• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.2
• /
• pp.170-179
• /
• 2005

Electrolyte loss is considered as one of the major obstacles limiting the life time of molten carbonate fuel cells (MCFCs). Unit cells with an effective area of 100 $cm^2$ were prepared and were operated to determine the optimum matrix thickness which contains the maximum amount of electrolyte without serious preformance loss caused by high resistance. Matrices with different thickness, 1.45, 1.8, and 2.3 mm, were used in unit cells and those cells were operared about 5000, 10000, and 4000 hrs. The unit cell used 1.8 mm thick matrix showed 0.85 V (at 150 mA/$cm^2$) as the intial performance and this cell voltage is not lower than the cell voltage obtained in the cell with 1 mm thick matrix. This cell was operated for 10000 hrs. The cell used 1.45 mm thick matrices showed 16.6 % in the electrolyte loss after 5000 hr operation. In the case of the cell with 2.3 mm thick matrix, the initial cell voltage was below 0.80 V (at 150 mA/$cm^2$). For thermal cycle test, the gas crossover amount of unit cell used 1.8 mm thick matrix was much less than that of the cell with 1.0 mm thick matrix.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.1
• /
• pp.64-70
• /
• 2018

In this study, the kg-class Ni-Al alloy fabrication process at low temperature was developed from the physical mixture of Ni and Al powders. The AlCl3 as an activator was used to reduce the temperature of alloy synthesis below the melting temperature of Ni and Al elements (<$500^{\circ}C$). Mixed phase of Ni3Al intermetallic and Ni-Al solid-solution were identified in the XRD pattern analysis. Furthermore, from the analysis of SEM and particle size analyzer, we found that the particle size of synthesized alloy powders was not changed compared to the initial size of Ni particle after the formation of alloy powder at $500^{\circ}C$. In the creep test, the anode (which was fabricated by the prepared Ni-Al alloy powders in this study) displayed the enhanced creep resistance compared to the conventional anode.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.5
• /
• pp.413-420
• /
• 2013

Effect of inherent volatile matters in fuels on electrochemical reactions of anode was investigated for a single direct carbon fuel cell (DCFC). Raw coals used as power source in the DCFC release light gases into the atmosphere under the operating temperature of DCFC ($700^{\circ}C$) by thermal decomposition and only char remained. These exhausted gases change the gas composition around anode and affect the electrochemical oxidation reaction of system. To investigate the effect of produced gases, comparative study was conducted between Indonesian sub-bituminous coal and its char obtained through thermal treatment, carbonizing. Maximum power density of raw coal ($52mW/cm^2$) was appeared higher than that of char ($37mW/cm^2$) because the gases produced from the raw coal during thermal decomposition gave additional positive results to electrochemical reaction of the system. The produced gases from coals were analyzed using TGA and FT-IR. The influence of volatile matters on anodic electrolyteelectrode interface was observed by the equivalent circuit induced from fitting of impedance spectroscopy data.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.2
• /
• pp.107-118
• /
• 1999

A 5-kW MCFC stack with $3,000cm^2$ electrode area was tested to investigate cell performance and operation characteristics. The stack performance was evaluated based on electrical output and I-V change. The stack showed high cell performance (7.6 kW) than the design performance and operated for more than 5,760 hours, but a significant temperature gradient inside the stack was observed. A 3-dimensional mathematical model for molten carbonate fuel cell (MCFC) was developed for the purpose of simulation of stack performance during the operation. The model was solved using PHOENICS, a computational fluid dynamics (CFD) code. The simulation result demonstrated a close prediction of the temperature gradient and stack performance.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.6
• /
• pp.800-809
• /
• 2011

The reaction characteristics of an integrated reactor with steam reformer and catalytic combustor using anode offgas for high temperature fuel cells such as MCFC and SOFC have been experimentally investigated in the present study. The coupled reactor had a coaxial cylindrical shape, and the inner and the outer tube was packed with combustion catalysts and reforming catalysts, respectively. Thus, the endothermic steam reforming could proceed by absorbing heat from catalytic combustion of anode offgas. Results show that increasing inlet temperature and decreasing excess air ratio increased the reformer temperature, which led to the increase in $H_2$ yield. The reforming performance for SOFC conditions was better than that for MCFC conditions since the composition of flammable components became smaller for MCFC cases. Measured reformate composition under various test conditions correlated well with thermal equilibrium composition.

