• Proceedings of the Korea Information Processing Society Conference
• /
• 2012.11a
• /
• pp.1252-1255
• /
• 2012

CRDI 디젤엔진을 산업용 엔진에 적용하여 최근 강화된 국내외의 배출가스 규제 조건을 충족시키기 위해 사용자가 연료의 분사시기와 분사량을 조절할 수 있는 CRDI ECU 제어 알고리즘을 개발하였다. CRDI 엔진 제어 ECU의 입력 요소 중 CKP와 CMP 센서를 이용하여 디젤 노킹 및 롱투스를 판별하는 알고리즘을 개발하여 분사시기와 분사량의 조절 시점을 결정하고, 엔진의 이상 유무를 판별할 수 있는 알고리즘을 개발하여 엔진의 밸런스를 조절함으로써 연비 향상 및 유해가스 저감을 효율적으로 개선할 수 있도록 하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.353-355
• /
• 2008

최근 석탄 가스화 기술은 화석연료인 석탄을 기존의 공해물질 발생을 90%이상 줄이면서 고효율로 활용할 수 있는 방법으로 각광받고 있다. 본 연구는 습식 석탄 가스화기에서 가스화의 핵심적인 요소인 버너의 분무 관계 분야에 대한 분무 특성 및 무화성능을 높일 수 있는 분무기의 구조 및 운전 조건 등을 제시 할 목적으로 분무 시 내부를 관찰 할 수 있는 아크릴을 이용하여 내부 혼합식 버너를 제작하였다. 미립화 특성을 파악하기 위하여 $O_2$/Fuel Ratio 및 버너의 내부 혼합 방식, 분사각도, 각 분사 높이에 따른 미립화 특성을 관찰하였으며, 입도 분석은 심파텍사의 입도 분석기를 이용하여 측정하였다. 내부 혼합식 버너의 입도는 분사 각도와 $O_2$/Fuel Ratio에 따라서 변화하는 경향을 나타냈으며, 공급되어지는 Fuel은 석탄 슬러리와 물을 이용하여 각각의 입도를 측정하였다. slurry의 공급량이 고정된 상태에서 산소 공급량이 증가함에 따라 미립화도는 증가하는 경향을 나타내었으며, 슬러리 공급량과 산소 공급량이 동일한 경우 버너의 분사 각도에 따라 미립화도가 다르게 나타나는 특성을 관찰하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.6
• /
• pp.645-653
• /
• 2005

The effects of a WI(Water Injection) at the intake Pipe and an urea injection at the exhaust pipe for a 4-cylinder DI(Direct Injection) diesel engine were investigated experimentally The water quantity was controlled by temperature of intake manifold and MAF(Manifold Air Flow). In addition, the urea quantify was controlled by NOx quantify and MAF. Effects of WI system, urea-SCR system and tandem system were investigated for with and without EGR(Exhaust Gas Recirculation). As the results. the SUF(Stoichiometric Urea Flow) and NOx map were obtained. In addition, NOx results can be visualized with engine speed and engine load. It was concluded. therefore, that the NOx reduction effects of the tandem system without the EGR were more than those with the EGR base engine.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.331-332
• /
• 2006

연료 분사펌프는 600bar 이상의 고압 연료를 분사밸브를 통하여 디젤기관의 연소실에 연속적으로 공급하는 장치이며, PLUNGER&BARREL 은 분사펌프의 핵심 부품으로 작동하고 고온 고압의 환경에서 $4{\mu}m$ 미만의 초정밀 간극을 유지해야 한다. 이러한 정밀한 가공 상태를 유지하기 위해선 내마모성 및 내열성에 적합한 재료와 열처리가 필수 요소이다. 현재 주로 사용되고 있는 방식은 DIAMOND STONE 에 의한 HORNIG 가공을 주로 사용하기 있다. 하지만, 연삭 가공과는 달리 별도의 치수 보정 장치가 없는 관계로, STONE 마모와 그에 따르는 마모량 공차에 의한 정밀 치수 확보의 어려움으로 인해, 고비용 저효율의 약점을 가지고 있다. 그러므로 기존의 HORNING STONE 방식을 대체한 PIN 방식의 HORNING MACHINE 개발을 목표로 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.4
• /
• pp.63-74
• /
• 1989

It is well-known that the fuel injection system if a diesel engine has taken a more important place in understanding of diesel combustion process with combustion chamber. But a diesel fuel injection system has an assembly of many complex and intricate problems such as the desired rate of injection, secondary injection and injection pump etc., in addition to the atomization for ignition and combustion, the penetration and diestribution for proper utilization of air. The analysis is carried out by simplifing and modeling the injection phenomena and dividing into three parts comprising of fuel injection pump, high pressure pipe and fuel injection nozzle. The purpose of this paper is to describe an analytical simulation of the injection system and to speed up the work of developing injection systems for new engines. The effects of important injection parameters as predicted by the present model are found to be in good agreement with experiment. It can be seen that there is an optimal pipe diameter for maximum quantity injected.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.6
• /
• pp.397-407
• /
• 2017

In this study, a SCR system is employed to selectively reduce $NO_X$, which is a major cause of environmental pollution and issues in diesel engines. In particular, this paper focuses on the combination of feedforward injection strategies, depending on the NO/$NO_X$ ratio, and feedback injection control, using $NH_3$ coverage ratio, based on a SCR model. A 2.2 L passenger diesel engine, which is equipped with a diesel oxidation catalyst (DOC) and a diesel particle filter (DPF), was used in the experiments. The developed control algorithm is implemented on a real-time computer with injection control algorithm. By analyzing the $NO_X$ emission measurement, the performance of the proposed injection control algorithm is verified.

