• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1210-1216
• /
• 2011

The purpose of this study is to establish the analysis method for prediction of temperature during cryogenic heat treatment. Experimental cryogenic heat treatment is conducted to observe the phenomena such as boiling of fluid, ice layer on the material surface and to measure the temperature distribution of Al6061 tube. The CFD analysis considering the observed phenomena in the experiment is performed to predict the temperature distribution and convection heat transfer coefficient at each stage of cryogenic heat treatment, in which the boiling of fluid is considered as the multi-phase condition of vapour and liquid. The formation of ice layer on the tube surface is also modeled between material and fluid. The predicted results are in good agreement with the experimental ones. From the results, it is shown that the analysis method can predict the temperature distribution and convection heat transfer coefficient during cryogenic heat treatment.

• 열처리공학회지
• /
• 제28권4호
• /
• pp.190-199
• /
• 2015

The study is intended to investigate the effect of solution treatment on microstructure and corrosion behavior of AZ91(Mg-9%Al-1%Zn-0.3%Mn)-2%Ca casting alloy. In as-cast state, the AZ91-2%Ca alloy consisted of intermetallic ${\beta}(Mg_{17}Al_{12})$, $Al_8Mn_5$ and $Al_2Ca$ phases in ${\alpha}-(Mg)$ matrix. After the solution treatment, Al within the ${\alpha}-(Mg)$ matrix was distributed more homogeneously, along with the slight decrease in the total amount of intermetallic compounds. The corrosion resistance of the AZ91-2%Ca alloy was improved after the solution treatment. The microstructural examinations for the solution-treated samples revealed that the better corrosion resistance may well be related to the incorporation of more oxides and hydroxides such as $Al_2O_3$, $Al(OH)_3$, CaO and $Ca(OH)_2$ into the surface corrosion product without dissolution of the intermetallic phases along the grain boundaries.

• 열처리공학회지
• /
• 제33권6호
• /
• pp.277-283
• /
• 2020

Cu-Co-Si based alloy has a strengthening mechanism for Co₂Si intermetallic compounds deposited on the copper matrix after aging treatment and the solution treatment has a key influence on the strength and electrical conductivity of the final products. In this paper, the Cu-1.6%Co-0.38%Si alloy was fixed at the time and the solution treatment temperature was set at a temperature in the range of 800 to 950℃, and the change in mechanical properties was observed by fixing the temperature at 950℃ and changing the time. The microstructure was observed using an electron microscope and an optical microscope, and the changes in hardness, electrical conductivity, and bending workability after aging treatment were investigated. When the solution treatment time is less than 20 seconds, the solution treatment is not sufficient and the formation of precipitates contributing to the increase in hardness decreases and the hardness decreases after the aging treatment, and in more than 50 seconds, the hardness decreases due to the coarsening of the grains and the bending workability got worse.

• 한국산업융합학회 논문집
• /
• 제24권3호
• /
• pp.261-269
• /
• 2021

This study was evaluated the elastic wave properties according to tension of Incoloy 825 alloy with different solution treatment temperature and aging time. Solution treatment was carried out at 700, 800, 900, and 1000 ℃ for 1 hour, and aging was carried out at 700 ℃ for 1, 5, 10, and 30 hours. As the solution treatment temperature increased, the tensile strength decreased and the elongation increased. However, as the aging time increased, the tensile strength increased and the elongation decreased. The dominant frequency decreased as the solution treatment temperature increased, but increased as the aging time increased. The dominant frequency according to the solution treatment and aging time increased as the tensile strength increased, but increased despite the decrease in elongation.

• 열처리공학회지
• /
• 제35권6호
• /
• pp.295-302
• /
• 2022

The present study aims to investigate the effect of Al content on microstructure and hardness of discontinuous precipitates (DPs) formed by continuous cooling (CC) in Mg-8%Al and Mg-9.5%Al alloys. The DPs had a wide range of (α+β) interlamellar spacings, which may well be attributed to the different transformation temperatures during CC. The higher Al content gave rise to the higher level of interlamellar spacings of the DPs, and thicker and larger amount of β phase layer in the DPs. It is noticeable that the Mg-9.5%Al alloy exhibited higher hardness of the DPs than the Mg-8%Al alloy, but the ratio of increase in hardness of the DPs compared to that of the as-cast state was similar regardless of the Al content. The reason was discussed based on the differences in microstructures of the DPs for the Mg-8%Al and Mg-9.5%Al alloys.

• 열처리공학회지
• /
• 제36권4호
• /
• pp.223-229
• /
• 2023

This work was intended to investigate the effects of Zn content on microstructure and hardness of discontinuous precipitates (DPs) produced by continuous cooling (CC) in Mg-8%Al-X%Zn alloys with 0%, 0.5% and 1% of Zn contents (wt%). The DPs in the alloys possessed a wide range of (α+β) interlamellar spacings, which is attributed to the different transformation temperatures during CC. The higher Zn content resulted in the lower level of interlamellar spacings of the DPs, along with thinner and larger volume fraction of β phase layer in the DPs. It is noted that the DPs in the alloy with higher Zn content exhibited higher hardness, and that the ratio of increase in hardness of the DPs to that of the as-cast state was also increased with increasing Zn content. The reason was discussed on the basis of microstructural differences of the DPs in the Mg-8%Al-X%Zn alloys.

