• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.5
• /
• pp.197-202
• /
• 2021

Synthesis of Z-type hexaferrite Ba₃Co₂Fe₂₄O₄₁ (Ba₃Z) and Ba_1.5La_1.5Co₂Fe₂₄O₄₁ (Ba_1.5La_1.5Z) powders were tried using molten salt synthesis after primary calcination. Ba₃Z calcined at 1000℃ was formed with both M-type and Y-type hexaferrite, and then Z-type was obtained when sintered with molten salt at 1150℃ and 1200℃. In the case of Ba_1.5La_1.5Z calcined at 1000℃, however, M-type hexaferrite, CoFe₂O₄ (Spinel phase), and LaFeO₃ were synthesized. As a result, Z-type hexaferrite was not synthesized after sintering with molten salt. In addition, the aspect ratio of the particles decreased as the sintering temperature increased with molten salt synthesis. To obtain a single-phase Ba_1.5La_1.5Z with a high aspect ratio, it is expected the raw materials have to calcine below the temperature of a spinel phase formation before sintering with molten salt.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2008.05a
• /
• pp.237-237
• /
• 2008

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2009.11a
• /
• pp.345-345
• /
• 2009

전기화학적 환원 기술을 이용한 고온 용융염 전해환원의 결과 생산되는 금속전환체는 다공성 특성에 의해 전해환원의 매질인 용융염을 함유하게 된다. 전해환원과 후속 전기화학 공정인 전해정련의 전해질은 각각 LiCl과 LiCl-KCl 공융염으로 상이하기 때문에 이렇게 금속전환체에 포함된 LiCl 염이 동반되어 전해정련 공정에 도입될 경우 전해정련 공정의 공융염 조성을 어긋나게 한다. 이에 따라 금속전환체의 잔류염은 효과적으로 제거되어야 하며 공정으로 감압 증류에 의한 잔류염 제거 공정이 고려되고 있다. LiCl은 증기압이 비교적 낮기 때문에 감압의 고온 조건이 공정에 필요하다. 그러나 상평형도 분석 결과 전해환원 공정에서 산화물을 담아 음극으로 사용되어 환원된 금속전환체와 함께 도입되는 SUS 재질의 바스켓과 사용후핵연료 금속전환체의 주된 원소인 우라늄과는 공융할 수 있기 때문에 LiCl 증발 온도는 $720^{\circ}C$ 이하로 유지되어야 한다. 이와 같은 조건에서 LiCl 증발 속도를 높이기 위해서는 감압 조건이 필수적이다. 본 연구에서는 감압조건에서 LiCl 휘발 실험을 위해 폐쇄형 및 개방형 반응기를 제작하여 압력 조건 및 Ar 유량 등에 따른 LiCl 휘발율을 측정하였다. 증발된 LiCl은 일정 감압 조건에서 분말형으로 냉각부위에 회수 될 수 있었으나 완전 진공 조건에서는 결정형으로 냉각 부위에 응축되는 것으로 확인 되었으며 일정 진공 조건에서는 Ar 유량에 따라 증발량이 의존하지 않는 것으로 나타났다. 연구 결과 증발염의 취급 빛 이송을 위해 분말형 회수를 목표로 설정할 수 있었으며 공정조건으로 일정 수준의 감압 조건을 제시하였다. 이 후 후속 연구로 장치의 대형화 및 증발 속도 향상을 위한 추가적인 연구가 계획되어 있으며 연구 결과에 기초하여 공학규모 파이로 공정 시설인 PRIDE에 도입될 장치의 기초 설계 자료를 생산할 예정이다.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.41-48
• /
• 2010

Uranium deposits from an electrorefining process contain about 30% salt. In order to recover pure uranium and transform it into an ingot, the salts have to be removed from the uranium deposits. Major process variables for the salt distillation process of the uranium deposits are hold temperature and vacuum pressure. Effects of the variables on the salt removal efficiency were studied in the previous study[1]. By applying the Hertz-Langmuir relation to the salt evaporation of the uranium deposits, the evaporation coefficients were obtained at the various conditions. The operational conditions for achieving above 99% salt removal were deduced. The salt distilled uranium deposits tend to form the eutectic melt with iron, nickel, chromium for structural material of salt evaporator. In this study, we investigated the hold temperature limitation in order to prevent the formation of the eutetic melt between urnaium and other metals. The reactions between the uranium metal and stainless steel were tested at various conditions. And for enhancing the evaporation rate of the salt and the efficient recovery of the distilled salt, the thermal analysis of the salt distiller was conducted by using commercial CFX software. From the thermal analysis, the effect of Ar gas flow on the evaporation of the salt was studied.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.4
• /
• pp.156-160
• /
• 2015

