• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.4
• /
• pp.464-471
• /
• 2002

Porosity formation in partial penetration welds by high power lasers is a serious problem in industry. There are two main causes that induce porosity formation. One form of porosity is due to gases (e.g. hydrogen, oxygen) dissolving into the weld pool because of the high temperature and then the rapid solidification traps gases as a bubble in the weld metal. The second problem is voids formed by the keyhole collapsing due to unstable keyhole fluid dynamics. The voids that form at the bottom of the keyhole are relatively large and irregular in shape compared to the gas bubbles; this void formation is the primary concern in this paper. The reduction of voids formed by keyhole collapse is achieved by improving the stability of keyhole. Two methods to improve keyhole stability are discussed in this paper: pulse modulation and beam incident angle. Pulse modulation of the laser beam was performed between 100 Hz and 500 Hz to find out the optimum frequency for the keyhole dynamics. The incident beam angle changed the impact angle of the laser beam to the work surface in a range of 0 to 25 degrees. Glycerin in a semi-solidified state is used as a medium for performing the welding because its transparency allows of visualization of the keyhole.

• Journal of Welding and Joining
• /
• v.21 no.1
• /
• pp.72-79
• /
• 2003

Fatigue behaviour of partially penetrated butt-welded joints in high strength steel plates, in which crack-like structural defect, i.e. lack of penetration(LOP), is inevitably introduced during welding processes, was investigated. Fatigue lives of two types of welded joints, namely X-grooved and K-grooved joints, were experimentally determined first. Observed fatigue crack propagation behaviours of the partially penetrated butt-welds were interpreted through considering 3-dimensional semi-elliptical crack shape in front of the LOP. Based on such interpretation, a fracture mechanical method to estimate stress intensity factors at the crack tip was proposed. Since the fatigue lift of the partially penetrated butt-welds was strongly influenced by the ratio of size of the LOP to thickness, D/t, the D/t was used as a main parameter to calculate the fatigue lift by using the proposed method. Comparison of the fatigue lift obtained experimentally and analytically agreed well with each other. Hence it is suggested that the method used in this work to predict fatigue lift of the partially penetrated butt-welds can be applied to real cases with improved lift-prediction capability.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.307-312
• /
• 2003

Joining thin aluminum alloy is difficult using most welding techniques. Many of problems associated burn-through by the high heat input. Common welding techniques are TIG, MIG, and MIG-PULSE welding. The VP-GMAW provides more control of the heat balance in the welding arc by taking advantage of the different arc characteristics obtained with each of the two polarities. In this paper, we proposed new VP-GMAW method by control DSP 320C32, and the characteristic and experiment result-voltage, current, welding bead, penetration by this method are presented.

• Journal of Welding and Joining
• /
• v.20 no.2
• /
• pp.95-101
• /
• 2002

After high power lasers are avaliable in the commercial market, the number of applications of the laser welding has been increased in manufacturing industries. Although the tailored blank laser welding of butt jointed steel sheets is well known recently in the automotive industries, the lap joint laser welding is a new technology to the automotive manufacturing people as well as the design people. But the deep penetration laser welding seems to be preferred to the partial penetration welding for the lap joint welding in the automotive manufacturers because the partial penetration is a serious deflect for the butt joint. In this study, the feasibility of partial penetration welding fur the lap joint $CO_2$ laser welding was studied fur the 1mm thick 390MPa high strength steel sheets for automotive bodies. The process window of the lap joint partial penetration welding was obtained from experiments with the gap size and the welding speed as process parameters. The partial penetration welding was found excellent on the basis of the tensile shear strength and sectional geometry. The bead width, input energy Per volume, tensile-shear strength, deformation energy and the sectional geometries after tensile-shear tests of partial penetration welded specimens are compared with those of full penetration welded specimens with a series of gaps and welding speeds.

• Journal of Welding and Joining
• /
• v.10 no.4
• /
• pp.222-229
• /
• 1992

A prediction of penetration and heat affected zone by using Finite Element Method in CO$_{2}$ Arc Welding has been discussed this paper. The temperature distribution of a base metal produced by the CO$_{2}$ arc welding processing is analyzed by using a three dimensional finite element model. The common finite element program ANSYS 4.4A was employed to obtain the numerical results. Temperature dependent material properties, effect of latent heat, and the convective boundary conditions are included in the model. Numerically predicted sizes of the penetration and the heat affected zone are compared with the experimentally observed values. As a result, there was a slight difference between numerical analysis values and experimentally observed values. For in the case of heat affected zone, it was not considered a precise forced convective coefficient value, and in the case of penetration, it was not, considered a arc force.

