• Journal of the Korean Geotechnical Society
• /
• v.27 no.1
• /
• pp.5-16
• /
• 2011

This paper presents the results of a three-dimensional finite element analysis on load supporting mechanism of pile constructed above underground cavity in limestone rock formation. Considering a wide range of cavity conditions, the behavior of pile was studied using the bearing capacity, rock yielding pattern, stress distribution and deformation of pile head and the cavity. The results indicate that the load transfer mechanism of pile, rock yielding pattern and the reduction of bearing capacity of pile significantly vary with the location, size and length of cavity. Based on the results, graphical solutions defining the reduction of the bearing capacity with specific cavity conditions were suggested.

• Proceedings of the Korean Information Science Society Conference
• /
• 2005.07a
• /
• pp.358-360
• /
• 2005

스무딩은 가변 비트율로 저장된 비디오 데이터를 클라이언트로 전송할 때 일련의 고정 비트율로 전송할 수 있도록 전송 계획을 세우는 것이다. 이러한 스무딩 알고리즘들 중에서 e-PCRTT 알고리즘은 전송률 변화 횟수가 주어지고 구간의 크기가 고정이어서 전송률 변화 횟수, 첨두 전송률, 버퍼 이용률 등의 평가 요소들이 증가될 수 있다. 이러한 문제점을 개선하기 위해 전송률 변화 횟수의 제한이 없고 구간의 크기가 가변적인 EBA(Enhanced Bandwidth Allocation)[9,10] 스무딩 알고리즘을 제안한 바 있다. 그러나 이 방법에서는 전송률의 증가 또는 감소를 고려하지 않고 전송률을 변화시키기 때문에 이전 구간의 전송률에 비해 급격하게 높은 전송률이 요구될 수 있으며 증가되는 전송률로 보내야 하는 프레임 개수가 많아질 수 있다. 이는 네트워크 자원의 효율적인 사용을 어렵게 할 수 있다. 따라서, 본 논문에서는 EBA 알고리즘을 개선하여 첨두 전송률과 증가되는 전송률로 보내야 되는 프레임 개수를 감소시키는 알고리즘을 제안한다. 제안된 알고리즘의 성능은 E.T 90의 비디오 소스를 가지고 EBA 알고리즘과 전송률 변화 횟수, 첨두 전송률, 증가되는 전송률로 보내야 하는 프레임 개수 등을 비교 분석하여 평가하였다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.12
• /
• pp.8-13
• /
• 2020

Seamless pipes are fabricated by drilling a hole in a cylindrical material and drawing the material to the desired diameter. These pipes are used in environments where high reliability is required. In this study, the pipe drawing process was simulated using DEFORM, a commercial finite element method (FEM) analysis program. The outer diameter of the steel cylinder used herein before drawing was 70 mm, and the target outer diameter was 58 mm. The drawing process consisted of two stages. In this study, the effect of cross-sectional reduction rate on the pipe was investigated by varying the cross-sectional reduction rate in each step to achieve the target outer diameter. The results of this study showed that the first section reduction rate of 26% and the second section reduction rate of 13.9% caused the lowest damage to the material. Moreover, the FEM simulation results confirmed the influence of the drawing die angle on the pipe drawing process. The drawing die angles of 15° in the first step and 9° in the second step caused the least damage to the material.

• The Journal of Engineering Geology
• /
• v.13 no.4
• /
• pp.405-418
• /
• 2003

Measurements of volumetric water content and saturation of porous media are very important factors in understanding the physical characteristics of soil, groundwater recharge by rainfall, pollutant movement, and slope failure. To measure such physical parameters, a permittivity method using electromagnetic wave is applied and use is made of the special permittivity response of understand to water and ethanol. In particular, the estimation is required because permittivity is influenced by the nature of the underground environment. In this study, we carried out experiments on the relative dependency of soil density, temperature and salinity of standard sand and granitic weathered soil using FDR-V system (Frequency domain reflectometry with vector network analyzer) within a frequency range of 1 - 18 GHz. The results of the study showed that the dielectric constants of standard sand and granitic weathered soil increased with increased volumetric water content of soil. However, the dependency of soil density was found to be a little low. Changes of dielectric constant with temperature appeared definitely in the real part of 1 GHz. That is, the dielectric constant of real part at 1 GHz of water and standard sand increased with the rise of temperature. However, ethanol showed decreased tendency. The study also showed that dielectric constant increased with increase in salinity at imaginary part of 1 GHz. It could be concluded from this study FDR-V system can adequately measure the physical properties of soil and the degree of salinity concentration of porous media within 1 GHz frequency range using dielectric constant.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.2
• /
• pp.71-79
• /
• 1997

In this paper, a codeword-dependent distance normalization(CDDN) and an instar-formed fuzzy smoothing of output distribution are proposed for robust estimation of output probabilities in the FVQ(fuzzy vector quantization)-DHMM(discrete hidden Markov model). The FVQ-DHMM is a variant of DHMM in which the state output probability is estimated by the sum oft he product of the output probability and its weighting factor for each codeword on an input vector. As the performance of the FVQ-DHMM is influenced by weighting factor and output distribution from a state, it is required to get a method to get robust estimation of weighting factors and output distribution for each state. From experimental results, the proposed CDDN method has reduced 24% of error rate over the conventional FVQ-DHMM, and also reduced 79% of error rate when the smoothing of output distribution is also applied to the computation of an output probability. These results indicate that the use of CDDN and the fuzzy smoothing of output distribution to the FVQ-DHMM lead to improved recognition, and therefore it may be used as an alternative to the robust estimation of output probabilities for HMMs.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2009.04a
• /
• pp.557-563
• /
• 2009

