• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.7
• /
• pp.666-673
• /
• 2008

To construct the accurate radio satellite navigation system, the efficient communication each satellite with the ground station is very important. Throughout the communication, the orbit of each satellite can be corrected, and those information will be used to analyze the satellite satus by the operator. Since there are limited resources of ground station, the schedule of antenna's azimuth and elevation angle should be optimized. On the other hand, the satellite in the medium earth orbit does not pass the same point of the earth surface due to the rotation of the earth. Therefore, the antenna pass schedule must be updated at the proper moment. In this study, Q learning approach which is a form of model-free reinforcement learning and genetic algorithm are considered to find the optimal antenna schedule. To verify the optimality of the solution, numerical simulations are conducted.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.9
• /
• pp.657-662
• /
• 2022

In this paper, the calculation using simulation and two measurement methods for G/T of the telemetry are analyzed. Antenna gain and noise temperature are calculated by using ICARA and Antenna Noise Temperature Calculator. System G/T were calculated by using Antenna gain/noise temperature, LNA gain/noise temperature, cable loss. The first G/T measurement method is Y-factor measurement method, which is to calculate G/T by comparing LNA noise temperature and a signal level difference when an antenna and a 50ohm termination are respectively connected to an LNA input terminal Second method is Solar calibration measurement method that is to calculate G/T by comparing noise level difference when looking at the sun and lowest level point. Finally, the accuracy was reviewed by comparing the G/T calculation results with the two measurement methods, and the optimal measurement method according to antenna performance and operating environment was presented.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.3-16
• /
• 2011

천리안 위성은 4개 정부 부처 공동 사업으로, 통신 서비스, 해양 기상 관측 서비스 제공을 목적으로 개발된 복합 위성으로, 그중 통신 서비스를 담당하는 통신 탑재체는 방송통신위원회 출연으로 한국전자통신연구원(ETRI)가 주관, 개발하여 성공한 순수 국산 개발품으로, 위성 발사 성공 후 시험 검증을 거쳐 현재 정상 운용 중에 있다. 우주 인증 획득을 목적으로 개발한 통신 탑재체는 위성 스위칭 중계기와 다중 빔 안테나로 구성되었으며, 구성 부품들인 능동 부품과 수동 부품들은 대부분 국내 연구진에 의해 설계, 제작 시험 검증되어 중계기 및 안테나 시스템 종합화, 통신 탑재체 및 위성체 우주 환경 시험을 성공적으로 수행되었다. 위성 발사 성공 후에, 정지 궤도상에서의 통신 탑재체 궤도내 시험을 완료를 통해 순수국산 개발된 통신 탑재체의 설계 제작 기술에 대한 정지 궤도 우주환경에서도 정상 동작됨을 입증하였다. 통신 탑재체는 다양한 우주 조건에서의 다양한 기술 확보와 차세대 멀티미디어 위성 서비스 개발에 활용하고자 한다. 본 논문은 통해기 통신 탑재체 설계 제작 시험 기술을 소개하고, 활용 계획에 대해 언급하고자 한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.4
• /
• pp.306-314
• /
• 2018

A two-axis gimbal-type X-band antenna for CAS(Compact Advanced Satellite) transmits large amount of image data to ground station regardless of satellite attitude and orbital motion. This antenna mounted on the external surface of the satellite is directly exposed to the extreme space with thermal environment during the orbital operation. Therefore, a proper thermal design is needed to maintain the antenna itself as well as other main components within allowable temperature range. In this study, the thermal design effectiveness of two-axis gimbal X-band antenna was verified through the thermal analysis. In addition, required power and duty cycle of heater were estimated through the thermal analysis under conditions of system level thermal vacuum test and on-orbit thermal environment. The thermal analysis results indicated that all the main components of X-band antenna satisfy the allowable temperature requirement.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.8
• /
• pp.683-691
• /
• 2014

Significance of SAR(Synthetic Aperture Radar) satellite regadless of weather have grown for Earth observation. According to the cost-effective trend in satellite development, SAR antenna is actively studied. It's a competitive candidate to use deployable SAR antenna out of CFRP. In this study, variables for an antenna configuration model was researched and evaluated. The design of the antenna was structurally analyzed by FEM(Finite Element Model). Tool-kit was developed for modifying the SAR antenna model easily in accordance with system requirement change. In the tool-kit, antenna configuration design and error analysis of the antenna surface could be achieved. And compatibility of tool-kit results to CST, a RF analysis program, was confirmed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.2
• /
• pp.118-126
• /
• 2003

• Bulletin of the Korean Space Science Society
• /
• 2007.10a
• /
• pp.123.1-123.1
• /
• 2007

• Bulletin of the Korean Space Science Society
• /
• 2007.10a
• /
• pp.120.2-120.2
• /
• 2007

• Aerospace Engineering and Technology
• /
• v.12 no.2
• /
• pp.140-146
• /
• 2013

In this study, we discuss about the printed reflectarray antenna design for parabolic reflector volume reduction. For this, we simulated and measured the phase characteristics of the unit array element of reflectarray antenna using waveguide simulator. As a results, the maximum phase variation is $298^{\circ}$ by simulation, the average phase variation is $309^{\circ}$ by measurement in 10GHz. And the printed Reflectarray antenna gain is 28.3dBi, 3dB beamwidth is E-plane $5.1^{\circ}$, H-plane $5.2^{\circ}$, sidelobe level is E-plane -11.4dB, H-plane -17.6dB.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.3
• /
• pp.279-288
• /
• 2011

This paper will discuss the alignment techniques and measurement results of geostationary satellite communication antennas for correct antenna pointing and also the fixtures. To get the best performance in terms of antenna pointing and fixtures, zero G condition have been simulated and laser tracker and theodolite system have been applied. As a result, alignment stability was verified within the tolerance, ${\pm}\;0.25mm$ and ${\pm}\;0.013^{\circ}$ and finally Ka-band deployable antenna alignment has been accomplished within the tolerance, ${\pm}\;0.5mm$ and ${\pm}\;0.015^{\circ}$.