로 발생되어왔고 최근 몇 년간은 매년 발생되고 있는 추세이다(3). 전열관의 파열 사고는 응력부식균열, 피로 그리고 마멸 등의 원인에 의해서 발생되고 있는 것으로 알려져 있다. 초기 발전소에서 균열의 발생 및 성장은 축 방향 균열에 국한하여 관심을 가졌었으나 최근 원주 방향 균열에 의한 사고가 발생되면서 원주 방향 균열에 대해 관심을 가지게 되었다.(중략)

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.1
• /
• pp.104-110
• /
• 1997

To predict the effect of ring expansion and ring compression on residual stress relief of Al 7175 ring rot]s, 2-D axisymmetric thermal analysis and elastoplastic analysis were performed. The residual stress distributions along the thickness of T73, T7351 and T7352 treated rings were measured using three step sectioning method. The measured results were compared to numerical ones for quenched and stress relieved rings. After quenching, calculated hoop and axial residual stresses were similar to measured ones for T73 treated rings. The residual stresses of T7351 and T7352 treated rings were decreased remarkably compared to T73 treated rings. The effect of axial residual stress relief was superior to that of hoop one, and also ring compression to ring expansion. It was concluded that ring compression is advantageous over ring expansion in view of stress relief effect and practicality, and vice versa in view of dimensional control and press power.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.263-269
• /
• 2003

Magnetic flux leakage (MFL) signals were used for corrosion inspection of buried oil and gas pipeline. 3D finite element analysis was used to examine the effects of far and near-side pit depth and tensile stress on MFL signals. Anisotropci materials were used, and the effects of simulated tensile stress on MFL were investigated. The axial and radial MFL signals depended on far and near-side single pit depth and on the bulk stress, but the circumferential MFL signal did not depend on them. The axial and radial MFL signals increased with increasing pit depth and the bulk stress, but the circumferential MFL signal was scarcely changed.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.11a
• /
• pp.243-250
• /
• 2000

배관을 지하에 매설할 경우 매설배관이 묻히는 깊은 도랑을 트랜치라 하는데 이 트랜치의 폭과 깊이의 칫수를 적절하게 결정하는 것은 매설배관의 건전성을 유지하는데 중요한 인자중의 하나이다. Watkins는 매설배관의 트랜치 폭에 대한 연구를 수행하여 최근 그 결과를 발표한바 있다. (1) Fig. 1에 트랜치와 배관의 단면도를 그리고 일반적으로 사용하는 기술적인 용어를 나타내었다.(중략)

• Journal of Aerospace System Engineering
• /
• v.17 no.2
• /
• pp.1-8
• /
• 2023

Power transmission shafts in rotary wing aircraft use a hollow shaft to reduce weight. We can apply linear elastic fracture mechanics to predict crack propagation behavior. This paper predicted crack growth life of a hollow shaft with a circumferential through-type crack by finite element analysis. A 2D finite element model was created by applying a torsion and forming elements considering cracks. We defined the initial crack length and performed the finite element analysis by increasing the crack length to derive stress intensity factor at crack tips. We defined the length just prior to the stress intensity factor exceeding the fracture toughness as the crack limit length. We calculated the crack limit length using a handbook and numerically integrated the crack growth rate equation to derive growth life of each crack. The growth life of each crack was compared to verify the proposed finite element analysis method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1207-1214
• /
• 2014

Under excessive plasticity, the fracture toughness of a material depends on its size and geometry. Under fully yielded conditions, the stresses in a material near its crack tip are not unique but rather depend on the geometry. Therefore, the single-parameter J-approach is limited to a high-constraint crack geometry. The JQ theory has been proposed for establishing the crack geometry constraints. This approach assumes that the crack-tip fields have two degrees of freedom. In this study, the crack-tip stress field of a fully circumferential surface-cracked pipe under combined loads is investigated on the basis of the JQ theory by using finite element analysis. The combined loads are a tensile axial force and the thermal gradient in the radial direction. Q-stresses of the crack geometry and its loading state are used to determine the constraint effects. The constraint effects of secondary loading are found to be greater than those of primary loading. Therefore, thermal shock is believed to be the most severe loading condition of constraint effects.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.1
• /
• pp.41-49
• /
• 1991