FMVSS 302 수평 연소 시험법을 통과한 자동차 내장재의 열적 특성을 평가하기 위해서 콘칼로미터를 이용하여 시험을 수행하였다. 화재 위험과 관련된 착화시간(time to ignition), 열방출률(heat release rate), 질량감소율(specific mass loss rate), 감쇠계수(extinction coefficient) 그리고 연기요소(smoke factor)와 같은 여러 가지 요소들을 분석하였다. 최대 열방출률값은 시험편에 따라 232${\sim}$635kW/$m^2$으로 큰 편차를 보였으며, 연기요소 또한 99${\sim}$551MW/$m^2$로 큰 편차를 보였다. 보조매트의 최대 열방출률은 다른 시험편에 비해서 상대적으로 낮은 값을 보였지만, 총연기 발생이 다른 시험편에 비해서 상당히 높았다. 따라서 최대 열방출률과 총 연기발생을 함께 고려한 연기요소값은 상대적으로 다른 시험편에 비해서 높게 나타났다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.26 no.2
• /
• pp.72-77
• /
• 1993

This study was conducted to evaluate coated urea complex fertilizer (CUC) application for rice growth and its grain quality on clay loam (Deogpyeong series) and sandy loam (Gangseo series) in southern region of Korea, 1992. The coated urea complex fertilizer used in the experiment was CUC I and II. The CUC I is a complex fertilizer consisting of 18-12-13 for $N-P_2O_5-K_2O$ including 50% of coated urea as nitrogen source, and CUC II is the same complex fertilize as mentioned above but it contains 25% of coated urea. Seventy percent of conventional fertilizer for nitrogen level was applied as basal dose of side-band placement (SBP) and whole plowlayer placement (WPP). Greenish degree of rice leaf color at the late growth stage was high in CUC plots regardless of application method and soil series. Amount of nitrogen uptaken by the rice plant at harvesting stage was mush more in the CUC treatment compared to convential fertilizer, and also much more in CUC I than that of CUC II. In the WPP on clay loam, harvest index of CUC treatment was showed very low level, which was reduced more in CUC II plot. In the CUC treatments, perfect rice grain ratio decreased remarkably, and the notched-belly rice kernel ratios among imperfect rice grain increased drastically. In rice grain, Hon-value(Mg to K.N ratio) decreased, protein and amylose contents increased in CUC application plots in WPP. In addition, gel consitency and alkali spreading value related to eating quality in CUC plots were getting longer and lower, respectively. The yield in CUC plot was similar to conventional fertilizing, but significant decreased in SBP. As a result, the rice grain quality became poor with the coated urea complex fertilizer application, but it could be improved by incorporation with fast-release fertilizer.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6C
• /
• pp.295-301
• /
• 2009

In general the stability of soil nail-slope system, the shear resistance is neglected because the tensile resistance of nail acts mainly for slope stabilization. This is because that deformed steel is generally used for nail and it does ductile behavior. In other side when the steel pipe with high rigidity is used for nail, the shear resistance at failure surface work more than deformed steel. In order to analyze effects of shear resistance at the soil nail-slope system with high steel piped nail, a series of numerical analyses were performed. Also numerical analyses at 3 conditions - 5 nailed, 7 nailed, 9 nailed at the same slope were perfomed for investigating the trend of shear resistance effect. From these 3D numerical analyses, it was found that the maximum shear resistances at each nails were larger in case of steel piped nail and because of this, the factor of safety at the condition of the steel piped nail appears larger than that of deformed steel nail.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.201.1-201.1
• /
• 2016

전주된 Invar (Fe-35%Ni) 박판 위에 증착된 Cu 박막은 스퍼터 전력량이 증가할수록 증착속도가 증가하였다. Cu/Invar 박판이 Invar 박판보다 면저항 값이 34%로 작았다. Invar 박판 위에 Cu가 증착되면 최대자화와 투자율은 각각 40.3, 65.0 [%] 감소하였다. Cu 박막의 탄성하강강성도, 마찰계수, 피로한계는 각각 45, 0.130, 0.093 이었다. 동적 나노 압침법으로 얻은 Invaar/Cu 박막의 하중-시간-변위 곡선의 가장 큰 차이는 탄성하강강성도(elastic stiffness) 이었다. 미세경도와 나노경도의 실험적 관계식은 $Y[GPa]=9.18{\times}10^{-3}X[Hv]$ 이었다. 나노압침선단의 하중분포를 이차원 선형 및 비선형 유한요소해석을 통하여 1.0 [mN] 의 정적하중을 가한 Cu 박막은 486 [mN] 으로 예측되었다. 이는 표면탐침현미경으로 관찰한 압흔의 변형정도와 유사한 경향을 보였다.

• Proceedings of the Korean Information Science Society Conference
• /
• 2005.11b
• /
• pp.793-795
• /
• 2005

지식 시스템(knowledge system)을 구축한다는 것은 구조적인 지식(structured knowledge)과 추론 모델(reasoning model)을 개발하기 위한 활동을 모델링하는 것을 말한다. 특별히 모델을 재사용한다는 것은 새로운 응용(application)을 만드는 데 있어서 비용과 시간을 감소시켜 준다. 서로 다른 응용과 영역(domain)에서 지식 구성요소를 재사용 한다는 것은 전문가 지식의 습득과 추론 과정을 정확하게 기술하는데 도움을 주게 된다. 본 연구에서는 문제해결방법 재사용에 대한 기존의 몇 가지 방법들을 함께 사용함에 의해서 급성복통과 관련된 질환 진단 태스크를 모델링할 수 있는 진단시스템을 제안하여 기존 시스템과 비교했을 때 지식 획득율을 향상시키게 되었다.