• Clean Technology
• /
• v.20 no.1
• /
• pp.88-94
• /
• 2014

During the past decades much attention has been paid to the desulfurization of diesel oil which is important as a source for the fuel cells to prevent the sulfur poisoning of both diesel steam reforming catalyst and electrode of fuel cell. Although alternative desulfurization techniques have been investigated, desulfurization for ultra-low sulfur diesel (ULSD) is still challenged. Therefore, this research focuses on the desulfurization of commercial ULSD for the application to molten carbonate fuel cell (MCFC). Herein, the performances of several kinds of commercial adsorbents based on activated carbons, zeolites, and metal oxides for desulfurization of ULSD were screened. The results showed that metal oxides based materials can feasibly reduce sulfur concentration in ULSD to a level of 0.1 ppmw while activated carbons and zeolites did not reach this level at current conditions.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3049-3052
• /
• 2008

MCFC(molten carbonate fuel cell) power generation system is prime candidate for the utilization of fossil based fuels to generate ultra clean power with a high efficiency. In the MCFC power plant system, a combustor performs a role to supply high temperature mixture gases for cathode and heat for reformer by using the stack off-gas of the anode which includes a high concentration of $H_2O$ and $CO_2$. Since a combustor needs to be operated in a very lean condition and to avoid excessive local heating, catalytic combustor is usually used. The catalytic combustion is accomplished by the catalytic chemical reaction between fuel and oxidizer at catalyst surface, different from conventional combustion. In this study, a mathematical model for the prediction of internal flow and catalytic combustion characteristics in the catalytic combustor adopted in the MCFC power plant system is suggested by using the numerical methods. The numerical simulation models are then implemented into the commercial CFD code. After verifying result by comparing with the experimental data and calibrated kinetic parameters of catalytic combustion reaction, a numerical simulation is performed to investigate the variation of flow and combustion characteristics by changing such various parameters as inlet configuration and inlet temperature. The result show that the catalytic combustion can be effectively improved for most of the case by using the perforated plate and subsequent stable catalytic combustion is expected.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1350-1352
• /
• 2003

For developing a 100 kW MCFC power generation system, Several design parameters for a fuel cell stack and system analysis results by Cycle Tempo, a processing computer soft ware, were described. Approximately two substacks with 90 cells are required to generate 100 kW at a current density of $125\;mA/cm^2$ with $6000\;cm^2$ of cells. An overall heat balance was calculated to predict exit temperature. The 100 kW power is expected only under pressurized operation condition at 3 atm. Recycle of cathode gas by more than 50% is recommended to run the stack at $125\;mA/cm^2$ and 3 atm. Manifolds should be designed based on gas flow rates for the suggested operating condition. The fuel cell power generation system was designed conceptually with several choices of utilization of anode exhaust gas. To operate and evaluate the MCFC system, control and measurement system and operation mode are designed before 100 MCFC system construction. In system control schematics, OS, PLC and MMI were consisted and have roles for MCFC system control. For operation of 100 kW MCFC system, NS, PS PR mode were considerated step by step and simulated.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.3
• /
• pp.124-131
• /
• 2006

For commercialization of molten carbonate fuel cell (MCFC), it has some problems to be overcome such as decrease of porosity and thickness of the anode under the operating condition (at $650^{\circ}C$ and working pressure of more than 2 $kg_f/cm^2$). Recently, Ni-Al alloy anode has been proposed to replace the conventional Ni-Cr anode as an alternative material to resist a creep and inhibit the sintering. The objective of this research is to sinter the green sheet of Ni-Al alloy anode during single cell pre-treatment process, which has several advantages like cost down and simplification of manufacturing process. However, the Ni-Al alloy anode prepared with a conventional pre-treatment process showed the phase separation of Ni-Al alloy and formation of micropore(${\leqq}0.4{\mu}m$), resulting in low creep resistance and high electrolyte re-distribution. In order to prevent the Ni-Al alloy anode from phase-separating, nitrogen gas was used in the process of pre-treatment. Introducing the nitrogen, the phase separation from Ni-Al alloy into nickel and alumina was minimized and increased creep resistance. However, there was some micropore formation on the surface of Ni-Al alloy anode during the cell operation due to creation of lithium aluminate. Addition of more amount of electrolyte into a cell, especially at cathode, made the cell performance stable for 2,000 hrs. Consequently, it was possible to make the Ni-Al alloy anode with good creep resistance by the modified in-situ sintering technique.