A knowledge of the resdual stress distribution at circumferential weldments can normally increase the accuracy of a fracture assessment in pipe line. In this paper, we present the measurements about the residual stress distributions at three kinds of circumferential butt welded pipes using the holl drilling strain gage method. By this experiment, we have obtined the following characteristics. At the inner surface of the pipe region near the center line of welding is under high tensile residual stress. However, as the distance from the center line of welding increases, the tensile component decreases and finally becomes compressive residual stress at region far away from the center line of welding. The longitudinal residual stress at the outer surface is compressive regardless of the diameter of pipe and the circumferential stress is changed from compressive to tensile as pipe diameter increases. The results also demonstrate that the residual stress is mainly caused by self-restraint bending force in the pipe welding.

• Nuclear Engineering and Technology
• /
• v.20 no.4
• /
• pp.241-245
• /
• 1988

It is very important to investigate the behaviors of the material parameters governing PCI fuel failure during power ramp because PCI fuel failure is considered to be related to the operations limits of power reactors. In this study, the behavior characteristics of the material parameters such as hoop stress, hoop strain, ridge height, creep strain rate and strain energy in cladding were studied as a function of the operating parameters such as power shock and ramp rate. The FEMAXI-IV fuel rod performance analysis code was used for this study.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.5
• /
• pp.453-460
• /
• 2015

Since the Fukushima nuclear accident, several researchers are extensively studying the effect of torsion on the piping systems In nuclear power plants. Piping installations in power plants with a circumferential crack can be operated under combined loading conditions such as bending and torsion. ASME Code provides flaw evaluations for fully plastic fractures using limit load criteria for the structural integrity of the cracked pipes. According to the recent version of Code, combined loadings are provided only for the membrane and bending. Even though actual operating conditions have torsion loading, the methodology for evaluating torsion load is not established. This paper provides the results of limit load analyses by using finite element models for circumferentially cracked pipes under pure bending, pure torsion, and combined bending and torsion with tension. Theoretical limit load solutions based on net-section fully plastic criteria are suggested and verified with the results of finite element analyses.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2008.04a
• /
• pp.149-154
• /
• 2008

도시가스용 배관으로 사용하고 있는 폴리에틸렌 배관은 유연하여 시공이 용이할 뿐만 아니라 부식 및 전식이 일어나지 않아 유지관리가 편리하고 교체 없이 50년 이상 사용이 가능하여 금속 소재에 비하여 경제적이기 때문에 그 사용량이 증가하고 있다. 그러나 차량의 증가 등으로 인하여 매설된 배관에 많은 응력이 집중되고 있다. 따라서 토하중 뿐만 아니라 증가한 차량 등에 의한 하중이 복합적으로 작용할 경우에 매설된 배관이 어느 정도의 응력을 받고 있는지를 검토하고자 하였다. 직경이 $50{\sim}400mm$인 배관을 대상으로 매설깊이를 $0.6{\sim}1.2m$로 변화시키고 사용압력을 $0.4{\sim}4bar$로 변화시켜 그 결과를 검토하였다. 결과는 수식해와 유한요소 해석 방법을 이용하여 계산하였으며 두 결과를 비교하여 유한요소 해석 방법의 신뢰성을 높였다. 두 해석방법 모두 내압에 의한 영향, 토양하중에 의한 영향 그리고 차량 하중에 의한 영향을 각각 계산하였다. 그리고 각 하중이 복합적으로 작용할 경우에 대한 응력을 계산하여 매설 깊이에 따라 배관에 발생하는 응력을 계산하였다. 또한 가스배관 설계에 사용하는 허용응력을 4가지로 구분하여 발생한 응력과 비교하여 그 안전성을 검토하였다. 수식해와 유한요소 해석 결과를 비교하여 각각의 결과를 검증한 결과 수식해가 유한요소 결과보다 약간 높은 응력값을 나타내었으며 내압, 토하중, 차량하중 등이 복합적으로 작용할 경우에 매설깊이가 1m일 때 가장 낮은 원주방향응력이 발생하였다.