• Electrical & Electronic Materials
• /
• v.3 no.3
• /
• pp.187-194
• /
• 1990

광자기 메모리용 재료인 비정질 TbFe 박막을 대상으로 열자기 기록시 박막에 분포하는 온도와 이때 만들어지는 bit의 크기간에 상호관련성을 조사하였다. 레이저 조사에 의해 가열된 박막의 온도분포는 유한요소법을 이용한 열전달 해석에 의해 계산하였다. 레이저 가열종료 직전 박막 면에 분포하는 온도 contour로 부터 bit 크기를 예측하였다. 여기서 bit 크기는 온도 상승에 따라 보자력이 약화되어 외부자계와 박막반자장의 합력이 역자구를 만들어 준다고 가정하여 이 경계가 되는 온도(Tcrit)로 이루어지는 등온선의 크기로부터 정하였다. 열자기 기록 실험으로부터 기록 bit의 크기(Dmeas.)을 측정하여 레이저조사조건별로 예측한 bit크기(Dpred.)와 비교하였다. 특히, 레이저 pulse시간 변화에 따른 여러온도의 등온선 contour 직경변화를 조사하여 실측한 bit크기와 비교 검토함으로써 bit형성에 미치는 온도분포의 영향을 조사하였다. 이 결과 레이저 pulse시간이 길어지거나 레이저 power가 상대적으로 작을때 실측한 bit크기가 예측된 bit크기보다 커지는 것으로 나타났으며 이는 Tcrit 온도구배가 완만해질수록 bit경계가 되는 온도가 낮아지는 것으로 해석된다.

• Korean Journal of Optics and Photonics
• /
• v.8 no.6
• /
• pp.482-485
• /
• 1997

A new laser Doppler velocimeter employing a $CO_2$laser has been developed by using its optogalvanic effect. A change in the electric impedance of a discharge, induced by mixing of a returned wave with an originally existing wave inside the cavity, was employed to detect the Doppler frequency shift. A Doppler frequency shift as much as 60 KHz was detected, and also a good linear relationship between the velocity and the Doppler frequency shift was obtained.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.543-547
• /
• 2002

We have constructed two extended-cavity diode lasers which are phase-locked with a 9.2 GHz frequency offset. We adopted a digital servo circuit for the phase-locking. The relative linewidth of the phase-locked lasers was less than 2 Hz. Using the measured beat spectrum, we found the carrier concentration to be about 93 %. We measured phase noise and relative frequency stability of the lasers. The Allan deviation at the gate time of 20 s was $2.7{\times}10^{-19}$.

• Journal of IKEEE
• /
• v.15 no.4
• /
• pp.313-318
• /
• 2011

The effects of external continuous wave optical injection on spectral comb of a 10 GHz harmonically mode-locked semiconductor fiber ring laser have been studied. Greater than 40 dB spectral deeps in the spectral comb and greater than 30 dB reduction of supermode beating noise are achieved by injecting coherent light with ~ 100 KHz spectral width. To examine the possibility of using a low-cost seed source, we replace the seed source by a DFB laser with ~ 10 MHz spectral width. It shows similar spectral deeps, however supermode beating noise enhancement, rather than reduction, is observed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1209-1215
• /
• 2012

Experiments with premixed flames in a tube have been conducted to investigate the transition phenomenon from a laminar flat flame to turbulent motions. To induce this phenomenon, a flat flame is formed in a tube. Then, the local velocity at the center of the flat flame surface is increased using $CO_2$ laser irradiation. The deformed flame front propagates with an increase in the total flame surface and oscillating instability. Eventually, the flame front accelerates explosively, and it shows turbulent flame motions with a strong noise. The dynamic behaviors of the flame front prior to the turbulent motions are analyzed in this study to elucidate this process. The physical model of the process is presented according to observations.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1691-1693
• /
• 2001