• Proceedings of the Korea Technology Innovation Society Conference
• /
• 1998.05a
• /
• pp.10-10
• /
• 1998

생명공학의 혁신적 발명성을 매우 잘 보여주는 성공사례의 하나가 사람락토페린을 함유한 형질전환 젖소의 개발이다. 우유의 모유화를 내걸고 있는 본 연구는 국내·외에 막대한 잠재시장 규모가 예상되고 있다. 그러나 생명공학 제품은 ‘생물 재해(Bio Hazard)’에 대한 우려와 윤리문제를 제기할 수 있기 때문에 대중인식(Public Acceptance)에 대한 연구가 매우 중요한 의미를 가지는 것이다. 이러한 상황인식하에 사람락토페린을 함유한 유제품에 대한 소비자행태분석(Consumer Behavior Analysis)을 수행하게 되었다. 본 연구에 사용된 연구방법은 비시장가치평가법 중 임의가치평가법(CVM)을 사용하고 있다. 임의가치평가법은 선진국 특히 본 이론의 발상지인 미국에서 환경재기 가치를 측정하는 방법으로 사용되어 오고 있는데 이를 신상품 및 과학기술의 가치평가법으로 확대하여 연구하여온 필자의 일련의 연구중의 한 시도이다. 좋은 CVM 연구를 수행하기 위해서는 CVM이 요구하는 가치평가방법에 맞추어 설문서가 구성되고 분석되는 일이 무엇보다도 중요한 일이다. 본 연구에서는 CVM의 연구방법에 맞추어 사람락토페린 강화우유에 대한 소비자지불의향(Consumer Willingness to Pay) 조사와 더불어 사람락토페린 강화우유에다가 DHA, 칼슘 등 새로운 기능성 물질을 추가하여 더욱 좋은 기능을 첨가한 경우의 구입할 용의와 지불의향에 대한 조사를 수행하였다. 본 연구에서는 과학기술에 의해 탄생된 신상품에 대한 임의가치평가법의 적용이라는 새로운 시도의 연구라는점을 감안하여 본 연구를 바탕으로 더욱 새로운 문제제기와 추가적인 연구가 필요하다고 생각된다.적인 자세를 견지한다. 한편, 적응의 원리에 입각한 교육은 문화와 전통에 대한 피동적 전승을 넘어서 사회의 변화에 따라 교육체제와 내용을 바꾸는 등 적극적으로 변화에 대응하고, 이러한 변화를 주도할 인간육성에 힘을 기울이는 교육방식을 취한다. 시대적 변화의 소용돌이 속에서 교육은 이제 기왕의 많은 교육적 신화들을 타파하고 뉴 밀레니엄을 준비해야할 기로에 서 있다. 현재의 변화를 슬기롭게 대처하고 미래의 변화에 능동적으로 적응하는 인간을 육성하기 위한 오늘날 교육의 사명은 우선 미래사회를 위한 교육정책의 방향을 수립하는 일이다. 교육정책은 국가의 교육방침으로서 현실 교육문제의 해결도 중요하지만 미래의 발전을 기약할 수 있는 장기적인 비젼과 목표 속에서 정립될 필요가 있다. 이러한 의도하에 본 연구는 21세기를 대비한 교육정책의 방향을 탐색하고 그에 따른 정책적 과제를 제시하는 데 그 목적이 있다. 이러한 목적하에 본고는 \circled1 과거 우리 나라의 교육정책을 반성적으로 회고하고, \circled2 미래사회에 대한 전망과 교육적 시사점을 분석하며, \circled3 마지막으로 21세기의 변화에 적응하기 위한 교육정책의 방향과 과제를 내용으로 제시하고자 한다.탄산염으로의 전환이 진행되고 있다. 이러한 배경으로부터 Uchida그룹에서 개발한 FeiCr/AVTi재료와 현재 분리판 재료로 사용증인 SUS 310, S SUS 316재료에 대해. 산화성 분위기의 5기압까지의 가압하에서, Li-K, Li-Na탄산염에 대하여 부 식거동을 검토한 결과, 가압하에서 내식성이 향상되는 것이 발견되었다. 이유로서는 가압하에서 용융탄산엽의 증가된 산화력으로 보다 치밀한 내식성 산화물 피막