• Journal of Korean Society of Steel Construction
• /
• v.10 no.1 s.34
• /
• pp.101-113
• /
• 1998

In this study, we research the influence of butt-welded joints in high tension bolted joints on the static and fatigue strength. As a results, if it's located inside or outside of the friction surface, the fatigue strength decrease, and the decrease of fatigue strength is greater in cases that the butt-welded joints exist outside of the friction surface. But the influence of butt-welded joint on the fatigue strength satisfies category B of the Specifications.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.3 s.46
• /
• pp.231-238
• /
• 2000

There was extreme improvement in the processing result of weld toe, but there is possibility that the fatigue failure occurs from the weld root part where the fatigue strength became low relatively. This study did the fatigue test at the cross rib specimens which implemented a partial penetration weld to improve the fatigue strength of the weld root part. As a result of the fatigue test of the partial penetration weld and the fillet weld specimens, almost the same fatigue strength appeared. Because the fatigue failure began from toe, there was not a reinforcement effect in the weld root part by the partial penetration weld. So, it examined fatigue strength at the partial penetration welding specimens which processed toe to stop the fatigue failure of toe part. As a result, there was big fatigue strength improvement from the partial penetration weld than the fillet weld. Therefore, if fatigue crack occurrence can be restrained from toe, it thinks that the fatigue strength of the root part can improve by the partial penetration weld, after all, it thinks that the overall fatigue life can improve.

• Journal of Welding and Joining
• /
• v.15 no.3
• /
• pp.1-11
• /
• 1997

용접이음부에서는 피로크랙 전파거동이 모재와 다르다는 것은 이미 알려져 있으며 그 원인으로서는 용접부에 있어서의 금속조직의 변화와 잔류응력 등이 일컬어 진다. 금속조직의 변화에 따른 영향에 대하여서는 비교적 그 영향이 작으며 또한 피로 크랙 전파속도에 대해서 안전한 쪽으로 역할을 한다고 보고되어져 있다. 따라서 용접 이음부에 있어서의 피로크랙 전파에 대하여서는 주로 잔류 응력의 영향에 주목하여, 잔류응력이 피로크랙의 전파속도에 어떻게 영향을 미치는가를 파악하여야 한다. 이러 한 관점에서 지금까지 용접잔류응력장을 전파하는 피로크랙을 대상으로 하여 잔류응력 이 피로크랙 전파에 미치는 영향을 정량적으로 평가하고자 하느 시도가 많은 연구진에 의해 수행되어 왔다. 표1에 이러한 연구의 흐름을 평가방법과 평가에 고려된 사항을 중심으로 나타내었다. 이러한 배경으로부터, 본고에서는 피로크랙 전파거동에 미치는 잔류응력의 영향에 대해서 지금까지 수행된 연구의 내용을 연구 발전형태에 주목하여 검토하였다.

• Journal of Welding and Joining
• /
• v.1 no.2
• /
• pp.34-44
• /
• 1983

이 논문에서는 먼저 연강 모재에 대해서 여러 가지의 반복 속도로 대기 중과 해수 중 및 3% Nacl 용액 중에서의 피로시험을 실시하고, 피로 균열 발생수명 및 전파수명에 미치는 속도의 영향을 검사함과 동시에 피로수명의 추정법에 대해서 해설한다. 그리고 연강의 완전용입 용접 이음의 toe 부에 대하여 추정한 피로 균열 발생수명과, 파랑주기에 가까운 10cpm의 반복 속도에서 피로시험을 실시하여 구한 수명과를 비교한 결과에 대해서도 소개하고자 한다.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.1
• /
• pp.37-48
• /
• 2017

In this research, 9 SAW welding specimens with 1 hour post-heat treatment (PH1) and 2 hours (PH2) were experimented to confirm the weldability and the joint performance of 60mm thickness HSA800 steel. SAW tests with PH1 & PH2, including weld impact test, bend test, hardness test, macroscopic test, and microscopic test, had a good test results. However, from the chemical composition test results, P composition was not satisfied with Korean Industrial Standards(KS). According to the weld-zone tensile tests, 2 hours post-heat SAW is recommended because the mechanical characteristics of SAW PH2 were better than those of SAW PH1.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.6
• /
• pp.455-465
• /
• 2017

To figure out the weldability and welded joint performance on the FCAW of SM490TMC 120mm, several specimens were manufactured and 10 kinds of experiments were implemented. The result of the weld zone chemical composition test, weld metal tensile test, weld zone tensile test, and weld zone impact test has satisfied the KS. Especially, the weld zone tensile test result shows the base metal fracture, which means the weld zone performs enough required performance. In addition, the results of the weld zone bending test, hardness test, macroscopic test, microscopic test, and the maximum hardness in HAZ were showing that the FCAW weld zone has fine quality.

• Computational Structural Engineering
• /
• v.6 no.3
• /
• pp.113-123
• /
• 1993

Most of the ship structures and offshore structures are constructed through the welding and they are always subjected to variable loads. In this study, fatigue and stress concentration of the various types of welding connections due to the variable loads are investigated by using numerical approach, and comparisons between numerical analysis and experiments are performed. Fillet weld, full penetration weld and partial penetration weld characteristics are studied by using parameters such as penetration length, welding leg length, size and penetration angle. Based on this study, it is suggested that the fillet welding can be replaced with the penetration welding in some cases. The results of this study can be used as guidelines for actual welding problems in the shipyards.

• Journal of Korean Society of Steel Construction
• /
• v.28 no.4
• /
• pp.281-292
• /
• 2016

In this research, 10 specimens of FCAW welding with positions of 1G and 3G were tested to confirm the weldability, welding positions, and welded joint performance of 60mm HSA800 steel. The test results showed that FCAW 1G and 3G satisfied HSA800 steel's KS and the criteria for homogeneity of strength, indicating a good weld zones. However, according to the tensile test results of weld zone, 3G position FCAW welding requires improvement of welding techniques and methods.

• Journal of Welding and Joining
• /
• v.3 no.2
• /
• pp.64-73
• /
• 1985

X선응력측정법은 결정의 각자간 거리를 표점으로 하는 각자변형도를 X선회절현상을 이용하여 직접규정하여 응력을 구하는 것이다. 따라서 비교재의 교정곡선으로 부터 간접적으로 응력을 측 정하는 자기법이나 초음파법 등의 비파괴측정법에 비하여 X 선응력측정법은 잔류응력과 같은 내부응력의 비파괴측정법에 알맞고 지금까지 많은 연구자에 의하여 용접부에 적용시키기 위한 시도가 행해졌었다. 앞서 말한 국제회의에서도 X선응력측정법을 취급한 논문이 6편이고 그 가운 데서 3편이 용접구조물 또는 이음부에 이 방법을 적용한 것이다. 그래서 본고에서는 먼저 용접 잔류응력의 발생기구와 계산법, 측정법에 대하여 기술하겠다. 똔 잔류응력이 용접이음부의 파괴 강도 및 용접균열에 미치는 영향, 용접잔류응력의 대책과 이용법에 대하여 일본에서의 연구를 중심으로 소개하겠다.

• Proceedings of the KWS Conference
• /
• 1993.05a
• /
• pp.32-35
• /
• 1993