• Journal of Oral Medicine and Pain
• /
• v.30 no.3
• /
• pp.375-381
• /
• 2005

Er:YAG laser has been considered a promising alternative to dental drill and many researches indicate that adjustment to variable parameters, including water flow rate, pulse energy and pulse repetition rate, can be made to improve ablation ability and efficiency of the laser. Of these parameters, addition of water spray during irradiation has been thought to ablate dental hard tissue more rapidly and safely. The purpose of this study was to investigate tooth ablation amount by Er:YAG laser irradiation as related to varied water flow rates added and, ultimately to find the most effective water flow rate for ablation. In addition, the temperature change of pulp chamber during irradiation was also monitored on the irradiated and opposite pulpal walls, respectively. An Er:YAG laser with contact mode was employed. Extracted human molars were split into two pieces for ablation experiment. Pulse energies of 200 and 300 mJ with a pulse repetition rate of 20 Hz and 5 water flow rates (1.6, 3.0, 5.0, 7.0, and 10.0 ml/min) were applied. Each irradiation was performed for 3 seconds. According to these parameters, experimental groups were divided into 10 subgroups which consisted of 5 specimens. For temperature experiment, another 5 tooth-specimens were prepared in the manner that pulp chamber was open through access cavity preparation and two temperature-measuring probes were placed respectively on the irradiated and the opposite walls of pulp chamber. From the experiment on ablation amount related to different water flow rates, it was shown that the least water flow rate of 1.6 ml/min ablated more than any other water flow rates (p<0.000). When the irradiation for 3 seconds, combined with the pulse repetition time of 20Hz and the water flow rate of 1.6 ml/min was done to tooth specimen, the temperature rise was not noticeable both on the irradiated and the opposite pulpal walls (less than 3$^{\circ}C$) and there was no significant difference in temperature rise between the two pulse energies, 200 and 300 mJ. From the results of this study, it is suggested that tooth ablation with Er:YAG laser can be done effectively and safely at a energy between 200 and 300 mJ/pulse and a pulse repetition rate of 20 Hz when the lasing is conjugated with the water flow rate of 1.6ml/min.

• Journal of Navigation and Port Research
• /
• v.40 no.4
• /
• pp.173-181
• /
• 2016

From 2016, controls on reduction of NOx and SOx emissions from the vessels that are operated in the emission control area were tightened. The selectivity catalytic reduction system of the denitrification equipment which NOx among the above controlled materials is very effective and used commercially very much. But it has the disadvantage that CSR is activated at high temperatures. Therefore, the SCR and SCR activation instrument that can react even at low temperatures by using micro-nano bubbles so that the above problems can be minimized were developed. And the computational fluid dynamics technique was used by ANSYS-CFX package to prepare the plan that improves the SCR system's efficiency. Simulation for the viscous flow analysis of the SCR system was executed by applying the Navier-Stokes equation to it as a governing equation. For the SCR system's shape, 3D modeling was done by using CATIA V5. SCR jet nozzle's position was checked by changing it to the intervals of 1/3, 1/2, and 2/3 from the inlet of the vent pipe to compare the SCR system's efficiency. And the number of nozzles was compared and analyzed by simulating 4, 6, and 8 holes to check an effect of the number on the SCR system's efficiency. The simulation result has found that the closer nozzles are to the inlet of the vent pipe and the more nozzles are, the more efficiency is improved.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.57-63
• /
• 2005

The effects of an urea injection at the exhaust pipe for a 4-cylinder DI(Direct Injection) diesel engine were investigated with the parameters such as urea-SCR(Selective Catalytic Reduction) and EGR system. The urea quantity was controlled by NOx quantity and MAF(Manifold Air Flow). The urea injection quantity can be controlled with the urea syringe pump, precisely. The effects of NOx reduction for the urea-SCR system were investigated with and without ECR engine, respectively. It was concluded that the SUF(Stoichiometric Urea Flow) is calculated and the NOx results are visualized with engine speed and load. Furthermore, the NOx map is made from this experimental results. It was suggested, therefore, that NOx reduction effects of the urea-SCR system without the EGR engine were better than that with the EGR engine except of low load and low speed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.11
• /
• pp.999-1004
• /
• 2010

Recently, many technologies have been developed in order to satisfy stringent emission regulations. However, in the case of diesel engines, the stringent emission regulations with respect to NOx and PM have not yet been satisfied. A dramatic reduction in the NOx and PM emissions could be achieved by using after-treatment systems such as lean NOx trap (LNT) and urea-SCR systems. However, the high temperature in the exhaust pipe affects the spray behavior of the secondary injector, which is used for supplying the Urea-SCR. Because of this high temperature, it is difficult to achieve uniform distribution of the reducing agent in the manifold. In this paper, the characteristics of a urea-SCR injector used for injecting in the exhaust pipe are presented. The purpose of this study was to investigate the spray characteristics of the injector, such as the spray angle, injection quantity, and SMD. In addition, laser diagnostics and high-speed-camera images were used to analyze the injector spray characteristics and to present a distribution of reduction in the transparent manifold.