• 대한금속재료학회지
• /
• 제47권3호
• /
• pp.175-181
• /
• 2009

Mechanical properties and precipitation behavior of backward extruded 6061 Al alloy for pressure vessel were investigated using tensile test, transmission electron microscopy (TEM) and differential scanning calorimeter (DSC). In this study, solution heat treatment (SHT) was performed at $535^{\circ}C$ for 30~90 min and aging treatment was conducted at 177 and $190^{\circ}C$ for 1~7 h. Maximum tensile strength of $36.6kgf/mm^2$ and yield strength of $33.29kgf/mm^2$ were achieved at the aging time of 5 h at $190^{\circ}C$. TEM observation showed that fine needle-like ${\beta}^{{\prime}{\prime}}$ phase which has 35~45 nm of length was uniformly distributed in the aged 6061 Al alloy specimen. From tensile test, TEM and DSC analysis, it is expected that aging time of 2~5 h at $190^{\circ}C$ is suitable for the extruded A6061 used as pressure vessels.

• Journal of Welding and Joining
• /
• 제12권1호
• /
• pp.38-43
• /
• 1994

고강도 알루미늄합금은 중량이 가벼우면서 인장강도와 항복강도가 높고 가공성, 성형성이 좋아 항공기, 자동차, 선박 등 수송용 재료로 각광을 받고 있으며, 이 중 Al-Zn-Mg계(7000계) 알루미늄 합금은 용접 구조물용 경량소재로 활용범위가 높다. Al-Zn-Mg계 알루미늄 합금은 고온에서 용체화 처리후 저온으로 급냉시킨 재료를 자연시효 또는 인공시효처리를 하여 이 때 석출되는 시효 석출물에 의해 강도를 증가시킨 석출 경화형 합금이다. 그런데, 7000계열 알루미늄합금은 적절한 열처리 작업을 통해 최적의 기계적 성질이 얻어지도록 합금설계가 되어있기 때문에 구조물 제작시 용접에 의한 ARC 열을 받게 되면 열이력(thermal cycle)에 의해 모재의 미세조직이 변화하고 용접 결함이 발생하며 강도의 약화와 함께 내식성 등이 저하한다. 따라서 고강도 알루미늄합금의 용접성을 향상시키기 위해서는 용접부의 미세조직거동과 용접부에 발생하는 용접결함의 현상을 조사하여 용접용 고강도 합금에 필수적으로 요구되는 용접성에 대한 검토가 충분히 이루어져야 한다. 따라서 본 고에서는 알루미늄합금, 특히 7000계열 알루미늄합금에 주목하여, 용접방법, 각종 결함과 대책, 용접부의 시효경화와 응력부식균열 및 기계적 성질 등을 지금까지 보고된 각종 자료를 기초로 하여 3회에 걸쳐 기술하고자 한다.

• 열처리공학회지
• /
• 제9권1호
• /
• pp.12-18
• /
• 1996

Austenite(${\gamma}$) grain size, ${\varepsilon}$ martensite volume fraction and damping capacity of Fe-17%Mn alloy have been investigated as a function of solution treatment temperature of $600^{\circ}C$ to $1100^{\circ}C$. With increasing the solution temperature, ${\gamma}$ grain size, ${\varepsilon}$ martensite content and damping capacity are increased, while the hardness is decreased. When ${\gamma}$ grains are small, ${\varepsilon}$ plates grow in only one direction in each ${\gamma}$ grain. However, if the ${\gamma}$ grains are large in accordance with high solution treating temperature, several ${\varepsilon}$ variants with different orientations are formed and intersected each other in each ${\gamma}$ grain. In spite of small ${\varepsilon}$ martensite content, the damping capacity of the specimen which was annealed at $700^{\circ}C$, followed by subzero treatment at $-196^{\circ}C$, is almost equal to that of the specimen annealed at $1000^{\circ}C$ and subsequently quenched to room temperature. From this result it is suggested that the damping capacity of Fe-17%Mn alloy having fine ${\gamma}$ grains is mainly attributed to the movement of ${\gamma}/{\varepsilon}$ interface without the operation of other damping sources such as ${\varepsilon}/{\varepsilon}$ boundaries and stacking faults in ${\varepsilon}$ reported previously.

• 한국결정성장학회지
• /
• 제28권6호
• /
• pp.250-255
• /
• 2018

본 연구에서는 3D-프린팅 적층 공정으로 제조한 인공관절용 CoCrMo 합금 소재의 HIP 처리를 포함한 복합열처리 후 소재의 인장특성, 내마모 특성 등의 기계적 특성과 결정구조 및 미세조직 등의 재료특성 변화를 고찰하였다. 내부마이크로 기공을 제거하기 위한 HIP 열처리와 금속탄화물 생성을 위한 상압열처리 및 금속탄화물의 균질화를 위한 용체화 열처리를 거치는 복합열처리 공정을 실시하여 인공관절 소재로서의 특성을 부여하고자 하였다. 3D-프린팅 적층 공정으로 제조한 인공관절용 CoCrMo 합금 소재의 복합열처리 효과는 HIP 공정중의 치밀화 과정, 상압열처리 중의 금속탄화물 생성 및 용체화 열처리 과정중의 금속탄화물의 균질화 효과임을 XRD, FE-SEM, EDS 분석으로 확인하였다.