펄스형 Nd:YAG 레이저는 연속형에 비해 효율이 높고 높은 첨두 출력(peak power)이 가능하므로 가공에 있어서 여러 가지 장점이 있다. 더구나 레이저 펄스 모양을 가변시키는 기능은 펄스형 Nd:YAG 레이저로 가공하기 힘든 특수분야에까지 가공을 가능하게 하였다. 본 연구에서는 3개의 플래쉬램프를 순차 점등시키는 MD(multi-discharge)방식의 레이저 시스템을 설계 및 제작하여, 램프 점등 시간의 변화에 따른 레이저 빔의 펄스폭과 펄스 세기(펄스 크기)를 조사하였다. 즉, PIC One-Chip microprocessor를 이용하여 실시간으로 3개의 플래쉬램프를 순차적으로 점등시켜 보다 다양한 펄스 모양을 만드는 기술을 개발하였다. 위 방식의 장점은 램프의 점등 지연시간을 0 $\sim$ 10ms 까지 다양하게 변화시킬 수 있고, 외부의 키보드로 실시간 제어가 가능하므로 보다 편리하게 펄스 모양을 변화시킬 수 있다. 또한 긴 펄스를 만들 수 있어 산업용 가공이나 의료용으로 널리 사용될 수 있을 것이다.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1069-1077
• /
• 2008

The railway abrasion measurement system have to satisfy two conditions to increase the measurement accuracy as follows. The laser region which is projected on the rail have to be extracted without the geometrical distortion. The mapping of the acquired laser region data on the rail profile have to be processed exactly. But, the conventional railway abrasion measurement system is deeply effected by the foreign substance( dust, rainwater, and so on ) on the railway or the sensitive response characteristic of the laser to the external measurement circumstance, and then the measurement errors arise from above factors. When the laser region is projected on the rail extracts from the acquired image, the interference of the light with the same frequency as the laser system occurs the serious problems. In the process of the mapping between the railway profile and the extracted laser region, the measurement accuracy is very highly effected by the geometrical distortion and the abnormal variation. In this Paper, we propose the novel method to increase the accuracy of the railway abrasion measurement dramatically. we designed and manufactured the high precision and fast image processing board with DSP Core and FPGA to measure the railway abrasion. The image processing board has the capability that the image of 1024X1280 from camera can be processed with the speed of 480 frame/sec. And, we apply the image processing algorithm base on the wavelet to extract the laser region is projected on the rail exactly. Finally, we developed high precision railway abrasion measurement system with the error range less than +/-0.5mm by which 2D image data is covered 3D data and mapped on the rail profile using the camera model and the perspective transform.

• Korean Journal of Optics and Photonics
• /
• v.18 no.5
• /
• pp.317-322
• /
• 2007

We performed injection-locking by two independent semiconductor lasers and investigated the spectral modes of the injection-locked laser From the observation of the saturated absorption spectrum in the $^{85}Rb$ D1 transition line, we have confirmed that the frequency of the injection-locked slave laser is synchronized by the frequency of the master laser, and the slave laser has a narrow linewidth after injection-locking. According to the intensity injected into the slave laser, we measured the variation of the injection-locking range and the mode of the injection-locked slave laser by using the confocal Fabry-Ferret interferometer. In the case of the incomplete injection-locking, we observed the competition between the free running mode of the slave laser and the mode of the master laser and analyzed the modes of the injection-locked slave laser.

• Journal of the Korea Computer Industry Society
• /
• v.2 no.7
• /
• pp.975-982
• /
• 2001

In this study, a solid-state laser system adopting a new real time multi-discharge (RTMD) method in which three flashlamps are turned on consecutively was designed and fabricated to examine the pulse width and the pulse shape of the laser beams depending upon the changes in the lamp rum-on time. That is, this study shows a technology that makes it possible to make various pulse shapes by turning on three flashlamps consecutively on a real-time basis with the aid of a PIC one-chip microprocessor. With this technique, the lamp turn-on delay time can be varied more diversely from 0 to 10 ms and the real-time control is possible with an external keyboard, enabling various pulse shapes. In addition, longer pulses can be more widely used for industrial processing and lots of medical purposes

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.1
• /
• pp.187-190
• /
• 2015

Recently, most of people wants to have smart life for themselves like smart phones. In this paper, we propose the smart elevator based on the laser screen, speakers and air fresheners. Using this elevator, we could enjoy the various screen inside, and we could keep contacting with manager for wifi in the emergency situation. Also, the elevator could be operated with user's motion for Kinect. Finally, we did the survey for understanding preference of smart elevator. The grops are elevator manufacturing company, elevator distribution corporation and consumers, each group have 200 people.