• Journal of Welding and Joining
• /
• v.27 no.2
• /
• pp.44-50
• /
• 2009

The characteristics of arc pressure, current density and heat flux distribution are important factors in understanding physical arc phenomena, which will have a marked effect on the penetration, size and shape of a weld in TIG welding. The purpose of this study is to find out the effect of the heat flux on the melting efficiency and penetration shape in TIG welding using the results of the previous investigators. The conclusions obtained permit to draw a proper method which derived the heat flux distributions by arc pressure distribution measurements, but previous researchers calculated heat flux and current distribution with the heat intensity measurements by the calorimetry. Heat flux of Ar gas arc was concentrated at the central part and distributed low from the arc axis to the radial direction, that of He mixing arc was lower than that of Ar gas, and it was wide distributed to radial direction. That showed a similar characteristic with the Nestor's by calorimetry calculated values. Throughout heat flux drawn in this study was discussed melting efficiency and penetration shape on Ar gas and He mixing gas arc.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.4
• /
• pp.53-58
• /
• 2010

Offshore floater such as FPSO, drillship is composed of topside and hull side, and the interface structure is called topside module support. In this study, practical considerations were investigated for the design of topside module supports, from the concept design stage to the final stage of structural determination, in view of design efficiency and construction productivity. The effects of welding design factors of topside module support, such as welding throat thickness, sectional welding area, and welding man-hours, were compared and analyzed closely with respect to productivity. The current status and problems regarding the application of deep or full penetration welding are discussed, and a direct-calculation method is suggested as a possible solution to these problems.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.4
• /
• pp.79-86
• /
• 2007

The shape of excessive penetration mainly depends on welding conditions(welding current and welding voltage), and welding process(groove gap and welding speed). These conditions are the major affecting factors to width and height of back bead. In this paper, back-bead prediction and weldability estimation using artificial neural network were investigated. Results are as follows. 1) If groove gap, welding current, welding voltage and welding speed will be previously determined as a welding condition, width and height of back bead can be predicted by artificial neural network system without experimental measurement. 2) From the result applied to three weld quality levels(ISO 5817), both experimented measurement using vision sensor and predicted mean values by artificial neural network showed good agreement. 3) The width and height of back bead are proportional to groove gap, welding current and welding voltage, but welding speed. is not.

• Journal of Welding and Joining
• /
• v.19 no.6
• /
• pp.636-642
• /
• 2001

Partial penetration welding joint defines the groove welds that applies the one side welding which does not use steel backing and both side welding without back gouging, that is, the partial penetration welding joint leaves an unwelded portion at the root of the welding area. In this study, we analyzed the residual stress and fracture on the thick metal plates that introduced the partial penetration welding method. As results of using above mentioned welding method, we could draw a conclusion that longitudinal stress and traverse stress occurred around the welding area was so minimal and did not affect any influence. We also performed the fracture behavior evaluation on the partial penetration multi-pass welding with 25.4mm thick plate by using theJ-integral, which finally led us the conclusion that the partial penetration multi -pass welding method is more applicable and effective in handling the root face with less than 6.35mm.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.112-112
• /
• 2009

레이저 용접은 아크 용접에 비해 상대적으로 빠른 용접과 깊은 용입이 가능하며, 낮은 열입력을 가지는 장점이 있다. 하지만 알루미늄 합금 용접 시 균열 감수성의 증가 및 용접강도가 저하되는 단점을 가지고 있다. 이러한 단점을 극복하는 방법으로 모재의 화학조성을 제어하는 방법과 부가적인 용접와이어를 공급하는 방법이 제안되었으나 레이저 용접에 적용하기 쉽지 않다. 아크 용접과 전자빔 용접에서는 열원에 오실레이션을 적용하여 결정립 구조를 제어하여 용접강도를 증가하는 방법이 제안되었다. 따라서 본 연구에서는 알루미늄 합금 5J32-T4의 용접균열 저감 및 용접강도 향상을 위해 레이저 위빙을 적용하였다. 1mm 두께의 알루미늄 5J32-T4를 사용하였으며, 4kW급 디스크 레이저와 레이저용 스케너를 이용하여 레이저 위빙을 구현하였다. 고온균열을 평가하기 위해 자기구속형 균열 평가방법을 사용하였으며, 용접강도를 평가하기 위해 겹치기 용접을 수행한 시편을 이용하였다. 고온균열 실험결과 레이저 위빙 적용 시 직선 용접에 비해 균열 감수성이 감소한 것을 확인하였다. 전단인장강도 측정결과 레이저 위빙의 적용에 따라 직선 용접에 비해 높은 전단인장강도의 확보가 가능하였다.