Experiments using a metal oxide of a non-nuclear material as a fuel are very useful to develop a new electrolytic reducer for pyroprocessing. In this study, the titanium oxides (TiO and $TiO_2$) were selected and investigated as the non-nuclear fuel for the electrolytic reduction. The immersion tests of TiO and $TiO_2$ in a molten 1.0 wt.% $Li_2O$-LiCl salt revealed that they have solubility of 156 and 2100 ppm, respectively. Then, the Ti metals were successfully produced after the separate electrolytic reduction of TiO and $TiO_2$ in a molten 1.0 wt.% $Li_2O$-LiCl salt. However, Ti was detected on the platinum anode used for the electrolytic reduction of $TiO_2$ unlike TiO due to the dissolution of $TiO_2$ into the salt.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.2
• /
• pp.121-128
• /
• 2014

This study aims to develop a simulation bed for the mechanical balance of plants of high temperature fuel cells such as molten carbonate fuel cells. For using fuel cells in transportation, the optimization of the balance of plants should be considered. In this study, the dynamic model of a molten carbonate fuel cell and the model's responses to inlet gas composition, pressure, flow rate, and stack temperature were analyzed. On/off simulation was performed for testing the dynamic model's feasibility. The simulation results are in reasonable agreement with the experimental results from published literatures.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2007.11a
• /
• pp.295-296
• /
• 2007

• Journal of the Korean Electrochemical Society
• /
• v.5 no.2
• /
• pp.62-67
• /
• 2002

The corrosion of the metallic cell components is blown to be one of the major reason f3r the performance degradation and subsequently the life-time limitation of the MCFC. To elucidate the corrosion phenomena, a corrosion study with the AISI-type 316L stainless steel, the most widely used separator material, in 621Li/38K carbonate eutectic melt was carried out. Corrosion phenomena in an MCFC were observed to differ from one location to another due to different environmental condition. The stability of passive film was found to be responsible fur the variations in corrosion phenomena. According to the potentiodynamic analysis, the passive film formed in anode-gas environment was less stable than in cathode-gas environment. The potentiostatic method combined with XRD analysis in addition to the cyclicvoltammetry was conducted to get an insight on variety corrosion reaction of AISI-type 316L stainless steel in a carbonate melt.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.256-260
• /
• 2005

마그네슘은 자동차 엔진 경량화재료, 휴대폰케이스 등 기능성 경량재료로서의 용도개발과 함께 수요가 증가하고 있다. 마그네슘 제련법은 원료광의 특성에 따라 달라지는데 크게 용융염전해법과 열환원법 두 가지로 구분할 수 있다. 본 연구에서는 염화마그네슘을 사용하여 용융염전해법에 의해 전해 마그네슘을 얻고자 하였다. 전해전압 7V로 일정한 전극침지 깊이에서 두 가지 염욕을 비교 실험하였으며, $KCl/NaCl/MgCl_2$ 혼합 염욕을 $760^{\circ}C$에서 전해한 결과 약 47%의 전류효율을 달성할 수 있었다. 회수된 전해 마그네슘의 순도는 98% 이상이었다. 본 연구를 통하여 용융염 전해장치를 스케일엎하거나 상용화시에 장치설계 등에 필요한 기초 자료들을 축적할 수 있었다.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.368-372
• /
• 2003

The present study focused on obtaining the optimum conditions for depositing pure uranium onto a solid cathode. As for the results of the experiments, it was conformed that when the concentration of $UCl_3$ in the molten salt(LiCl-KCl) is more than 2wt%, pure uranium could be deposited onto a solid cathode, In addition. the effect of both the current density and the U contents in the molten salt or th ratio of uranium to salt was examined and the uranium morphology was also investigated.